Search Results

In order to prevent lower extremity injuries to a pedestrian when struck by a car, it is important to elucidate the loadings from car front structures on the lower extremities and the injury mechanism caused by these loadings. In this study, using a human finite element (FE) model, a bending moment diagram and a stress diagram of tibia were introduced to examine the effects of loading from car structures. By the lower absorber of the car, the bending moment was distributed over the tibia with small moment at the upper tibia location that can reduce knee injury risk. Certain positions of the lower absorber reduced the tibia fracture risk. An FE analysis of a legform impact test using the TRL legform impactor was also conducted, and a relation was found between the injury criteria of the TRL legform impactor and the human FE model. High acceleration of the TRL legform impactor corresponded to the tibia fracture or MCL rupture of the human FE model.

Many ICs are used in various electronic components in automotive applications, such as ECUs (electronic control units) and smart actuators. Automotive ICs required the following features: (1) high integration of analog, digital and output devices; (2) high breakdown voltage for analog devices standing the battery voltage; (3) highly accurate control for analog circuits; (4) susceptibility under harsh operating conditions, such as high ambient temperature and high humidity; and (5) high surge immunity such as ESD (electrostatic discharge) robustness. To meet these requirements, we developed analog and output devices with improved surge endurance based on SOI wafer and trench-dielectric-isolation technologies. Analog circuit applications, especially accurate power management or high-precision solenoid driving, demands stable temperature-compensated output. Load dump and battery-jumping also needs high voltage protection and high noise immunity for these devices.

Increased interest in global warming issues requires rapid improvements in reduction of CO2 emissions. The automotive industry is placing high importance on improving fuel economy performance across their entire product lines. Charging Management System is a necessary element towards fuel economy improvement. Many of today's charging management systems perform at least two important functions: improving efficiency based on vehicle motion, and detecting battery state of charge. These systems become more complicated as more components (i.e. generators, current sensors and ECU) and software are added. Therefore, it is difficult to develop charging management systems for an entire product line and difficult to retrofit the system for vehicles already in production. A stand-alone charging management system solves these issues. This system is independent of the other vehicle systems. The software for improving fuel economy is installed in the generator or current sensor.

We have achieved significant weight reduction for the MS (Multi-Tank Super Slim Structure) Evaporator (1)currently in production at DENSO CORPORATION. The evaporator of HVAC unit, located in the instrument panel, is a component of the aluminum heat exchanger used in automotive air conditioners. The new evaporator uses thinner quad-layer sheet material, thanks to optimization of the electrical potential among its outer filler metal, intermediate anodic layer and core. The evaporator is thus lighter than conventional evaporators, but retains equivalent corrosion resistance.

Up to now, while automobile electric packages have demanded the high density for small and light products, electric leaks, which have occurred due to condensation, have been a major problem. To prevent any electric leaks, a conformal coating on the electric parts (ex. ECU: Electronic Control Unit) has been needed, but in general the design rules of the conformal coating (ex. Application area) is vague. Therefore, DENSO demands to clear the design rules of conformal coating electric package for higher reliability. To meet the demand, DENSO has developed a condensation simulation method using CAE that can show the occurrence condition of condensation fast and accurately. In the result, DENSO has been able to get the design rules where to need the conformal coating in the electric package for automobiles.

In 1997, we have applied laser technology to the world's first practical adaptive cruise control (ACC) system. The ACC system is based on 2-dimensional scanning laser-radar-sensor technology that is supported by highly reliable high power diode laser. Now, we have developed 34W output power multiple-quantum-well (MQW) diode laser. The power of 870nm near IR diode laser is twice as high as conventional one, thus it meets the strong needs for robust detection of the reflective laser beams from the moving vehicle ahead. Furthermore, Au-Sn-Ni a new alloy solder has been employed to sustain high degree of vibration and thermal shock to raise reliability. The acceleration life-tests at high temperature pulsed operation demonstrate the high reliability of developed 34W high power diode laser.

In an effort to protect the earth's environment, emission regulations in the diesel engine field are becoming increasingly strict. One way of meeting these regulations is to atomize the fuel spray by using a fuel injection system with high-pressure injection, which activates engine combustion. With current in-line pump systems, however, it is still possible to satisfy the demand for cleaner emissions by improving the fuel spray, through measures such as reviewing high-pressure injection and initiating improvements in the nozzle. This report describes the new in-line pump system for medium duty diesel engines to meet future emission regulations. In this report, we will describe how analytical technology, such as computer simulation, was used on the pump side to make improvements for higher injection pressure.

The lateral DMOS (LDMOS) had been developed for intelligent power IC[1][2] for ECU (Electric Control Unit). The process and device simulation methodology are used while developing a devices. The physical model and parameter in analytical model are calibrated to enhance the accuracy of the simulation and to reduce lead time and costs.

The challenge for the diesel engines today is to reduce harmful emissions, such as particulate matter (PM) and Nitrogen oxides (NOx), and enhance the fuel efficiency and power, which are its main advantages. To meet this challenge, DENSO has developed an advanced common rail system (CRS) that uses piezo actuated fuel injectors capable of delivering up to five injection events per combustion cycle at 180MPa, currently the world's highest commercially available diesel fuel injection pressure. The DENSO piezo injector incorporates an internally developed piezoelectric element that energizes quicker than its solenoid counterpart, thereby reducing the transition time for the start and end of the fuel injection event. The piezoelectric element and unique passage structure of the DENSO injector combine to provide a highly reliable and responsive fuel injection event.

Through the years, aluminum automotive heat exchangers have been developed in order to have a high performance and a light weight. Therefore, the thickness of the aluminum sheets for the application has been reduced. As the brazeability declines with the reduction in thickness, fins having a thickness under 80μm may be difficult to secure a good brazeability. Therefore, we studied the brazeability to determine the limit of thickness using clad fins from 40 to 80μm. The fillet volume formed at the joints of the fin and tube decreased with the decreasing fin thickness and the Si content in both the filler metals and the core alloys. The suitable range of Si content in the filler metals and the core alloys to obtain a good brazeability decreased with the decreasing fin thickness. When the fins were thinner than the critical values, it was impossible to have a good brazeability.

Conventional methods of physicochemical models require various experts and a high measurement demand to achieve the required model accuracy. With an additional request for faster development time for diagnostic algorithms, this method has reached the limits of economic feasibility. Machine learning algorithms are getting more popular in order to achieve a high model accuracy with an appropriate economical effort and allow to describe complex problems using statistical methods. An important point is the independence from other modelled variables and the exclusive use of sensor data and actuator settings. The concept has already been successfully proven in the field of modelling for exhaust gas aftertreatment sensors. An engine-out nitrogen oxide (NOX) emission sensor model based on polynomial regression was developed, trained, and transferred onto a conventional automotive electronic control unit (ECU) and also proves real-time capability.

In applying a LAN to automotive electronics systems, an optimal protocol has been adopted for each system so far, such as body electronics system, entertainment system, service system and power train system. As low cost communication protocol “BEAN” (Body Electronics Area Network; SAE paper 970297) adopted to wider range of functions on vehicle, ECU's numbers are increased which have BEAN communication and that is branched to plural communication networks. We have succeeded in rationalization of those network systems with the gateway function on a delegated ECU for each LAN system on vehicle. And this system also realized the connection to after market products by data exchange through the gateway function, while securing vehicle fail-safe.

With the diesel emissions and fuel consumption regulations and laws being tightened up, Common Rail System (CRS), capable of accurate and high-pressure diesel fuel injection, has become very popular in the world, and this CRS market is expected to continue to grow in the future. As use of the CRS becomes widespread, CRS is supposed to be used in a wide variety of environment, e.g. bad fuel (for example, much dust [1] and/or water), which increases concerns of CRS reliability. In an attempt to cope with such bad fuel properties, CRS and Fuel collected from the market was investigated. And based on this result, a new test method was worked out to simulate fuel stresses in the market. This test method verified the improved design of CRS with enhanced fuel robustness. This paper describes the new test method and the fuel robustness-enhancing effect of CRS based on the test method.

The set-off length (also referred to as the “lift-off length”) is reduced by the re-entrainment of the burned gas by the backward flow surrounding a diesel spray jet produced by a multi-hole nozzle. In the present study, to estimate the equivalence ratio at the set-off length, a means of estimating the amount of burned gas that is re-entrained into the near-nozzle region of the diesel spray jet was established. The results revealed that the suppression of soot formation in quasi-steady diesel spray flames produced by a multi-hole nozzle and a high injection pressure is not attained by reducing the equivalence ratio at the set-off length. Analysis of the amount of soot along the spray axis using a two-color method revealed that the maximum soot amount position appears in a quasi-steady spray flame, after the collapse of the head vortex in which a dense soot cloud is formed. The maximum soot amount position does not change even if the injection pressure varies.

Many accidents occur today when distant objects or roadway impediments are not quickly detected. To help avoid these accidents, longer-range safety systems are needed with real-time detection capability and without requiring a line-of-sight (LOS) view by the driver or sensor. Early detection at intersections is required for obstacle location around blind corners and dynamic awareness of approaching vehicles on intersecting roadways. Many of today's vehicular safety systems require short LOS distances to be effective. Such systems include forward collision warning, adaptive cruise control, and lane keeping assistance. To operate over longer LOS distances and in Non-LOS (NLOS) conditions, cooperative wireless communications systems are being considered. This paper describes field results for LOS and NLOS radio links for one candidate wireless system: 5.9GHz Dedicated Short Range Communications (DSRC).

In conventional automobile designs, a radiator for cooling the engine and a condenser for condensing the air-conditioner refrigerant are typically configured independently of each other; they are usually mounted in series in the front of the engine compartment so that they will receive sufficient air flow while the vehicle is running. We have developed a smaller and higher performance cooling module by integrating these two heat exchangers into one unit. (Fig 1) For the heat dissipation fin, we have employed an integral fin construction equipped with an insulating slit, resulting in effective prevention of thermal conduction from the higher temperature radiator side, to the condenser side. We also succeeded in improving heat dissipation performance by making effective use of the connection part of the integral fin.

Having a light weight, a good heat conductivity and a good brazability, aluminum alloy is widely used for automotive heat exchanger systems. The major problem with Aluminum is perforation of the tube by pitting corrosion and corrosion protection is necessary in the field. In radiator and condenser systems using the the Nocolok brazing process given good corrosion resistance using cathodic protection with sacrificial anode made of Zn-sprayed onto tube or low corrosion potential fins etc. On the other hand, in drawn-cup type evaporators, that are fabricated from brazing sheet tubes in vacuum brazing method and then covered low electro-conductive drain water film in operation, the effect of cathodic protection by the anode fin is limited to a very small area. Therefore, this has been studied to improve self-corrosion resistance of the core in the brazing sheet tube.

Biofuels are expanding continuously in global market as one of renewable options to replace fossil fuels. Biodiesel is the most commonly used biofuel that can be blended into conventional diesels in any proportion. However, higher biodiesel blends may cause problems. One of its problems is precipitation formation arise from biodiesel may clog fuel filter at low temperature. This study focuses on fuel and environment factors on biodiesel precipitation and their influence degree on fuel filter clogging. The results indicate that monoglycerides and temperature have strong correlation with precipitate weight. Moreover, quantitative effect of precipitate weight on filter clogging was clarified.

In automotive air conditioning, balancing comfort and fuel efficiency is very important. Vehicle cooling performance improvements during initial cool down has reached a limit in recent years, especially in very hot regions. We have addressed this issue by developing a unique double-pipe internal heat exchanger. In the main discourse, we first clarify the concept of the internal heat exchanger system (IHE) using the temperature difference between the high and low pressure pipes in the refrigeration cycle, and propose the application of an efficient internal heat exchanger. This unique double-pipe internal heat exchanger can easily be manufactured by inserting the inner pipe into the outer pipe and by fixing the pipes at both ends. The length of the IHE is 400mm. This double-pipe internal heat exchanger can increase cooling performance by 5-12% at the equivalent power consumption levels in the same space as a conventional front air conditioner system.

For further increase in thermal efficiency of heavy-duty diesel engines, flexible regulation of the heat release rate (HRR) profile combined with higher compression ratio could have more rooms to improve indicated thermal efficiency by overcoming various drawbacks relevant to higher compression ratio. A new ideal HRR profile, which starts as a kind of delta shape to fulfil the isobaric cycle from top-dead-center (TDC) and is followed by the significant increase in HRR to reach the maximum cylinder pressure in the retarded timing, was proposed. We call it as ‘High-heels’ HRR profile from its two-step-increase delta shape. To confirm the potential of the ideal HRR profile by utilizing a single- cylinder heavy-duty diesel engine, a variable fuel injection rate equipment, novel combustion chamber designs, and an offset orifices nozzle were investigated as the technologies for modifying HRR profile.