Search Results

The statistical energy analysis (SEA) is widely used to support the development of the sound package of cars. This paper will present the preparation of a model designed to investigate the sound package of the new Audi A3 and associated correlation against measurements. Special care was given during the creation of the model on the representation of the structure to enable the analysis of structure borne energy flow on top of the classical airborne analysis usually done with SEA. The sound package was also detailed in the model to allow further optimization and analysis of its performance. Two real life load cases will be presented to validate the model with measurements. First, the dominating powertrain and a second load case with dominating rolling noise. An analysis of the contribution of the different source components and a way to diagnose the weak paths of the vehicle will be presented. The focus of this investigation is the application of optimally adjusted treatment.

During series production of modern combustion engines a major challenge is to ensure the correct operation of every engine part. A common method is to test engines in end-of-line (EOL) cold test stations, where the engines are not fired but tugged by an electric motor. In this work we present a physically based 0D model for dynamic simulation of combustion engines under EOL test conditions. Our goals are the analysis of manufacturing faults regarding their detectability and the enhancement of test procedures under varying environmental conditions. Physical experiments are prohibitive in production environments, and the simulative approach reduces them to a minimum. This model is the first known to the authors exploring advanced engine test methods under production conditions. The model supports a wide range of manufacturing faults (with adjustable magnitude) as well as error-free production spread in engine components.

Good lighting is crucial for safe driving at night. Unfortunately, many parameters are contributing to the final result of the individual tolerances of car body, dynamics and headlamp: the resulting aim. The paper will analyze individual tolerance contributors from car body parameters like load, tire pressure, suspension as well as temperature parameters of chassis and plastic parts. The investigation shows that the headlight aim can fluctuate in a worst case scenario more than ±0.3°.

The paper will describe actual investigations on safety improvements by new lighting functions. Especially the new chance of projections on the road surface either by simple reflector technology or by modern signature and pattern projection will be investigated. Different prototype patterns will be checked by a set of new parameters, e.g. reaction time to signals, clear understanding, minimum and optimum visual contrasts. The results show that high contrasts and dynamic effects are most effective.

Brake particle emissions as a part of non-exhaust emissions are becoming more and more relevant, various international research activities can be stated. Also from the legislation side, first hints are given in regards of possible regulations. One possible approach for the reduction of brake particle emissions deals with the collection of those particles close to the foundation brake. The presented paper will follow such an approach and give some insights. In a first step, the technical layout is described for bench and vehicle testing. While for bench testing a PMP-like style of the setup could be chosen, the vehicle test setup is oriented on conventional wheel dust measurements. Hence, presented results of laboratory testing are dealing with PN and PM measurements. Also the impact on particle size distribution is discussed. It can be stated, that the particle collecting system is able to improve PN and PM emissions. Additionally, ultra-fine particles are almost eliminated.

Lightweighting of cars will remain one important goal for car producers. One milestone for lightweight technologies was the Audi Space Frame ASF‚. New generations of ASF cars will follow. Only the experience from the A 8 shows, which innovative technologies for these new generations will bring us one step forward. It's the combination of alloy modifications, innovative forming and joining technologies that leads into the future.

For integrating Life Cycle Assessment into the design process it is more and more necessary to generate models of single life cycle steps respectively manufacturing processes. For that reason it is indispensable to develop parametric processes. With such disposed processes the aim could only be to provide a tool where parametric environmental process models are available for a designer. With such a tool and the included models a designer will have the possibility to make an estimation of the probable energy consumption and needed additive materials for the applied manufacturing technology. Likewise if he has from the technical point of view the opportunity, he can shift the applied joining technology in the design phase by changing for instance the design.

In the production of brake disc pads, powder mixes containing, metal chips, filling agents, and abrasive materials, as well as phenolic resins are processed and molded to a back plate by way of pressure and temperature. These molded disc pads reach their final strength through additional thermal treatment such that the phenolic resins approach “full cure”. This production process leads to anisotropic, viscoelastic, and to a certain extent heterogeneous materials which are - like the brake system- increasingly subject to even greater demands. E.g. apart from tribological characteristics, more and more focus is placed on structure-mechanical properties to improve the braking comfort.

This paper shall give an idea of a lighting strategy a car company could have decided in an senior management circle. It is a medium to long term approach dealing with styling, design, innovation, quality and environmental aspects. Cost influences will be pointed out. It gives examples how different target conflicts could be handled and how or where to find mutual gain. Some “natural” conflicts between styling, engineering and marketing in car development are discussed. The different roles a car company could play in the development process will be shown. Is a car company responsible for the application of parts only or should it take the development leadership? And how could it be in future? Chances and risks will be pointed out.

Issues relating to the reduction of CO₂ emissions and energy consumption are currently more important than ever before. In the construction engineering and automotive sectors research and development efforts are focused closely on efficient buildings and automobiles. The designated target is a reduction in greenhouse gas emissions and overall energy demand. However, almost all approaches focus solely on either "buildings" or "mobility." By considering both aspects as a single holistic system, further energy saving potential arises due to synergetic effects. The goal of current research projects relating to Smart Homes and Vehicle to Building (V2B) is to smooth the electrical load profile on a household level rather than to reduce the individual-related total energy consumption and thereby the CO₂ emissions.

Two research fields are presented in this paper covering new lighting functions. In the first part, a study is presented that evaluates distraction by light animations. 41 test subjects were involved, and a situation was constructed with several traffic participants and an animated-light vehicle parked so as to be conspicuously within the test subjects’ view. 91% of the test subjects stated they felt little or no distraction or impairment from the light display on the parked car. 29% noticed something conspicuous about the test vehicle. 22% indicated they had noticed the car’s lights flashing as its central locking system was operating. Only 7%—three of the 41 participants—noticed the animations in addition to their traffic monitoring. Of these, two said they didn’t feel disturbed at all by the animations while the third found it only very slightly distracting. Nobody said the distraction or impairment was “neutral”, “little bit” or “strong”.

This paper covers research findings on digital projections on the road. Data is provided for the root cause analysis of non-existing distraction proven by several studies. The study describes if and in which geometrical space road projections are visible to other road traffic participants. Such participants can be e.g. oncoming, passing drivers or pedestrians standing aside the road. The paper data shows where projections are recognizable and assignable to the original intention of the projection. A grid was created to identify the areas where digital projections could be understood and where the digital projections were just illegible. A dominant factor is the grazing incidence. The photons are distributed over a larger area and only the driver’s view makes a virtual compression of the illuminated area in order to make the signals legible. The results show that distraction for other road participants is unlikely for any position outside very limited areas.

When designing new vehicles, the legal requirements of the countries in which the vehicles are homologated must be observed and implemented. The manufacturers try to consider the legal framework of the UN-ECE (United Nations Economic Commission for Europe), CCC (China Compulsory Certification) and FMVSS (Federal Motor Vehicle Safety Standard) 108 in the same vehicle to keep the variance low. For the appearance of the vehicle, the position of the light modules in the front of the vehicle is important. In addition to the surface requirements of lighting functions, the positions of the low beam (LB), high beam (HB) and the position of daytime running lights (DRL) are also regulated. When it comes to these mounting positions, the legislation between the US and the EU differs quite significantly.

A wide-ranging investigation into the sensitivity of the hybrid RANS-LES based OpenFOAM CFD process at Audi was undertaken. For a range of cars (A1, TT, Q3 & A4) the influence of the computational grid resolution, turbulence model formulation and spatial & temporal discretization is assessed. It is shown that SnappyHexMesh, the Cartesian-prismatic built-in OpenFOAM mesher is unable to generate low y+ grids of sufficient quality for the production Audi car geometries. For high y+ grids there was not a consistent trend of additional refinement leading to improved correlation between CFD and experimental data. Similar conclusions were found for the turbulence models and numerical schemes, where consistent improvements over the baseline setup for all aerodynamic force coefficients were in general not possible. The A1 vehicle exhibited the greatest sensitivity to methodology changes, with the TT showing the least sensitivity.

The electrification of the powertrain and the thereto related recuperation of the electric engine saves the energy in the battery and thus reduces the thermally dissipated brake energy, which leads to lower brake rotor temperatures compared to combustion engine vehicles (ICEVs). These new conditions enable to reconsider brake disc concepts. Including lightweight design in heavy battery electric vehicles (BEVs) and the increasingly reliant corrosion resistance of brake rotors, Aluminum is a promising approach for new brake disc concepts. In the past, Aluminum brake disc concepts have already been deployed. For instance Aluminum Metal-Matrix Composite (Al-MMC) concepts in the Lotus Elise S1 and on the rear axle of the Volvo V40 [1]. The presented concept is a different approach and separates the friction system from the bulk Aluminum brake disc, achieved by coating of the friction rings.

New human-machine interfaces are the direct result of digitalization. So also in lighting, new constellations have to be taken into account when looking to the possibilities of giving additional informations to the driver. Lighting and furthermore information given by light is a clear preference during nighttime driving. The global interest in standardization of light driven messages from autonomous vehicles to other traffic participants has opened new research needs in order to prepare full view on such new human-machine interface. In Europe, GTB (Group de Travail de Bruxelles) has established a working group dedicated to this topic. In order to provide a complete picture of the effects of digital light, the question of additional glare contribution by digital informations, i.e. extra projected light in form of patterns, symbols or areas was addressed in this research study. This article will show the investigations on wet and dry road glare while driving with digital informations.

The current automotive electronic and electrical (EE) architecture has reached a scalability limit and in order to adapt to the new and upcoming requirements, novel automotive EE architectures are currently being investigated to support: a) an Ethernet backbone, b) consolidation of hardware capabilities leading to a centralized architecture from an existing distributed architecture, c) optimization of wiring to reduce cost, and d) adaptation of service-oriented software architectures. These requirements lead to the development of Zonal EE architectures as a possible solution that require appropriate adaptation of used security mechanisms and the corresponding utilized hardware trust anchors. 1 The current architecture approaches (ECU internal and in-vehicle networking) are being pushed to their limits, simultaneously, the current embedded security solutions also seem to reveal their limitations due to an increase in connectivity.

E-mobility is a game changer for the automotive domain. It promises significant reduction in terms of complexity and in terms of local emissions. With falling prices and recent technological advances, the second generation of electric vehicles (EVs) that is now in production makes electromobility an affordable and viable option for more and more transport mission (people, freight). Current e-vehicle platforms still present architectural similarities with respect to combustion engine vehicle (e.g., centralized motor). Target of the European project EVC1000 is to introduce corner solutions with in-wheel motors supported by electrified chassis components (brake-by-wire, active suspension) and advanced control strategies for full potential exploitation. Especially, it is expected that this solution will provide more architectural freedom toward “design-for-purpose” vehicles built for dedicated usage models, further providing higher performances.

The current development of automotive lighting strives towards more and more lighting installations on vehicles. Additionally, to that, manufacturers start animating these lighting installations as coming home or leaving home greetings from the car to the driver. In a previous paper we have shown, that these additional animations are in fact not distracting to other road users and when used correctly, e.g. in a sequential turn indicator, can be beneficial to the overall traffic safety. This study then aims to investigate the potential influence of illuminated logos on road safety. European lawmakers forbid the use of illuminated advertisements on vehicles to minimize the danger of distraction for other road users and thereby negatively influencing traffic safety. As of now, active illumination of the manufacturer’s logo is considered an advertisement.

Digitalization in Industry and Society is progressing quickly. Up to now, just 5 static and standard lighting applications have been dominating in the U.S. (Low/High Beam, Daytime Running Lamp Turn Indicator & Position Lamp). The global interest in standardization of light driven messages from autonomous vehicles to other traffic participants has opened new research needs and research findings. In Europe, GTB has established a working group dedicated to this topic. The article will discuss the possible contribution of signalling and lighting functions to Digitalization and Autonomous driving by explaining the first elements of functional definition and research results.