Search Results

Gasoline Homogeneous Charge Compression Ignition (HCCI) combustion has been studied widely in the past decade. However, in HCCI engines using negative valve overlap (NVO), there is still uncertainty as to whether the effect of pilot injection during NVO on the start of combustion is primarily due to heat release of the pilot fuel during NVO or whether it is due to pilot fuel reformation. This paper presents data taken on a 4-cylinder gasoline direct injection, spark ignition/HCCI engine with a dual cam system, capable of recompressing residual gas. Engine in-cylinder samples are extracted at various points during the engine cycle through a high-speed sampling system and directly analysed with a gas chromatograph and flame ionisation detector. Engine parameter sweeps are performed for different pilot injection timings and quantities at a medium load point.

A Stochastic Reactor Model (SRM) has been used to simulate the transition from Spark Ignition (SI) mode to Homogeneous Charge Compression Ignition (HCCI) mode in a four cylinder in-line four-stroke naturally aspirated direct injection SI engine with cam profile switching. The SRM is coupled with GT-Power, a one-dimensional engine simulation tool used for modelling engine breathing during the open valve portion of the engine cycle, enabling multi-cycle simulations. The model is initially calibrated in both modes using steady state data from SI and HCCI operation. The mode change is achieved by switching the cam profiles and phasing, resulting in a Negative Valve Overlap (NVO), opening the throttle, advancing the spark timing and reducing the fuel mass as well as utilising a pilot injection. Experimental data is presented along with the simulation results.

The flow and heat transfer phenomena in the intake port of a spark ignition engine with port fuel injection play a significant role in the mixture preparation process, especially at part load. The backflow of the hot burned gas from the cylinder into the intake port when the intake valve is opened breaks up any liquid film around the inlet valve, influences gas and wall temperatures, and has a major effect on the fuel vaporization process. The backflow of in-cylinder mixture with its residual component during the compression stroke prior to inlet valve closing fills part of the port with gas at higher than fresh mixture temperature. To quantify these phenomena, time-resolved measurements of the hydrocarbon concentration profile along the center-line of the intake port were made with a fast-response flame ionization detector, and of the gas temperature with a fine wire resistance thermometer, in a single-cylinder engine running with premixed propane/air mixture.

Recent studies in the USA have revealed that the catalysts (which are universally fitted to gasoline automobiles) are failing in service to an unacceptable extent. Although the reasons for the failures are not completely clear, it seems that misfiring, leading to highly exothermic reaction in the catalyst, may be responsible for the damage. Legislation is to be enacted later in this decade to address this problem by requiring on board diagnostic (OBD) systems which can measure misfire, as well as catalyst hydrocarbon (HC) conversion efficiency. Although some ideas have been suggested for the OBD requirements, no fully satisfactory sensor technology has yet appeared. This paper describes a novel hydrocarbon sensor based on a surface catalysis principle. The fundamental studies reported here have been made with the automobile application in mind. A catalytic chemi-ionisation model is proposed in order to enhance our understanding of this surface ionisation.

Partially premixed compression ignition (PPCI) engines operating with a low temperature highly homogeneous charge have been demonstrated previously using conventional diesel fuel. The short ignition delay of conventional diesel fuel requires high fuel injection pressures to achieve adequate premixing along with high levels of EGR (exhaust gas recirculation) to achieve low NOx emissions. Low load operating regions are typified by substantial emissions of CO and HC and there exists an upper operating load limitation due to very high rates of in-cylinder gas pressure rise. In this study mixtures of gasoline and diesel fuel were investigated using a multi-cylinder light duty diesel engine. It was found that an increased proportion of gasoline fuel reduced smoke emissions at higher operating loads through an increase in charge premixing resulting from an increase in ignition delay and higher fuel volatility.

Highly homogeneous compression ignition is difficult to achieve in a direct injection diesel engine. The difficulty of achieving adequate fuel vaporization and the problems of fuel spray wall impingement are the main factors. Limitation of the maximum operating load results from high rates of pressure rise that occur in this combustion regime. The levels of HC and CO emissions are raised substantially when compared with conventional combustion and remain a significant emission factor. In this study, two methods of achieving highly homogeneous combustion in a direct injection diesel engine were investigated, Nissan MK type and early injection. The effects of fuel injection pressure, injection timing, EGR level, EGR cooler efficiency and compression ratio were examined using a conventional 4 cylinder 2.0L common rail diesel engine with 18.4:1 and 14.4:1 compression ratios.

A new fast response NO detector, based on the chemiluminescence (CLD) method has been used to measure continuous, real time levels of NO in the cylinder, and simultaneously in the exhaust port of a virtually unmodified production SI engine. The real time NO concentration data show a great deal of information. Simultaneous NO measurements taken in-cylinder at sample points a few millimetres apart show substantial differences. Exhaust and in-cylinder levels from the same cycle show even greater differences, though the levels on average are well correlated.

The gas velocity through an automotive catalyst has been determined by measuring the time of flight of a pulse of propane injected at the inlet plane of the catalyst. The arrival time at the exit plane was detected by a fast flame ionization detector. By synchronizing and delaying the injection of propane with respect to the engine crankshaft position, the fluctuations of the exhaust gas velocity during the engine cycle were investigated. A number of tests at different engine load and speed points were carried out. The results show a complex velocity/time characteristic, including flow reversals. The technique is shown to be a viable option for flow measurement in this harsh environment.

A novel Fast Response Chemiluminescence Detector and a Fast Flame Ionization detector have been used to examine the instantaneous NO and unburnt hydrocarbon concentration in the cylinder and exhaust port of a DI Diesel engine. The in-cylinder results indicate very high levels of NO in the premixed phase of combustion, followed by generally lower levels during the diffusion burning phase. Hydrocarbon signals also indicate significant detail. The in-cylinder uHC signal is consistent with the probe location being between two of the fuel sprays. Both in-cylinder and exhaust results indicate rather high cyclic variability in the NO levels at steady conditions. Variations in the timing and structure of the exhaust uHC signal during the valve open period with load may give insight into the fuel spray/air motion.

A novel mechanical method of achieving a rapid switch between stoichiometric and lean conditions for SI engines is explored. Two and three throttle configurations, a switch strategy which employs a standard intake manifold and an assembly of pipes and throttle(s), are investigated numerically by using a one-dimensional engine simulation program based on the method of characteristics. The results indicate that it is possible to achieve rapid AFR switch without a torque jump, i.e. unperceptible to the driver.

An established Stochastic Reactor Model (SRM) is used to simulate the transition from Spark Ignition (SI) to Homogeneous Charge Compression Ignition (HCCI) combustion mode in a four-cylinder in-line four-stroke naturally aspirated direct injection SI engine with cam profile switching. The SRM is coupled with GT-Power, a one-dimensional engine simulation tool used for modeling engine breathing during the open valve portion of the engine cycle, enabling multi-cycle simulations. The mode change is achieved by switching the cam profiles and phasing, resulting in a Negative Valve Overlap (NVO), opening the throttle, advancing the spark timing and reducing the fuel mass as well as using a pilot injection. A proven technique for tabulating the model is used to create look-up tables in both SI and HCCI modes. In HCCI mode several tables are required, including tables for the first NVO, transient valve timing NVO, transient valve timing HCCI and steady valve timing HCCI and NVO.

Experimental data was obtained from a Rover K4 optical access engine and analyzed with a combustion analysis package. Cyclic NO values were calculated by mass averaging the measurements obtained by a fast NO analyzer. While the mass averaged results were used as the basis of comparison for the model, results indicate that mass averaging a fast NO signal is not nearly as critical as mass averaging a fast FID signal. A computer simulation (ISIS - Integrated Spark Ignition engine Simulation) was used to model the NO formation on a cyclic basis by means of the extended Zeldovich equations. The model achieves its cyclic variability through the input of experimentally derived burn rates and a completeness of combustion parameter, which is based on the Rassweiler and Withrow method of calculating mass fraction burned and is derived from the pressure-crank angle record of the engine.

The amount of residual gas present in the cylinder has a well documented effect on the combustion event at idle. The high levels of burnt gas present at low engine speed leads to significant cyclic variability. This paper presents research which indicates that the temperature of the residual gas, which can vary from event to event depending on the spark timing, also has a significant effect on the combustion torque. The more the spark timing is retarded from MBT timing, the more thermal energy is present in the exhaust gas. The idle speed control strategy typically varies the spark to give fast torque actuation for good speed regulation and hence the temperature of the residual gas may change significantly within the space of a few events. The paper shows evidence of the phenomenon (with fixed engine speed and air mass flow) and discusses possible causes. It then proceeds to develop a dynamic model for the behaviour.

This paper describes the application of a non-dispersive infrared-based instrument designed to measure CO with a response time of 7ms. Spark ignition engine emission measurements recorded during the first 505 seconds of an FTP75 drive-cycle for a 4 cylinder engine are presented, including fast response hydrocarbon and NO measurements. An analysis of the engine-out (pre-catalyst) exhaust gas is provided. Data collected simultaneously with a standard emissions test stand and conventional dilution tunnel are compared to the high frequency measurements. Fast CO analysis provides new insight into cold-start fuelling calibration and cylinder-to-cylinder AFR variation. Under rich conditions, the strong dependence of CO production on the quantity of excess fuel allows a significantly faster estimate of engine stoichiometry than a UEGO sensor.

Particulate emissions from IC engines associated with transient engine conditions are very important (similar to the legislated gaseous emissions). This is true both during real-world and test cycle driving. This paper describes an instrument for measuring the number of particles, and their spectral weighting, in the 5nm to 1000nm size range, with a time response of 200ms. This is achieved via an electrostatic classification technique, consisting of a diffusion charger followed by a multi-element, constant voltage, classifier. Conversion of the data to other metrics, such as mass, is also described. Results are presented from artificial test aerosols and from light and heavy duty diesel engines on standard test cycles.

The residual gas fraction prior to ignition at the vicinity of the spark plug in a single cylinder, two-valve spark ignition engine was measured with a fast-response flame ionization hydrocarbon detector. The technique in using such an instrument is reported. The measurements were made as a function of the intake manifold pressure, engine speed and intake/exhaust valve-overlap duration. Both the mean level of the residual fraction and the statistics of the cycle-to-cycle variations were obtained.

This paper describes a novel catalytic oxidation sensor which represents an attempt to realise a practical sensor for on vehicle detection of catalyst efficiency and misfire. Via experimental and modelling approaches, promising characteristics are established, which could mean that an application to the on-vehicle detection of catalyst efficiency and misfire is feasible.

The paper presents a computer simulation of flow and heat transfer phenomena in the intake port of a spark ignition engine with port fuel injection. Engine cold starting conditions are studied including the effects of in-cylinder mixture back flow into the port. One dimensional air flow and wall fuel film flow models and a two dimensional fuel droplet flow model have been developed using a combination of finite difference approaches. As a result, predictions are obtained that provide detailed picture of the air-fuel mixture properties along the intake port. The model may be of special importance for exhaust gas ignition system simulation as it will provide data concerning mixture formation under conditions of excessive fuel injection during engine start-up. The calculations performed are shown to be phenomenologically correct.

The transport of fuel during cold start in the intake of a port-injected engine has been investigated using a standard engine with very little modification. A fast response FID sampling from the intake manifold is used to measure the instantaneous vapor concentration during the start. At short times after the start, the engine is stopped, and the port under investigation isolated. The engine is then warmed up by passing hot water through it and at the same time is flushed with hot air, in the port and the cylinder. This evaporates the liquid fuel, and by integrating the vapor concentration multiplied by mass flow of the displaced gas, the fuel mass in the isolated port and cylinder is measured. It is shown how the mass of liquid in the port at the time at which the engine is stopped can reliably be related to the concentration measurement. By stopping the engine at different times after the start, detailed accounting of the fuel transport as a function of time since start can be made.

Experiments to cyclically resolve the HC concentration emitted by an I.C. engine with improved sampling techniques are described. The results suggest that the technique is easy to use, and gives results which are comparable with those obtained by other methods.