Search Results

The human thermal comfort, which has been a subject of extensive research, is a principal objective of the automotive climate control system. Applying the results of research studies to the practical problems require quantitative information of the thermal environment in the passenger compartment of a vehicle. The exposure to solar radiation is known to alter the thermal environment in the passenger compartment. A photovoltaic-cell based sensor is commonly used in the automotive climate control system to measure the solar radiation exposure of the passenger compartment of a vehicle. The erroneous information from a sensor however can cause thermal discomfort to the occupants. The erroneous measurement can be due to physical or environmental parameters. Shading of a solar sensor due to the opaque vehicle body elements is one such environmental parameter that is known to give incorrect measurement.

This paper presents the hybrid technique application in identifying the noise transfer paths and the force transmissibility between the interfaces of the different components in the vehicle. It is the stiffness based formulation and is being applied for the low to mid frequency range for the vibration and structure borne noise. The frequency response functions such as dynamic compliance, mobility, inertance, and acoustic sensitivity, employed in the hybrid method, can either be from the test data or finite element solution or both. The Source-Path-Receiver concept is used. The sources can be from the road surface, engine, transmission, transfer case, prop-shaft, differential, rotating components, chain drives, pumps, etc., and the receiver can be driver/passenger ears, steering column, seats, etc.

Neck injury assessment is part of the FMVSS208 requirements. Hardware tests are often conducted to validate whether the vehicle safety system meets the requirements. This paper presents a full vehicle finite element model using LS-DYNA, including structural components, restraint system components, and dummies. In the case of a frontal impact at 30deg angle, in the areas of neck compression, neck extension and neck kinematics, it is demonstrated that a good correlation is achieved between the response of a FE dummy in the model and those of ATDs in the physical hardware tests. It is concluded that the math tool may be applied to comprehend test and design variations that may arise throughout a vehicle development lifecycle and to help develop a vehicle restraint system.

A unified approach to collision warning due to in-lane and neighboring traffic is presented. It is based on the concept of velocity obstacles, and is designed to alert the driver of a potential front collision and against attempting a dangerous lane change maneuver. The velocity obstacle represents the set of the host velocities that would result in collision with the respective static or moving vehicle. Potential collisions are simply determined when the velocity vector of the host vehicle penetrates the velocity obstacle of a neighboring vehicle. The generality of the velocity obstacle and its simplicity make it an attractive alternative to competing warning algorithms, and a powerful tool for generating collision avoidance maneuvers. The velocity obstacle-based warning algorithm was successfully tested in simulations using real sensor data collected during the Automotive Collision Avoidance System Field Operational Test (ACAS FOT) [10].

Shudder vibration of a hydraulic power steering system during parking maneuver was studied with numerical and experimental methods. To quantify vibration performance of the system and recognize important stimuli for drivers, a shudder metric was derived by correlation between objective measurements and subjective ratings. A CAE model for steering wheel vibration analysis was developed and compared with measured data. In order to describe steering input dependency of shudder, a new dynamic friction modeling method, in which the magnitude of effective damping is determined by average velocity, was proposed. The developed model was validated using the measured steering wheel acceleration and the pressure change at inlet of the steering gear box. It was shown that the developed model successfully describes major modes by comparing the calculated FRF of the hydraulic system with measured one from the hydraulic excitation test.

In France, as in other countries, accident research studies show that the greatest proportion of restrained occupants sustaining severe injuries and fatalities are involved in frontal impact (70% and 50% respectively). In severe frontal impacts with restraint occupants and where intrusion is not preponderant, the oldest occupants very often sustain severe thoracic injuries due to the seat belt. In the seventies, a few cars were equipped in France with load limiters and it was thereby possible to observe a relationship between the force applied and the occupant's age with regard to this thoracic risk. The reduction of intrusion for the most violent frontal impacts, through optimization of car deformation, usually translates into an increase in restraint forces and hence thoracic risks with a conventional retractor seat belt for a given impact violence.

By adapting vehicle control systems to the skill level of the driver, the overall vehicle active safety provided to the driver can be further enhanced for the existing active vehicle controls, such as ABS, Traction Control, Vehicle Stability Enhancement Systems. As a follow-up to the feasibility study in [1], this paper provides some recent results on data-driven driving skill characterization. In particular, the paper presents an enhancement of discriminant features, the comparison of three different learning algorithms for recognizer design, and the performance enhancement with decision fusion. The paper concludes with the discussions of the experimental results and some of the future work.

This paper demonstrates the benefit of using simulation and robust optimization for the problem of balancing vehicle noise, vibration, and ride performance over road impacts. The psychophysics associated with perception of vehicle performance on an impact is complex because the occupants encounter both tactile and audible stimuli. Tactile impact vibration has multiple dimensions, such as impact hardness and memory shake. Audible impact sound also affects occupant perception of the vehicle quality. This paper uses multiple approaches to produce the similar, robust, optimized tuning strategies for impact performance. A Design for Six Sigma (DFSS) project was established to help identify a balanced, optimized solution. The CAE simulations were combined with software tools such as iSIGHT and internally developed Kriging software to identify response surfaces and find optimal tuning.

The market growth for electric-hybrid passenger vehicles has been very significant and is expected to reach nearly 25% of all vehicles sold in the US by 2015. Hybrid commercial vehicles are also being developed by several OEM's. This paper discusses the progress of Delphi Thermal Systems in developing an integrated electric compressor drive with high cooling capacity (9 kW+), sufficient for large hybrid SUV's and commercial vehicles such as Class 8 tractors with sleeper. An important driver for use of the electric compressor in the hybrid truck application is the reduction of engine idling time while maintaining comfort in the cab or sleeper. Design details of a compact 5 kW SPM motor, its inverter drive, and issues related to its integration into the compressor housing are described. Test results are given confirming excellent performance.

This paper describes the methodology used to design and perform a CFD analysis of a Chevrolet Impala SS Funny Car body. This body was designed for the purpose of making it available for teams to race it in the National Hot Rod Association (NHRA) drag racing series beginning with the 2007 race season. Several challenges were presented in this project: (1) This was the first time a General Motors drag racing body for use in professional classes (Funny Car or otherwise) was ever designed in CAD. (2) The body was originally designed as a 2007 Chevrolet Monte Carlo. After the tooling was completed, changes in Chevrolet’s product lineup required that the body be changed to a 2007 Impala SS. (3) Budget constraints precluded CFD analysis until after the bodies were already being manufactured. There were several teams that raced the new body during the 2007 race season. One of these teams won the Funny Car Driver’s Championship.

A multi vector design tool to accurately predict instrument panel obscuration was developed to insure that critical legal displays in vehicles are not obscured. The concept provides for a computer generated light source shaped to replicate the human eyes. The light source is then projected onto a 3D math based arrangement and the resultant shadows are visible on the instrument panel surface and its displays. Design studios require criteria for the placement of the instrument cluster gages and displays, various controls, switches, and steering column stalks before an interior theme can be completed. Therefore, instrument panel obscuration and visibility must be determined early in the design process. The obscured areas are a function of the instrument panel surface, steering wheel rim, hub, spokes, and the location of the driver's eyes. This light source method allows engineers and designers the ability to quickly determine obscured areas.

A novel lateral sliding vehicle bucket seat was developed to address consumer needs for improved facile access to third row seats in minivans and sport utility vehicles. The concept provides for a second row bucket seat to slide laterally across a vehicle floor by roller mechanisms that roll across steel rails that transverse the vehicle floor. The system consists of two T-section type steel rails mounted parallel to each other at a distance equal to the seat riser support attachment features. The seat risers contain a roller mechanism that enables contact with the cylindrical portion of the steel rails. Each steel rail contains rectangular openings spaced appropriately to allow the seat latching mechanisms to engage securely. The seat riser supports at the rear include a releasable clamping mechanism hook that engages and disengages into the rectangular openings of the steel rails.

This paper presents an experimental protocol allowing to measure car accessibility motions and to evaluate associated discomfort feelings. The aim of these different approaches is firstly to acquire knowledge about motor strategies and secondly to be able to animate a numerical ergonomic mannequin. A video optoelectronic system has been used to acquire 3D movements data realized with 4 half french car units. A 3D digitizer has also been employed to measure static postures allowing to size and animate our numerical mannequin. Five voluntary subjects have participated to pre-experiments. Collected data have undergone several examination processes in order to prepare the mannequin animation. In other terms, kinematic analysis of body segments will allow to understand and to characterize ingress and egress movements from vehicles.

The paper addresses the connectivity issues related to integrating an Automated Model Based Calibration System (MTS Atlas) to a dynamometer test bed data acquisition system using an ASAM-GDI Interface. The GDI (Generic Device Interface) implementation was chosen over other ASAM interfaces due to its real-time capabilities and the ability to host new GDI drivers as these drivers become available. A structured migration process is developed showing how a new interface standard can be implemented that integrates with legacy test equipment, yet provides a simple low cost mechanism allowing replacement of old or redundant equipment.

Laboratory performance testing of larger tires requires system capability beyond larger diametric clearance and additional radial load capability. This paper describes a newly introduced Flat-Trac® tire test system designed for light truck tires and racing tires. Background on flat surface force and moment testing identifying the need for a system with more capability is presented. The MTS Flat-Trac LTR tire test system is introduced as a force and moment measurement system capable of testing light truck and racing tires. The first of these systems has been in operation at Bridgestone's Tokyo technical center since July 2002. Test results are presented to show that the Flat-Trac LTR (Light Truck/Racing) provides increased capability beyond the conventional Flat-Trac III CT (Cornering and Traction) system. Cornering force and longitudinal force test results are compared to show agreement between the Flat-Trac LTR and Flat-Trac CT systems.

Consumer expectations for automated vehicle operations such as automatic locking, remote ignition control, navigation, and entertainment are primary drivers for the increasing complexity of embedded automotive electronics modules. The prevalent practice for procuring these modules is to develop a written behavioral specification that is then used by an outside supplier to build and test the module. Validation test plans are written separately based on an understanding of the requirements. The challenges posed by the current practice include the inability to completely specify the expected behavior in a timely manner, the need to balance the design between low cost and new features demanded by the customer, and ensuring that the product exactly implements the specified behavior. Moreover, vehicle manufacturers desire the ability to explore sensitivity of specifications by identifying constraints on the system and assessing the product for ease of implementation.

A novel longitudinally sliding overhead video screen monitor was developed to address consumer needs for vehicles equipped with rear seat entertainment and long length sunroofs. Long length sunroof openings in vehicles are causing engineers to mount video screen monitors in locations other than the overhead. Typically, they are mounted on the floor console or on the back of front seat head restraints. Floor console mounted video screen monitors generally do not provide a comfortable viewing distance or angle for second and third row occupants. Head restraint mounted video monitors cause issues with seat shake and two monitors adds to the vehicle cost unnecessarily. The mountable sliding video monitor assembly comprises of a video display screen, brackets for mounting the monitor, a pair of tracks that are movable with respect to each other, a series of ball bearings, and a roof mounting bracket. The inner main track is adapted for mounting the pair of tracks to the vehicle.

Different countermeasure designs for reducing the HIC (d) and to comply with FMVSS201U have been evaluated in many component-level studies by suppliers and OEMs. This study presents guidelines to support future countermeasure and interior designs. FMVSS201U has changed the way OEMs design interiors of the vehicles today. Most recently, much more work is being done to find ways to design interiors of the vehicles that comply with FMVSS201U while keeping the interiors aesthetically pleasing, attaining driver comfort and meeting driver visibility requirements. Introduction of side-rail airbags has further affected countermeasure design and packaging. This study focuses on several countermeasure designs in the side-rail region as used in a mid-sized vehicle implemented to meet FMVSS201U requirements and their efficiency with respect to Head Injury Criterion (HIC) reduction given a fixed packaging space.

This paper describes the Human Factors (HF) research undertaken to support the new midgate incorporated in the Chevrolet Avalanche. This concept had several unique user interfaces not previously used in vehicle design and required several Human Factors studies to assess the usability of this concept. In addition, this paper discusses developing a protocol for conducting iterative Human Factors studies to assess the usability impact of product changes within the strict production program time lines.

This paper presents the fundamental principles of variation analysis and robust design for dimensional datum schemes. The kinematics equations for rigid body motions are simplified through linearization. The simplified formulations explicitly relate the dimensional deviations of a rigid part with its datum scheme configuration and dimensional variations at datum target points. This simplified approach can be used with either the first order Taylor series approximation or Monte Carlo simulation to study the statistical characteristics of datum scheme variations. A headlamp case study is presented that shows the application procedures and demonstrates that both Taylor series and Monte Carlo methods generate comparable results, but the former offers more efficiency and convenience due to its close form formulation. This approach has found many applications especially in on-site problem solving and fast what-if studies.