Search Results

The success of stratified combustion is strongly determined by the injection and ignition system used. A large temporal and spatial variation of the main parameters - mixture composition and charge motion - in the vicinity of the spark location are driving the demands for significantly improved ignition systems. Besides the requirements for conventional homogeneous combustion systems higher ignition energy and breakdown voltage capability is needed. The spark location or spark plug gap itself has to be open and well accessible for the mixture to allow a successful flame kernel formation and growth into the stratified mixture regime, while being insensitive to potential interaction with liquid fuel droplets or even fuel film. For this purpose several different ignition concepts are currently being developed. The present article will give an ignition system overview for stratified combustion within Delphi Powertrain Systems.

In order to allow continued production of the AM General Optimizer 6500 during MY 2007 through 2010 this IDI engine (Indirect Injection - swirl chamber) requires sophisticated aftertreatment controls while maintaining its fuel economy and durability. The main purpose of the development program was to retain the relatively inexpensive and simple base engine with distributor pump and waste-gated turbocharger, while adding hardware and software components that allow achievement of the phase-in emission standards for 2007 through 2010. The aftertreatment system consists of Diesel Oxidation Catalyst (DOC), NOx Adsorber Catalyst (or DeNOx Trap - DNT) and Diesel Particle Filter (DPF). In addition to the base hardware, an intake air throttle valve and an in-exhaust fuel injector were installed. The presented work will document the development process for a 2004 certified 6.5 l IDI heavy-duty diesel engine to comply with the 2007 heavy-duty emission standards.

The focus of this study is to determine the effect of using B-20 (a blend of 20% soybean methyl ester biodiesel and 80% ultra low sulfur diesel fuel) on the combustion process, performance and exhaust emissions in a High Speed Direct Injection (HSDI) diesel engine equipped with a common rail injection system. The engine was operated under simulated turbocharged conditions with 3-bar indicated mean effective pressure and 1500 rpm engine speed. The experiments covered a wide range of injection pressures and EGR rates. The rate of heat release trace has been analyzed in details to determine the effect of the properties of biodiesel on auto ignition and combustion processes and their impact on engine out emissions. The results and the conclusions are supported by a statistical analysis of data that provides a quantitative significance of the effects of the two fuels on engine out emissions.

The purpose of the present paper is to develop an engine simulation tool in a commercial CFD code to study the spray and mixing process that can be used to access the performance of a Gasoline Direct Injection (GDI) engine. The ignition, combustion and pollutant formation are strongly dependent on the quality of the fuel-air mixture. The fuel is injected directly into the combustion chamber by high-pressure fuel injector. The fuel atomization and evaporation process takes place due to the interaction of the small fuel particles generated by the injector and the in-cylinder air motion. Experimental study on the spray and mixing process is difficult and expensive, which has been recognized as a major obstacle towards the optimization of the combustion chamber geometry, engine components and the injection strategies.

A Robust Engineering experiment was performed to determine the effects PGM loading and placement on the FTP emissions of a 4 cylinder 2.4L and two 8 cylinder 4.7L vehicles. 1.3L catalytic converters were used containing a front and rear catalyst of equal volume. The experiment is defined by a Taguchi L-8 array. Eight different combinations of catalyst PGM loadings were aged and evaluated. Results show that nmHC and NOx emissions are predominately affected by the PGM loading of the front catalyst. The rear catalyst is insensitive to either Pt or Pd which can be used at low concentrations. Results also compare the benefits of Pd and Rh to reduce emissions. Confirmation runs suggest that significant reductions in PGM cost can be achieved over baseline designs.

Carbon canisters have been adapted for automobile use since the early 1970s to control evaporative emissions. Stringent emission regulations and the requirement for an enhanced evaporative emissions test procedure, make this an important issue. The air and evaporative fuel from the carbon canister therefore need important consideration with respect to air to fuel ratio (AFR) control and idle by-pass air control. Although a few complex models of the activated carbon canister have been developed, a control-oriented, simplistic carbon canister model needs to be developed. This paper explores the control-oriented modeling of a canister purge air system along with the on-line estimation of evaporative fuel loading of the activated carbon. An attempt was made at providing an analytical expression for the evaporative fuel and air entering the intake manifold.

Due to the stringent emission regulations, On-Board Diagnostics II (OBD II) and the requirement of enhanced evaporative emissions test procedure, an aggressive canister purge control strategy is required for automotive vehicles. The enhanced evaporative emissions test procedure has forced car manufacturer to purge the carbon canister in the vehicle idle condition so that production vehicles meet the SHED and hot soak test requirements. This not only worsens the idle speed quality but also tends to increase exhaust emission levels. Using analytical models of evaporative air and fuel, feed-forward control strategy for both idle by-pass air and air to fuel ratio can be improved. This paper demonstrates an application of evaporative system modeling to the idle air and air to fuel ratio control.

As automotive power-train systems become more efficient, less waste heat is available for vehicle passenger cabin warming. As a result, alternative heating technologies are being investigated to alleviate this shortcoming. One alternative is to operate the existing A/C system in reverse (heat pump mode), thus providing supplemental heat. Recently, the environmental impact of refrigerant emissions has come under global scrutiny. The concern is their potential for global warming. Thus, the environmental characteristic of merit that makes for a more benign refrigerant in terms of emissions is lower Global Warming Potential (GWP). R-152a is a more environmentally benign refrigerant compared to R-134a with a GWP of 120 vs. 1,300 [1] and [2]. Both refrigerants are hydro-fluorocarbons - HFCs - (contain no chlorine) and hence, have zero ozone depletion potential. An environmentally benign refrigerant touted as a potential replacement for R-134a, is CO2.