Search Results

In the automotive industry, the use of beading is widely spread. Beads are primarily used to stiffen the floor and dash panels. The aim is to reduce vibration levels and hopefully at the same time reduce radiated noise. Beading has a positive effect close to the first panel mode's natural frequency however it can have a negative effect at all other frequencies. Typically, engineers assume a radiation efficiency of “1” (one) over the whole frequency range for simplicity or lack of available implemented formulation in their simulation tools. This assumption directs the investigation at reducing the vibration levels only. This approach can be misleading because even though radiation efficiency tends to “1” (one) above coincident frequency it is not the case below coincidence. While increasing stiffness reduces vibration levels, it also increases radiation efficiency. This can yield to higher levels of radiated noise.

The statistical energy analysis (SEA) is widely used to support the development of the sound package of cars. This paper will present the preparation of a model designed to investigate the sound package of the new Audi A3 and associated correlation against measurements. Special care was given during the creation of the model on the representation of the structure to enable the analysis of structure borne energy flow on top of the classical airborne analysis usually done with SEA. The sound package was also detailed in the model to allow further optimization and analysis of its performance. Two real life load cases will be presented to validate the model with measurements. First, the dominating powertrain and a second load case with dominating rolling noise. An analysis of the contribution of the different source components and a way to diagnose the weak paths of the vehicle will be presented. The focus of this investigation is the application of optimally adjusted treatment.

The Finite Element Method (FEM) and the Statistical Energy Analysis (SEA) are standard methods in the automotive industry for the prediction of vibrational and acoustical response of vehicles. However, both methods are not capable of handling the so called “mid frequency problem”, where both short and long wavelength components are present in the same system. A Hybrid method has been recently proposed that rigorously couples SEA and FEM. In this work, the Hybrid FE-SEA method is used to predict interior noise levels in a trimmed full vehicle due to broadband structure-borne excitation from 200Hz to 1000Hz. The process includes the partitioning of the full vehicle into stiff components described with FE and modally dense components described with SEA. It is also demonstrated how detailed local FE models can be used to improve SEA descriptions of car panels and couplings.

The Hybrid FE-SEA method has been used to create a fast/efficient model to predict structure-borne noise propagation in a fully trimmed vehicle over the frequency range from 200 to 1000 Hz. The method was highlighted along with the modeling process and extensive validation results in previously published papers [1-3]. The use of the model to analyze structure-borne noise in the full vehicle, and to design and evaluate the impact of counter measures was described. In this study, the Hybrid FE-SEA method is used identify potential design changes to improve the acoustic performance. First, results from a noise path analysis are used to identify key contributors to interior noise. Next, potential design strategies for reducing the interior noise are introduced along with implications on the model. Finally, sample prediction results illustrating the impact of design changes on interior noise levels are shown along with experimental validation results.

The need for the industry to simulate and optimize the acoustic trim parts has increased during the last decade. There are many approaches to integrate the effect of an acoustic trim in a finite element model. These approaches can be very simple and empirical like the classical non-structural mass (NSM) combined to a high acoustic damping value in the receiver cavity to much more detailed and complex approach like the Poro-Elastic Materials (PEM) method using the Biot parameters. The objective of this paper is to identify which approach is the most appropriate in given situations. This article will first make a review of the theory behind the different methods (NSM, Impedances, Transfer Matrix Method, PEM). Each of them will be investigated for the different typical trim families used in the automotive industry: absorber, spring/mass, spring/mass/absorber.

This paper discusses the development of a computationally efficient numerical method for predicting the acoustics of rattle events upfront in the design cycle. The method combines Finite Elements, Boundary Elements and SEA and enables the loudness of a large number of rattle events to be efficiently predicted across a broad frequency range. A low frequency random vibro-acoustic model is used in conjunction with various closed form analytical expressions in order to quickly predict impact probabilities and locations. An existing method has been extended to estimate the statistics of the contact forces across a broad frequency range. Finally, broadband acoustic radiation is predicted using standard low, mid and high frequency vibro-acoustic methods and used to estimate impact loudness. The approach is discussed and a number of validation examples are presented.

Quality and refinement are of paramount importance for luxury vehicles. The rapid electrification of the automotive industry has increased the contribution of aeroacoustics to the consumer perception of sound quality. The ability to predict whole vehicle aeroacoustic interior noise is essential in the development of vehicles with an extraordinary acoustic environment. This publication summarises the development of a process to combine lattice Boltzmann computational fluid dynamics simulations, with a whole vehicle statistical energy analysis model, to predict the aeroacoustic contribution from all relevant sources and paths. The ability to quantify the relative contribution of glazing panels and path modifications was also investigated. The whole vehicle aeroacoustic interior noise predictions developed, were found to be within 2dB(A) of comparable test vehicle wind tunnel measurements, across a broad frequency range (250-5000 Hz).

Since Statistical Energy Analysis (SEA) is based on lumped parameters, acoustic responses predicted by SEA are spatially discontinuous. However, in many practical applications, the ability to predict spatially continuous energy flow is useful for guiding the design of systems with improved acoustical characteristics. A new approach, utilizing integral equations derived from energy flow concepts, is developed to predict the continuous variation of acoustic field such as sound pressure level in the interior of acoustic domains using structural response predicted by SEA. The computer code developed based on energy flow boundary integral equations is initially validated by analyzing sound propagation in a duct.

Recent developments in the prediction of the contribution of wind noise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This paper discusses in detail these three aspects of wind noise simulation and recommends appropriate methods to deliver required results at the right time based on i) simulation and experimental data availability, ii) design stage and iii) time available to deliver these results. Several simulation methods are used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA.

The need in the automotive industry to understand the physical behavior of trims used in a vehicle is high. The PEM (poro-elastic method) was developed to permit an explicit representation of the trims in the FEM full vehicle models and to give tools to diagnose the effect of the trims and test design changes (porous material property, geometry, etc.,). During the last decade, the evolution of software and hardware has allowed the creation of models with highly detailed trim description (porous material using Biot parameters, plastic trims, etc.,). These models can provide good correlation up to 400Hz compared to measurements in contrast to classical NSM (Non Structural Mass) methodology which shows limitations.

One of the major concerns in the vehicle trim part design is the acoustic targets, which are generally defined by absorption area or coefficients, and sound transmission loss (STL) or sound insertion loss (SIL). The breaking down of acoustic targets in vehicle design, which is generally referred to as cascading, is the process of determining the trim part acoustic targets so as to satisfy full vehicle acoustic performance. In many cases, these targets are determined by experience or by subjective evaluation. Simulation based transfer path analysis (TPA), which traces the energy flow from source, through a set of paths to a given receiver, provides a systematic solution of this problem. Guided by TPA, this paper proposes a component level target setting approach that is based on the statistical energy analysis (SEA), an efficient method for vehicle NVH analysis in mid and high frequencies.

Since the last decade, the automotive industry has expressed the need to better understand how the different trim parts interact together in a complete car up to 400 Hz for structureborne excitations. Classical FE methods in which the acoustic trim is represented as non-structural masses (NSM) and high damping or surface absorbers on the acoustic cavity can only be used at lower frequencies and do not provide insights into the interactions of the acoustic trims with the structure and the acoustic volume. It was demonstrated in several papers that modelling the acoustic components using the poroelastic finite element method (PEM) can yield accurate vibro-acoustic response such as transmission loss of a car component [1,2,3]. The increase of performance of today's computers and the further optimization of commercial simulation codes allow computations on full vehicle level [4,5,6] with adequate accuracy and computation times, which is essential for a car OEM.

Recent developments in the prediction of the contribution of wind noise to the interior SPL have opened a realm of new possibilities. The main physical mechanisms related to noise generation within a turbulent flow and the vibro-acoustic transmission through the vehicle greenhouse is nowadays better understood. Several simulation methods such as CFD, FEM, BEM, FE/SEA Coupled and SEA can be coupled together to represent the physical phenomena involved. The main objective being to properly represent the convective and acoustic component within the turbulent flow to ensure proper computation of the wind noise contribution to the interior SPL of a vehicle.

Wind noise is a major contributor to vehicle noise and a very common consumer complaint for overall vehicle quality [1]. The reduction of wind noise is becoming even more important as powertrain noise is reduced or eliminated (by conversion to hybrid and electric vehicles) and as the importance of quiet interior environment for hands-free device use and voice activation systems becomes more pronounced. In contrast to other noise sources such as tires, engine, intake, exhaust or other component noise whose acoustic loads may be measured in a direct and standardized way with the proper equipment, wind noise is very difficult to predict because the acoustic part of wind noise is a small component of overall fluctuating pressures. It is very challenging to either directly measure or to simulate the acoustic component of fluctuating exterior pressures using CFD (Computational Fluid Dynamics) without a great deal of specialized experience in this area.

Predicting Vehicle Pass-by noise using simulation enables efficient development of adequate countermeasures to meet legislative targets while reducing development time and the number of physical trial-and-error prototypes and tests. It has already been shown that deterministic simulation methods such as the Boundary Element Method (BEM), which may also include directivity of sources, can support the trim package optimization process for Pass-by noise, especially for low to mid frequencies. At higher frequencies, the Ray Tracing technique, can represent an efficient alternate providing options to trade off speed versus accuracy compared to wave-based technique such as FE/BEM. This paper presents a Ray Tracing approach with high order diffraction effect. Moreover, source directivity and sound package effect are accounted for.

Optimizing noise control treatments in the early design phase is crucial to meet new strict regulations for exterior vehicle noise. Contribution analysis of the different sources to the exterior acoustic performance plays an important role in prioritizing design changes. A method to predict Pass-by noise performance of a car, based on source-path-receiver approach, combining data coming from simulation and experimental campaigns, is presented along with its validation. With this method the effect of trim and sound package on exterior noise can be predicted and optimized.

Designing an effective AVAS system, not only to meet safety regulations, but also to create the expected perception for the vulnerable road user, relies on knowledge of the acoustic transfer function between the sound actuator and the receiver. It is preferable that the acoustic transfer function be as constant as possible to allow transferring the sound designed by the car OEM to ensure the safety of vulnerable road users while conveying the proper brand image. In this paper three different methodologies for the acoustic transfer function calculations are presented and compared in terms of accuracy and calculation time: classic Boundary Element method, H-Matrix BEM accelerated method and Ray tracing method. An example of binaural listening experience at different certification positions in the modeled simulated space is also presented.

This paper presents an integrated simulation process which has been performed in order to assess the riding comfort performance of a vehicle seat system virtually. Present methods of seat comfort design rely on the extensive testing of numerous hardware prototypes. In order to overcome the limitations of this expensive and time-consuming process, and to fasten innovation, simulation-based design has to be used to predict the seat comfort performance very early in the seat design process, leading to a drastic reduction in the number of physical prototypes. The accurate prediction of the seat transfer function by numerical simulation requires a complete simulation chain, which takes into account the successive stages determining the final seat behaviour when submitted to vibrations. First the manufacturing stresses inside the cushion, resulting from the trimming process, are computed.

The development of an effective Acoustic Vehicle Alert System (AVAS) is not solely about adhering to safety regulations; it also involves crafting an auditory experience that aligns with the expectations of vulnerable road users. To achieve this, a deep understanding of the acoustic transfer function is essential, as it defines the relationship between the sound emitter (the speaker inside the vehicle) and the receiver (the vulnerable road user). Maintaining the constancy of this acoustic transfer function is paramount, as it ensures that the sound emitted by the vehicle aligns with the intended safety cues and brand identity that is defined by the car manufacturer. In this research paper, three distinct methodologies for calculating the acoustic transfer function are presented: the classical Boundary Element method, the H-Matrix BEM accelerated method, and the Ray tracing method.

To meet vehicle interior noise targets and expectations, components including those related to electric vehicles (EVs) can effectively be treated at the source with an encapsulation approach, preventing acoustic and vibration sources from propagating through multiple paths into the vehicle interior. Encapsulation can be especially useful when dealing with tonal noise sources in EVs which are common for electrical components. These treatments involve materials that block noise and vibration at its source but add weight and cost to vehicles – optimization and ensuring the material used is minimized but efficient in reducing noise everywhere where it is applied is critically important. Testing is important to confirm source levels and verify performance of some proposed configurations, but ideal encapsulation treatments are complex and cannot be efficiently achieved by trial-and-error testing.