Search Results

The fatty acid methyl esters (FAME's) - in Europe mostly RME (Rapeseed methyl ester) - are used in several countries as alternative biogene Diesel fuels in various blending ratios with fossil fuels (Bxx). Questions often arise about the influences of these biocomponents on the modern exhaust aftertreatment systems and especially on the regeneration of Diesel particle filters (DPF). In the present work different regeneration procedures of DPF systems were investigated with biofuels B0, B20 & B100. The tested regeneration procedures were: passive regenerations: DOC + CSF; CSF alone, active regenerations: standstill burner; fuel injections & DOC. During each regeneration on-line measurements of regulated and unregulated emission components (nanoparticles & FTIR) were conducted. It can be stated that the increased portion of RME in fuel provokes longer time periods to charge the filter with soot.

During the VERT *) testing of different DPF systems it was remarked, that the oxidation catalyst converts sometimes a big part of NO to NO2, producing on the one hand a more toxic composition of the exhaust gases and causing on the other hand measuring artefacts, which tend to underestimate of NO2 and NOx by the cold NOx - measurement. The present work summarizes the experiences in this matter elaborated at the Laboratories for IC-Engines & Exhaust Emissions Control (AFHB) of the University of Applied Sciences Biel-Bienne, Switzerland, during several VERT activities and didactic projects on engine and chassis dynamometers in the years 2000-2006.

Limited and non-regulated emissions of scooters were analysed during several annual research programs of the Swiss Federal Office of Environment (BAFU) *). Small scooters, which are very much used in the congested centers of several cities, are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investigations of particle emissions of different 2-stroke scooters with direct injection and with carburettor were performed. The nanoparticulate emissions were measured by means of SMPS, (CPC) and NanoMet. Also the particle mass emission (PM) was measured with the same method as for Diesel engines. Extensive analyses of PM-residuum for SOF/INSOF, PAH and toxicity equivalence (TEQ), were carried out in an international project network. Particle mass emission (PM) of 2-S Scooters consists mostly of SOF.

The Diffusion Size Classifier (DiSC) is a new instrument to measure number concentration and average diameter of nanometer sized particles in the size range 10 - 200nm. It is small, easily portable and battery operated and therefore well suited for field measurements. The measurement range is suitable for ambient air concentrations (1000 - 500000 particles/cm3); together with a diluter it can be used for emission measurements. The number concentrations measured with DiSC agree well with those measured with a condensation particle counter. The response time is short enough to measure transient engine operation. The DiSC is therefore a useful instrument for number concentration measurements in non-laboratory settings.

The UN-ECE Particle Measurement Programme (PMP) has considerably gained momentum since the European Commission published the regulation details of Euro 5/6 for light duty vehicles, including a limit value for the number of particles emitted from passenger car tailpipes, to be enforced as early as Euro 5. A PMP-compliant particle number counting system retrieves its exhaust gas sample from a CVS tunnel and consists of two dilution stages before and after an evaporation tube, and a condensation particle counter. For each of these systems, compliance with the PMP guidelines has to be proved in terms of measurement performance. A required key property is the system's ability to evaporate liquid and volatile exhaust gas components, while properly transmitting solid particles to the number counter. Particle Number Count is able to distinguish between different filling states of a DPF as well as between DPF substrates with different porosity.

This paper discusses the possibility of equipping Euro 3 and older vehicles with a universal retrofit kit to reduce the NOX and the PM emissions without producing any secondary effect. Out of several configurations, the optimal setup for EGR and DPF regeneration was evaluated and tested on a passenger car engine testbench. Stationary results showed that with a low pressure EGR it was possible to reduce the NOX emissions by more than 50%, and the filtration efficiency of the DPF was greater than 99%. After various dynamic tests on the test bench to improve the control algorithm, the system was designed to be installed on a garbage truck.

An active oxidation catalyst is an efficient measure to reduce not only gaseous components (CO, HC), but also particle emissions (mostly oil condensates) of a small 2-stroke engine with lost oil lubrication. Since the 2- and 3-wheelers with 2-stroke propulsion are still a very serious source of air pollution worldwide in many urban areas, it is important to have a look on some consequences of an improperly working catalyst. The present paper shows some results of user-oriented aging of catalyst on the vehicle and results of limited emissions and unlimited (nano)particles during the catalysts screening tests. The works are a part of an international scooter network project, which was performed (2004 to 2007) in the Laboratories for IC-Engines & Exhaust Emission Control of the University of Applied Sciences, Biel, Switzerland with main support of the Swiss Federal Office of Environment (BAFU), Swiss Petrol Union (EV) and Swiss Lubes (VSS).

The “Reproducible Exhaust Simulator” (REXS) is a new combustion soot generator, based on the principle of a laminar diffusion flame. Soot is extracted from the stabilized flame by rapid cooling with dilution air. Due to its combustion origin, REXS soot is very similar to Diesel soot in terms of particle morphology, chemistry and size distribution, while its stability is far better than that of a Diesel engine. The soot generator can be operated against rising backpressure from a loading filter. A case study for the quality control of filter elements from mass production is presented. REXS soot is fed into filter samples, and their filtration characteristics are assesses using established nanoparticle measuring techniques. Filtration efficiency of 3 samples exceeded 99.99%, but decreased to some 99.5% for a short time after regeneration events. Leaks in the filter substrate, simulated by boring holes of 0.7 mm2 each into some end plugs, increased particle penetration 100-400 fold.

A filter system is presented which allows the reduction of the concentration of ultrafine particles in vehicle cabins to very low levels. The original ventilation system is switched to the recirculation mode and all cabin intake air is supplied via a retrofitted filter system. Tests with a variety of different vehicles (from passenger cars to coaches) show the efficiency of the system.

Advances in emission control technologies have demanded development of new ceramic chemistries and improved microstructures in catalytic substrates and especially in diesel particulate filters. High porosity filters are desirable, as they decrease engine backpressure and enable application of advanced catalysts including, but not limited to, multi-functional filters (MFF). A significant recent development has been in the use of ceramic fibers to create cross-linked microstructures in extruded honeycomb ceramics. This development allows high porosities to be attained while maintaining mechanical strength. However, according to the World Health Organization, certain classes of ceramic fibers are considered to have adverse health effects if released in air and inhaled.

New Diesel exhaust gas aftertreatment systems, with combined DPF*) and deNOx (mostly SCR) systems represent a very important step towards zero emission Diesel fleet. These combined systems are already offered today by several suppliers for retrofitting of HD vehicles. Reliable quality standards for those quite complex systems are urgently needed to enable decisions of several authorities. The present report informs about the international network project VERT *) dePN (de-activation, de-contamination, disposal of particles and NOx), which was started in Nov. 2006 with the objective to introduce the SCR-, or combined DPF+SCR-systems in the VERT verification procedure. Examples of results for some of the investigated systems are given. These investigations included parameters, which are important for the VERT quality testing: besides the regulated gaseous emissions several unregulated components such as NH3, NO2 and N2O were measured.

2- and 3-wheelers with 2-S propulsion are still a very serious source of air pollution worldwide in many urban areas. Therefore, every effort to reduce the emissions of those vehicles is an important contribution to improve the air quality. In the present work detailed investigations of regulated emissions and of particle emissions of 2-stroke scooters with direct injection and with carburator were performed. To demonstrate the emission reduction potentials some possibilities of emission improvements were grouped into steps. These technical measures were: ○ Higher tier lube oils ○ Lower oil dosing ○ Active oxidation catalyst ○ Supplementary filtration & oxidation devise (WFC) **) ○ Special fuel. Particle mass and nanoparticles (number), which are amply present in 2-stroke exhaust gas and which contribute strongly to the toxicity level are still unlimited by the international exhaust gas legislation. They were extensively investigated in the present project series.

The objectives of the present work are to investigate the regulated and unregulated (particle) emissions of a classical and modern 2-stroke and a typical 4-stroke scooter with different ethanol blend fuels. There is also comparison of two different ethanol fuels: pure ethanol (E) *) and hydrous ethanol (EH) which contains 3.9% water and is denatured with 1.5% gasoline. Special attention is paid in this research to the hydrous ethanol, since the production costs of hydrous ethanol are much less than those for (dry) ethanol. The vehicles are with carburettor and without catalyst, which represents the most frequent technology in Eastern Asia and offers the information of engine-out emissions. Exhaust emissions measurements have been performed with fuels containing ethanol (E), or hydrous ethanol (EH) in the portion of 5, 10, 15 and 20% by volume. During the test systematical analysis of particle mass (PM) and nano-particles counts (NP) were carried out.

Different Diesel Particle Filters (DPF)*) were tested on a 2-Stroke Detroit-Diesel bus engine 6V 92 TA. The investigations focused on soot burden and regeneration of the DPF with special filter materials. Also examined was promoting the regeneration by: throttling, additive (FBC), oxidation catalytic converter upstream of DPF and the catalytic coating of the filter material. The metrics were the particulate matter emission, its composition and the nanoparticles. The most important results are: The average SOF content in the engine exhaust particulate matter is 77.6 % and the majority of it is emitted as bigger droplets The wire-mesh filter catalyst (WFC) - a novel emission reduction technology -substantially curtails the SOF and PM. WFC traps and oxidizes the oil droplets and produces a “dry” soot. This can be very advantageous for the DPF downstream of WFC. (WFC can be also very interesting for 2-S gasoline engines).

1 Small off-road 2-stroke SI-engines have very high pollutant emissions. The Swiss environmental protection agency (BUWAL) investigates the state of the technology and emissions with the scope to show the potential of improvements by means of the best available technology (BAT) and to motivate the consumers to use the more sophisticated equipment and cleaner fuels to protect their health and the environment. In the present work emission measurements of chainsaws were performed with a special concern of particulate emissions. Particulates were analysed by means of: gravimetry, SMPS, NanoMet and differential analysis of filter residue. The varied conditions were: A/F-ratio, lube-oil content and the fuel quality. It has been shown, that the particulate mass and the nanoparticle numbers, which both consisting almost exclusively of unburned lube-oil, attain very high values. They are strongly influenced by the mixture tuning and by the lube-oil content.

Decreased particle concentration due to the use of particulate traps poses new challenges to particle measurement methods in terms of sensitivity and repeatability. In the present paper nanoparticle measurement methods are compared to gravimetric and Coulmetric analysis of filter samples from CVS sampling. Repeatability and sensitivity of the methods are assessed, and the influence of dilution and sampling is investigated. It is shown that the repeatability of nanoparticle measurement methods is of the same order as that of PM measurement. In terms of sensitivity, nanoparticle methods are by three orders of magnitude better than today's PM and EC measurement. This provides a much better signal-to-noise ratio, especially when particle emissions are very low. While a gravimetric “zero” measurement may still contain a lot of nanoparticles, a “zero” with a nanoparticle method is by a factor 1000 closer to particle free air.

1 In the present work investigations of a 7.8 liter-TC-IC-IVECO-CNG engine were performed with single point (SPI) *) and with multipoint (MPI) gas injection systems. Three types of MPI injectors available on the market were compared for stationary and transient engine operation. There are several advantages of MPI e.g. better possibility to equalize the air-fuel-ratio of the cylinders, optimization of the gas injection timing and of the gas pressure for different operating conditions. With different injector types there are different optimum injection timings, due to different injection durations, but at the optimum conditions there is little difference in the combustion quality. The injectors with higher flow rate can cause more λ-excursions in the dynamic response and with sudden changes of the gas pressure.

A well-balanced use of alternative fuels worldwide is an important objective for a sustainable development of individual transportation. Several countries have objectives to substitute a part of the energy of traffic by ethanol as the renewable energy source. The global share of Bioethanol used for transportation is continuously increasing. Investigations of limited and unregulated emissions of a flex fuel vehicle with gasoline-ethanol blend fuel have been performed in the present work on the chassis dynamometer according to the measuring procedures, which were established in the previous research in the Swiss Network to adequately consider the transient (WLTC) and the stationary operation (SSC). The investigated fuel contained ethanol (E), in the portions of 10% & 85% by volume. The investigated vehicle represented a newer state of technology and an emission level of Euro 5. The engine works with homogenous GDI concept and with 3-W-catalyst (3WC).

In the present paper some results of investigations of nanoparticles from five DI gasoline cars are represented. The measurements were performed at vehicle tailpipe and in CVS-tunnel. Moreover, five variants of “vehicle - GPF” were investigated. These results originate from the project GasOMeP (Gasoline Organic & Metal Particulates), which focused on metal-nanoparticles (including sub 20nm) from gasoline cars with different engine technologies. The PN-emission level of the investigated GDI cars in WLTC without GPF is in the same range of magnitude very near to the actual limit value of 6.0 × 1012 #/km. With the GPF’s with better filtration quality, it is possible to lower the emissions below the future limit value of 6.0 × 1011 #/km. There is no visible nuclei mode and the ultrafine particle concentrations below 10mm are insignificant. Some of the vehicles show at constant speed operation a periodical fluctuation of the NP-emissions, as an effect of the electronic control.

The most efficient way and the best available technology (BAT) to radically reduce the critical diesel emission components particles (PM&NP) and nitric oxides (NOx) are combined exhaust gas aftertreatment systems (DPF+SCR). SCR (selective catalytic reduction) is regarded as the most efficient deNOx-system, diesel particle filters are most efficient for soot abatement. Today, several suppliers offer combined systems for retrofitting of HD vehicles. The presented results are part of the work in the international network project VERT *) dePN (de-activation, de-contamination, disposal of particles and NOx), which has the objectives to establish test procedures and quality standards and to introduce the SCR-, or combined DPF+SCR-systems in the VERT verification procedure.