Search Results

The efforts of the ISO “Test Variability Task Force” have been aimed at improving the understanding and at reducing brake dynamometer test variability during performance testing. In addition, dynamometer test results have been compared and correlated to vehicle testing. Even though there is already a vast amount of anecdotal evidence confirming the fact that different procedures generate different friction coefficients on the same brake corner, the availability of supporting data to the industry has been elusive up to this point. To overcome this issue, this paper focuses on assessing friction levels, friction coefficient sensitivity, and repeatability under ECE, GB, ISO, JASO, and SAE laboratory friction evaluation tests.

Development of reliable magnesium (Mg) to steel joining methods is one of the critical issues in broader applications of Mg in automotive body construction. Ultrasonic spot welding (USW) has been demonstrated successfully to join Mg to steel and to achieve strong joints. In this study, corrosion test of ultrasonic spot welds between 1.6 mm thick Mg AZ31B-H24 and 0.8 mm thick galvanized mild steel, without and with adhesive, was conducted. Adhesive used was a one-component, heat-cured epoxy material, and was applied between overlapped sheets before USW. Corrosion test was conducted with an automotive cyclic corrosion test, which includes cyclic exposures of dipping in the 0.5% sodium chloride (NaCl) bath, a constant humidity environment, and a drying period. Lap shear strength of the joints decreased with the cycles of corrosion exposure. Good joint strengths were retained at the end of 30-cycle test.

It is well known that the drilling industry is a diverse industry with huge power needs for drilling deep wells. This paper discusses the drilling industry in general and the future need for HT power electronics to enable such activities as tractor drive drilling of deep horizontal wells. The discussion is geared at applications for drilling within the earth at ambient temperatures of 150°C and above.

The results of an experimental study in a DI Diesel engine are presented which shows that partial premixing, using direct diesel fumigation of the inlet air, achieved a reduction in the ignition delay, the magnitude of high frequency rapid pressure fluctuations, the maximum rate of pressure rise and the amplitude of the rate of the high frequency pressure oscillations. Two methods of diesel fumigation were investigated. The difference between these two methods was the degree of premixing of diesel fuel with the inlet air. The first technique used a fine (5 micron) diesel spray onto a glow plug and the second technique used prevaporised diesel. A Perkins 4-236 engine was run both with and without fumigation at two different steady state speeds roughly covering both city and highway running conditions.

A brief overview of the history and scope of the SAE Oil Labeling Assessment Program is presented. Then, the results of analyses on 893 samples of engine oil purchased in the retail market over the first three years of the program, are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API “C” category designation. Additionally, 43 engine oil samples found to be questionably labeled, were repurchased and analyzed; these results are included.

Modern approaches to durability assurance in ground vehicle design are reviewed in the context of recent developments in computer-based analytical and experimental tools for use by designers and development engineers. Examples, using an automotive wheel assembly, are presented to illustrate the application of fatigue analysis in product development. Major challenges associated with the linking of various design tools into integrated networks appropriately configured for industrial problem solving are discussed along with an assessment of the potential benefits to be gained from such integration.

A review of many years of published work has shown that hydrogen embrittlement can occur under rolling contact conditions. Breakdown of lubrication and contamination with water have been cited as the probable sources of atomic hydrogen. In this paper, a unique fracture morphology is identified and the mechanism of the fracture progression from initiation to final catastrophic failure is proposed. Development of beneficial residual compressive stress near the contacting surfaces is one approach used to avoid this type of failure. Several alternative methods capable of developing a more desirable stress distribution will be discussed.

This numerical study examines the chemical-kinetics mechanism responsible for EGR NOx reduction in standard engines. Also, it investigates the feasibility of using EGR alone in hydrogen-air and methanol-air combustion to help generate and retain the same radicals previously found to be responsible for the inducement of the autoignition (in such mixtures) in IC engines with the SONEX Combustion System (SCS) piston micro-chamber. The analysis is based on a detailed chemical kinetics mechanism (for each fuel) that includes NOx production. The mechanism for H-air-NOx combustion makes use of 19 species and 58 reactions while the methanol-air-NOx mechanism is based on the use of 49 species and 227 reactions. It was earlier postulated that the combination of thermal control and charge dilution provided by the EGR produces an alteration in the combustion mechanisms (for both the hydrogen and methanol cases) that lowers peak cycle temperatures-thus greatly reducing the production of NOx.

The Auto/Steel Partnership Corrosion Project Team has completed a perforation corrosion test program consisting of on-vehicle field exposures and various accelerated tests. Steel sheet products with eight combinations of metallic and organic coatings were tested, utilizing a simple crevice coupon design. On-vehicle exposures were conducted in St. John's and Detroit for up to seven years to establish a real-world performance standard. Identical test specimens were exposed to the various accelerated tests, and the results were compared to the real-world standard. This report documents the results of these tests, and compares the accelerated test results (including SAE J2334, GM9540P, Ford APGE, CCT-I, ASTM B117, South Florida Modified Volvo, and Kure Beach (25-meter) exposures) to the on-vehicle tests. The results are compared in terms of five criteria: extent of corrosion, rank order of material performance, degree of correlation, acceleration factor, and control of test environment.

The results of analyses on 300 samples of engine oil purchased in the retail market in 1990 are discussed. All samples were labeled with the API SF or SG Service Category, separately, or in combination with an API C category designation. Also, 17 oils previously found to be questionably labeled, from the 1989 set, were repurchased and analyzed. These results are included.

The introduction of MultiAir technology [8] has had a strong impact on engine performance, fuel consumption, emissions and control. This technology, intended at first for gasoline engines and applied only on intake valves, is aiming at the reduction of engine breathing losses and, as a consequence, reduction of pollutant emissions and fuel consumption, together with an improvement of maximum intake efficiency. Further positive effects of MultiAir technology have been a significant improvement of Low End Torque, engine driveability (“fun-to-drive” index) and other operating conditions (e.g. idle control). Current development of MultiAir technology is focusing on a better management of hot EGR (Exhaust Gas Recirculation), still acting only on the intake side, although with specifically designed valve lift profiles. This application of MultiAir technology is pushing gasoline engines towards new levels of performance improvements.

A hybrid electric vehicle simulation tool (IBZ-Simulator) has been developed at the Fuel Cell Institute of the University of Applied Sciences Esslingen to study the fuel economy potential of a Fuel Cell hybrid urban bus. In this paper, the fundamental architecture of the FC urban buses was described, as well as the control strategy to manage the power flow between the different elements of the drive train. A comparison of the hybrid with the conventional type and ICE-hybrid type is performed, and important factors relating to the vehicle efficiency (accessory loads, vehicle mass, Fuel Cell system ramping rate and battery capacity) were assessed. The using of supercapacitor (or ultracapacitors) as peak power buffer has been investigated.

Gear rattle, clunk, and other such noises, commonly referred to as impulsive or unusual noise, are often classified as unique problems without common origins. This paper examines the underlying structure that promotes them and traces physical system behaviors that predispose them to such noises. Though the audible noise itself is not modeled directly, a good deal of the disposable energy that sustains it can be inferred from the impulsive dynamics that underlies the whole process. Further effort quantifies the energies involved and appraises the distinctiveness of the perceived noise. Whether one hears gear rattle or clunk depends on the initiating site within the system and the impulsivity index of the prevailing dynamics. Observable indicators suggest that periodic noise is supported by periodic dynamics and, similarly, impulsive noise, by impulsive dynamics and that the latter is non-deterministic, discontinuous and even chaotic.

The timing of lubricating oil changes for passenger vehicles are based on set time or mileage intervals specified by their manufacturers. A few vehicle manufacturers use more sophisticated methods such as logging the engine speed and temperature and calculating the oil change intervals from this data. Neither technique tells the vehicle user anything about the true state of the oil. A novel form of viscosity sensor based on a vibrating piezoceramic element has been developed. Based on the output from such a device, a more accurate determination of the oil change interval can be made and abnormal conditions (such as the leakage of fuels into the lubricating oil) can be detected. This paper gives a brief description of the device itself and shows results from prototype samples.

A new form of SAE Transactions has been developed which allows for considerable flexibility in format, content, and distribution. A key volume includes abstracts of all SAE papers and a comprehensive depth index. Optional additions include printed and bound sets of all Transactions papers in full, subscriptions for all SAE papers, subscriptions for all SAE Transactions papers, and microfiche versions of each of these. No longer limited by physical size, all worthy papers can now be included in Transactions together with discussion, thereby enlarging the scope of Transactions approximately seven times.

There have been plastics in automobiles almost as long as there have been plastics. This paper deals with plastic molded parts from the 1930’s through 1970. These parts include steering wheels, tail light lenses, knobs, electrical connectors, fasteners, speedometer wheels, distributor caps, water pump impellers, dials, and various decorative ornaments.

This study applies the methodology developed for two earlier evaluations of diesel particulate controls to urban buses. Since these vehicles are used almost exclusively in urban areas where population is most dense, the analysis indicates the net benefits of control are very high.

The purpose of this paper is to survey the adverse environmental impacts resulting from motor vehicles, to review technologies developed to address these problems, and to summarize the current status of pollution control programs around the world.

Rapidly industrializing developing countries are now starting to note similar air pollution problems to those of the industrialized world. This paper surveys the adverse environmental impacts resulting from motor vehicles, reviews technologies developed to address these problems, and summarizes the current status of pollution controls around the world. Special focus is on the design of strategies to address the emerging problems of developing countries.

This paper deals with a conceptual aircraft cargo loader “that can do everything” commonly referred to as The Super Loader. The Super Loader is intended for use at air terminals to transport loads such as palletized cargo, containers, wheeled vehicles, shelters, and airdrop platforms from the storage docks to the military and civil aircraft, and vice versa. The loader may be described as a self-propelled, air transportable (in a C-141, C-17, C-5) 60,000 lb lifting capacity, adjustable height vehicle that will load/off load all transport aircraft from a C-130 whose cargo deck is only 3 feet, 3 inches high to a B-747 whose main deck upper limit is about 18 feet high. The Super Loader must also service the lower lobes of wide-bodies and main decks of narrow-bodied aircraft like the DC-8 and B-707. In brief, this loader will be required to interface with both civil and military cargo systems, present and future.