Search Results

To control natural-gas HCCI combustion, internal exhaust gas recirculation (EGR) by exhaust valve reopening (EVRO) during the induction stroke was applied to a single-cylinder test engine. The results demonstrate that combustion phasing can be controlled successfully by adjusting the EGR ratio, and so improvement of thermal efficiency and reduction in unburned exhaust emissions are feasible. In addition, the results of the EVRO method were compared to those of intake-valve pilot opening (IVPO) during the exhaust stroke. It was shown that EVRO is more useful than IVPO as a heat-recovery method for HCCI combustion.

The boiling point curve of fatty acid methyl esters (FAME), or biodiesel fuel, can be adapted to that of diesel fuel by breaking FAME down into a low-molecular structure using a cross-metathesis reaction with a short-chain olefin. Reformulated FAME by a metathesis reaction consists mainly of medium-chain olefins and fatty acid methyl esters. In the present study, the engine performance and exhaust emissions from reformulated FAME were investigated through engine bench tests. Surrogate fuels made from typical chemical components of reformulated FAME were used to clarify the effects of respective components upon combustion. Surrogate fuels were made by mixing 1-decene, 1-tetradecene, methyl laurate, methyl palmitate, and methyl oleate to simulate the boiling point, oxygen mass concentration, and calorific value of reformed biodiesel of waste cooking oil methyl ester (WME). A single-cylinder diesel engine equipped with common-rail-type injection system was used.

The objective of this study was to obtain an improved understanding of the effects of the simultaneous use of cold flow improver (CFI) and antioxidant on the cold flow properties, oxidation stability and diesel exhaust emissions of various biodiesels and biodiesel blends. Cold flow properties were evaluated by assessing the cloud point (CP) and pour point (PP) values, as well as from the results of the cold soak filtration test (CSFT). Oxidation stability was also determined by measuring the peroxide induction period (IP). The neat biodiesels (B100) derived from soybean oil(SME), Jatropha curcus oil(JME), rice bran oil(RBME), palm oil(PME) and waste cooking oil(WME), and biodiesel blends with JIS No.2 diesel fuel were tested. A CFI and antioxidant specially designed for use in biodiesel fuels were employed during the work. The experimental data demonstrated that the addition of antioxidant had no effect on either the CP or PP values.

The main aim of this study is to investigate the effect of NO and NO2 on the combustion characteristics such as pressure development and combustion phasing in natural gas HCCI engine. A secondary aim is to demonstrate a method of obtaining a significant sensitizing effect on methane oxidation reaction from small amounts of NOx. Experiments were conducted using a rapid compression-expansion machine that was constructed from a single-cylinder diesel engine. First, the sensitizing effect of NO and NO2 on the HCCI combustion of natural gas was investigated in a case where NOx was uniformly mixed into a charge. Obtained results show that the auto-ignition timing is significantly advanced and an acute heat release is promoted by adding either NO or NO2.

In this study, the influence of compression ratio on engine performance and variations of auto-ignition timing in each cylinder were evaluated in a 4-cycle multi-cylinder natural gas engine with PCCI combustion system. In experiment, the compression ratio was systematically changed from 19 to 25. From the result, it was clarified that an increase in compression ratio makes not only the improvement of engine output and fuel economy but also the reduction of NOx emission, even though the mechanical loss is increased. Simultaneously, the variation of auto-ignition timing in each cylinder can also be reduced.

The experimental study has been carried out on a diesel engine dual-fueled by wood-pyrolysis gas and biodiesel fuel. Wood-pyrolysis gas was simulated by a low-calorie mixed gas (LCG), which consists of hydrogen, methane and inert gas. Effects of LCG/biodiesel ratio, biodiesel injection-timing, and gas-fuel composition were examined. Obtained results show that under a constant-torque condition, an increase in gas fuel consumption causes a decrease in a brake thermal efficiency due to a decrease in combustion efficiency and specific heat ratio. Also, NOx emission in exhaust gas is decreased by increase in gas fuel consumption under the low load condition, while it shows no change under the relatively high load condition. In addition, an early injection of biodiesel is effective to reduce carbon monoxide emission due to increase in combustion pressure and temperature.

To clarify the microcrystal structure of soot particulate in the combustion chamber, we examined sampling methods which freeze the reaction of sample specimens from the combustion chamber and collected the soot particulates on microgrids. We investigated the microcrystal structure with a high resolution transmission electron microscope. The results were: the particle size distribution and the microcrystal structure of the soot particulates is little different for the cooled freezing method and room temperature sampling. The typical layer plane structure which characterizes graphite carbon is not observed in the exhaust of diesel engines, but some particulates display a somewhat similar layer plane structure. The structure of soot particulate is a turbostratic structure as the electron diffraction patterns show polycrystals. The soot particulates in the combustion chamber is similar to exhaust soot particulates.

In this study, measurement methods of aldehydes and volatile organic compounds (VOCs) from off-road engine have been investigated. Also, their emission characteristics have been evaluated. By using high-performance liquid chromatograph (HPLC), aldehydes could be measured with small variation. Major aldehydes from off-road engine are formaldehyde and acetaldehyde. Total aldehydes emission is not necessarily low compared to THC emission. The emission characteristics of aldehydes are similar to that of CO, THC and PM. For VOCs sampling, sampling tube with absorbent was better than sampling bag because some kinds of VOCs tend to become absorbed on the sampling bag. Except for 1,3-butadiene, VOCs could be measured with small variation by using gas chromatography-mass spectrometer (GC-MS). Benzene, toluene and xylene were major species found in VOCs. The emission characteristics of VOCs were also similar to ones of CO, THC and PM.

The performance of a medium duty DME truck was evaluated by field tests and engine bench tests. The DME vehicle was given a public license plate on October 2004, after which running tests were continued on public roads and a test course. The DME vehicle could run the whole distance, about 500 km, without refueling. The average diesel equivalent fuel consumption of the fully loaded DME truck was 5.75 km/l, running at 80 km/h on public highways. Remedying several malfunctions that occurred in the power-train subsystems enhanced the vehicle performance and operation. The DME vehicle accumulated 13,000 km as of August, 2006 with no observed durability trouble of the fuel injection pump. Disassembly and inspection of the fuel injectors after 7,700 km operation revealed a few differences in the nozzle tip and the needle compared to diesel fuel operation. However, the injectors were used again after cleanup.

In this study, diesel exhaust emission characteristics were investigated as GTL (Gas To Liquid) fuel was applied to a heavy-duty diesel truck which had been developed to match a Japanese new long-term exhaust emission regulation (NOx < 2.0 g/kWh, PM < 0.027 g/kWh). The results in this study show that although the test vehicle has advanced technologies (e.g. high pressure fuel injection, oxidation catalyst, and urea-SCR aftertreatment system, etc.) which are applied to reduce diesel emissions, the neat GTL fuel has a great advantage to reduce particulate matter emissions and poly aromatic hydrocarbons. And regarding nano-size PM emissions, nuclei mode particles emitted during idling are significantly decreased by using the GTL fuel.

Biodiesel fuel has attracted much attention as a carbon neutral fuel because it is made from vegetable oil. Especially in Southeast Asia, there are numerous biofuel resources, such as palm oil and coconut oil, and it is desirable to utilize these for CO2 reduction. In this paper, we evaluate the properties of biodiesel fuel and biodiesel blended diesel oil. The low temperature performance of palm oil methyl ester (PME) is poor and it affects low temperature performance, even if the PME blending rate is low. The oxidation stability is a very important property of biodiesel fuel because degraded biodiesel fuel produces organic acids and polymeric substances. PME contains mainly saturated fatty acids methyl esters, so the oxidation stability is better than other fats and oils. When containing antioxidants such as beta carotene, biodiesel's oxidation stability is improved.

In this study, it was attempted to operate the 4-cycle multi cylinder natural gas engine introduced PCCI combustion system without electric heater for intake air heating. In experiment, by optimization of the compression ratio and in addition to the control of spark ignition timing, the engine could be operated using only intake air heating with coolant water. The results showed that the suppression of the auto-ignition timing variations among cylinders owing to the independent spark timing control of each cylinder leads to the improvement of engine output, fuel economy and exhaust emissions. Furthermore, this paper describes the engine starting and corresponding change of engine load on electric demand on generator. The stable operation could be achieved by using spark ignition, controlling of excess air ratio and intake air temperature during change the engine load from idle to rated power.

It has been clarified that diesel fuel properties have a great effect on the exhaust emissions and fuel consumption of a conventional diesel combustion regime. And as other diesel combustion regimes are applied in order to improve exhaust emissions and fuel consumption, it can be supposed that the fuel properties also have significant effects. The purpose of this study is to propose the optimum diesel fuel properties for a premixed compression ignition (PCI) combustion regime. In this paper, the effect of the auto-ignitability of diesel fuels on exhaust emissions and fuel consumption was evaluated using a heavy-duty single-cylinder test engine. In all experiments, fuels were injected using an electronically controlled, common-rail diesel fuel injector, and most experiments were conducted under high EGR conditions in order to reduce NOx emissions.

In this study, a piezo disk was used to generate a cloud of n-decane fuel drops, which were mixed with air, then carried into a combustion chamber and ignited by a platinum wire. Microgravity data obtained at the Japan Microgravity Center (JAMIC) were compared to normal gravity data, all at 1Atm pressure and 20+/-1°C initial temperature. Under normal gravity the lean limit was found to be 7.6x106/mm3 (Φ = 1.0), and from this point the flame front speed steadily increased from 20cm/s up to a maximum flame front speed of 210cm/s at a fuel drop density of about 14x106/mm3 (Φ = 1.85). Microgravity data showed a much richer lean limit - about 14.5x106/mm3 (Φ = 1.9), and the flame front speed did not gradually rise to a peak value. Instead, the measurements indicated a peak value of about 250cm/s, with a steep increase followed by a gradual decrease at richer fuel air ratios. A cellular flame structure appeared, and the cell size decreased as the mixture density increased.

Flame propagation at elevated pressures for propane, butane and autogas (20% propane and 80% butane by mass) were investigated. Flame arrival time was measured using ionization probes installed along the wall of a cylindrical combustion chamber. Flame radius was also measured using a laser schlieren technique. Results showed that the flame front speed decreased with increasing initial pressure, and the initial pressure effect on maximum flame front speed was correlated by the relationship Sf = 175·pi-0.15 (for Φ=1.0). Characteristics of flame front speed between propane, butane and autogas were very similar, whereas at fuel-rich conditions flame front speed of butane and autogas were higher than that of propane. A thermodynamic model to predict flame radius and speed as a function of time was derived and tested using measured pressure-time curves.

Lean burn engines now being developed employ in-cylinder injection which requires high pressures and so necessitates expensive injection equipment. The experiments reported here used air assisted in-cylinder injection, and injected a mixture of air and fuel during the intake stroke, so allowing atomization at lower injection pressures than those necessary in compressing fuel with solid injection. The experiments confirmed that operation in this manner resulted in similar output and fuel consumption as with a carburetor. Next, a divided combustion chamber was installed and connected to the main combustion chamber and air assisted in-cylinder injection from a reed type injection nozzle was attempted. With this arrangement, stable idling operation was possible to air-fuel ratios (A/F) of 70. Lean burn at A/F = 22 to 35 was also achieved at maximum rated outputs (3.7 kW at 4200 min-l) of 6 - 18 %.

The combustion mechanism of a fuel droplet cloud was studied by numerical simulation. We investigated how the flame front speed and combustion products changed depending on the equivalence ratio and initial temperature. Modeling was performed using the KIVA-III software package, a three dimensional analysis software used mainly for internal combustion engine applications. The computational domain was a horizontal 1x1x100 cell sector of a spherical combustion chamber and the fuel was n-decane. Results showed that when all the fuel droplets were assumed to have evaporated, the flame front speed increased from 28 cm/s to 152 cm/s as the equivalence ratio increased. The maximum flame front speed was reached at ϕ=1.1, beyond which it decreased (at richer overall equivalence ratios). With a constant equivalence ratio, the flame front speed decreased near the outside region, because the unburned gas was compressed by the expanding burned gas.

DME as a fuel for compression ignition (diesel) engines has been actively studied for about ten years due to its characteristically low pollution and reputation as a “smokeless fuel”. During this time, the practical application is taking shape based on necessary tasks such as analysis of injection and combustion, engine performance, and development of experimental vehicles. At this moment, standardization of DME as a fuel was started under ISO in 2007. There are concerns regarding the impurities in DME regarding the mixing during production and distribution as well as their effect on additives for lubricity and odor. In this report, the effect of DME fuel impurities on performance of a DME powered diesel engine was investigated. The platform was a DME engine with common-rail fuel injection and was evaluated under partial load stable mode and Japanese transient mode (JE05) testing parameters.

The tasks to improve diesel emissions and fuel consumption must be accomplished with urgency. However, due to the trade-off relationship between NOx emissions, soot emissions and fuel consumption, clean diesel combustion should be achieved by both innovative combustion and fuel technologies. The objective of this study is to extend the clean diesel combustion operating range (Engine-out emission: NOx ≺ 0.2 g/kWh, Soot ≺ 0.02 g/kWh). In this study, performance of a single-cylinder test engine equipped with a hydraulic valve actuation system and an ultra-high pressure fuel injection system was investigated. Also evaluated, were the effects of fuel properties such as auto-ignitability, volatility and aromatic hydrocarbon components, on combustion performance. The results show that applying a high EGR (Exhaust gas recirculation) rate can significantly reduce NOx emission with an increase in soot emission.

In this study, advantages of GTL fueled DI diesel engine were observed, then, some cautionary areas, notably the aptitude for sealing materials, were investigated. Some advantages of using GTL as a diesel engine fuel include reduction of soot emission levels, power output and fuel consumption with GTL to conventional diesel fuel operation is equivalent, super-low sulfur content of GTL and its liquid state at normal temperature and pressure. However, there are some problems with putting GTL fuel on the market, such as lubricity, aptitude for sealing materials, high cetane index and high pour point. It is necessary to use additives to improve GTL's lubricity, and selecting the most appropriate type of lubricity improver is also important. The influence of GTL on the swelling properties of standard rubber materials seem basically the same, but it is necessary to notice on used rubbers.