Search Results

Electronic Stop-Start (ESS) system automatically stops and restarts the engine to save energy, improve fuel economy and reduce emissions when the vehicle is stationary during traffic lights, traffic jams etc. The stop and start events cause unwanted vibrations at the seat track which induce discomfort to the driver and passengers in the vehicle. These events are very short duration events, usually taking less than a second. Time domain analysis can help in simulating this event but it is difficult to see modal interactions and root cause issues. Modal transient analysis also poses a limitation on defining frequency dependent stiffness and damping for multiple mounts. This leads to inaccuracy in capturing mount behavior at different frequencies. Most efficient way to simulate this event would be by frequency response analysis using modal superposition method.

Automotive companies are studying to add extra value in their vehicles by enhancing powertrain sound quality. The objective is to create a brand sound that is unique and preferred by their customers since quietness is not always the most desired characteristic, especially for high-performance products. This paper describes the process of developing a brand powertrain sound for a high-performance vehicle using the DFSS methodology. Initially the customer's preferred sound was identified and analyzed. This was achieved by subjective evaluations through voice-of-customer clinics using vehicles of similar specifications. Objective data were acquired during several driving conditions. In order for the design process to be effective, it is very important to understand the relationship between subjective results and physical quantities of sound. Several sound quality metrics were calculated during the data analysis process.

Automobiles have a high degree of mechanical and electrical complexity. However, product complexity has the accompanying effect of requiring high levels of design and process oversight. The net result is a product creation process which is prone to creating failures. These failures typically have their origin in an overall lack of complete understanding of the system in terms of materials, geometries and energy flows. Despite all of the engineering intentions, failures are inevitable, common, and must be dealt with accordingly. In the worst case, if a failure manifests itself into an observable failure the customer may have a negative experience. Therefore, it is imperative that design engineers, suppliers along with reliability professionals be able to assess the design risk. One approach to assess risk is the use of degradation analysis. Degradation analysis often provides more information than failure time data for assessing reliability and predicting the remnant life of a system.

Engine air induction shell noise is a structure borne noise that radiates from the surface of the air induction system. The noise is driven by pulsating engine induction air and is perceived as annoying by vehicle passengers. The problem is aggravated by the vehicle design demands for low weight components packaged in an increasingly tight under hood environment. Shell noise problems are often not discovered until production intent parts are available and tested on the vehicle. Part changes are often necessary which threatens program timing. Shell noise should be analyzed in the air induction system design phase and a good shell noise analytical process and targets must be defined. Several air induction clean side ducts are selected for this study. The ducts shell noise is assessed in terms of material strength and structural stiffness. A measurement process is developed to evaluate shell noise of the air induction components. Noise levels are measured inside of the clean side ducts.

Multiaxial loading on mechanical products is very common in the automotive industry, and how to design and analyze these products for durability becomes an important, urgent task for the engineering community. Due to the complex nature of the fatigue damage mechanism for a product under multiaxial state of stresses/strains which are dependent upon the modes of loading, materials, and life, modeling this behavior has always been a challenging task for fatigue scientists and engineers around the world. As a result, many multiaxial fatigue theories have been developed. Among all the theories, an existing equivalent stress theory is considered for use for the automotive components that are typically designed to prevent Case B cracks in the high cycle fatigue regime.

Threaded fasteners or bolted joints are used extensively in automotive assemblies. There are standard procedures to evaluate joint performance under block cycles or road loads. The deciding load case for such joint design is slippage analysis of the joint. There are studies done to evaluate the theoretical and experimental behavior of these joints. There are different ways of understanding the interaction between the bolt and the nut under different loading scenarios. However, none have provided a satisfactory method of quantifying bolt loosening or loss of clamp load under cyclic loading, where no slippage is observed. Under varying loads, initial relaxation of the joint is followed by a loss of clamping load. Below a critical value, complete loss of clamping load progresses very rapidly and this results in a loose joint.

This paper describes an experimental study on the performance of self-piercing riveted (SPR) joints and adhesively bonded SPR joints connecting steel and aluminum components under both quasi-static and cyclic loading. The joint configurations cover a wide range of material gauges, types and grades. Two and three thickness joints, with and without adhesive are also part of this study. Load versus deflection behavior, load carrying capacity, fatigue life and the failure modes for each type of joint are discussed. This study focuses on the influence of dissimilar material and adhesives to the joint performance.

Geometry Tree is a term describing the product assembly structure and the manufacturing process for the product. The concept refers to the assembly structure of the final vehicle (the Part Tree) and the assembly process and tools for the final product (the Process Tree). In the past few years, the Geometry Tree-based quality process was piloted in the FCA US LLC assembly plants and has since evolved into a standardized quality control process. In the Part Tree process, the coordinated measurements and naming convention are enforced throughout the different levels of detailed products to sub-assemblies and measurement processes. The Process Tree, on the other hand, includes both prominently identified assembly tools and the mapping of key product characteristics to key assembly tools. The benefits of directly tying critical customer characteristics to actual machine components that have a high propensity to influence them is both preventive and reactive.

Vehicle suspension parts are subjected to variable road loads, manufacturing process variation and high installation loads in assembly process. These parts must be robust to usage conditions to function properly in the field. Design for Six Sigma (DFSS) tools and Taguchi Method were used to optimize initial rear suspension trailing arm design. Project identified key control factor/design parameters, to improve part robustness at the lowest cost. Optimized design performs well under higher road loads and meets stringent durability requirements. This paper evokes use of Taguchi Method to design robust rear suspension trailing arm and study effect of selected design parameters on robustness, stress level/durability and part cost.

The latest trend in transmission hydraulic controls development ise body integrated direct acting control solenoid, ted by multiple automotive OEMs. The advantages of integrated direct acting control solenoids are key enablers for OEMs to meet more and more stringent fuel economy requirement and competitive environment. In the meantime, there are unique challenges in both designing and manufacturing of such solenoids, due to the fact the solenoid armature can only push the spool valve with limited force and limited stroke. Through analytical methods, this paper explains design guidelines to overcome the challenges and quantifies the impact of design decision to critical functional objectives. Multiple valve design configurations, including both normally low and normally high functionality, are covered in the analysis. Unique manufacturing process concerns are also addressed.

This paper describes a study on identifying a suitable thickness for finite element modeling a “deformable washer” to simulate bolted joints for vehicle level durability analysis based on experimental results. First, a test matrix table is introduced, which is based on representative vehicle structures for different bolt/nut sizes, bolt grades, sheet gages, and sheet materials etc. Then coupon tests, both static and fatigue, are illustrated. Next, the corresponding finite element model with different thickness of “deformable washers” and results are presented. Following that, the optimal “deformable washer” thickness is recommended based on statistical parameters (mean and standard deviation) of the relative differences between finite element analysis results and physical test results. Lastly, a case study is demonstrated for the proposed strategy.

This paper describes a laboratory-based test system and procedure for determining the durability of RTV sealant with fretting movement. A test machine is described in which shear and tensile stress-generating displacements at room temperature and temperature of 100°C are produced to load an RTV seal. The test system utilizes an air pressurized hollow cylinder with a cap sealed by RTV sealant on a reciprocating test rig. An external air leakage monitoring system detects the health of the tested RTV seal. When air leakage occurs, the seal is determined to have failed. RTV sealant used in the test was fully cured at room temperature and then aged with engine oil. In the experiments, a total of 6 displacements were used to generate cycle/amplitude graphs for both shear and tensile modes. Failures were determined to be caused by the loss of adhesion in tensile mode, and by crack nucleation due to the special step design in shear mode.

Advanced high strength steels (AHSS) have been extensively used in the automotive industry for vehicle weight reduction. Although AHSS show better parent metal fatigue performance, the influence of material strength on spot weld fatigue is insignificant. To overcome this drawback, structural adhesive can been used along with spot weld to form weld-bond joints. These joints significantly improve spot weld fatigue performance and provide high joint stiffness enabling down-gauge of AHSS structures. However, modeling the adhesive joints using finite element methods is a challenge due to the nonlinear behavior of the material. In this study, the formulation of cohesive element based on the traction-separation constitutive law was applied to predict the initiation and propagation of the failure mode in the adhesively bonded joints for lap shear and coach peel specimens subjected to quasi-static loadings. The predicted load versus displacement relations correlated well with the test results.

For many automotive systems it is required to calculate both the durability performance of the part and to rule out the possibility of collision of individual components during severe base shake vibration conditions. Advanced frequency domain methods now exist to enable the durability assessment to be undertaken fully in the frequency domain and utilizing the most advanced and efficient analysis tools (refs 1, 2, 3, 4, 5). In recent years new capabilities have been developed which allow hyper-sized models with multiple correlated loadcases to be processed. The most advanced stress processing (eg, complex von-Mises) and fatigue algorithms (eg, Strain-Life) are now included. Furthermore, the previously required assumptions that the loading be stationary, Gaussian and random have been somewhat relaxed. For example, mixed loading like sine on random can now be applied.

A vehicle’s exterior fit and finish, in general, is the first system to attract customers. Automotive exterior engineers were motivated in the past few years to increase their focus on how to optimize the vehicle’s exterior panels split lines quality and how to minimize variation in fit and finish addressing customer and market required quality standards. The design engineering’s focus is to control the deviation from nominal build objective and minimize it. The fitting process follows an optimization model with the exterior panel’s location and orientation factors as independent variables. This research focuses on addressing the source of variation “contributed factors” that will impact the quality of the fit and finish. These critical factors could be resulted from the design process, product process, or an assembly process. An empirical analysis will be used to minimize the fit and finish deviation.

Dimensional accuracy of punched hole is an essential consideration for high-quality sheet metal forming. An out-of-shape hole can give rise to manufacturing issues in the subsequent production processes thus inducing quality defects on a vehicle body. To understand the effects of punch shapes and cutting configurations on punched hole diameter deviations, a systematical experimental study was conducted for multiple types of AHSS (DP1180, DP980, DP590) and one mild steel. Flat, conical and rooftop punches were tested respectively with three cutting clearances on each material. The measurement results indicated different diameter enlargement modes based on the punch profiles, and dimensional discrepancies were found to be more significant with the stronger materials and higher cutting clearance. To uncover the mechanism of punched hole enlargement, a series of finite element simulations were established for numerical investigation.

The complexities involved in an optimization problem at a system level require knowledge base that has information on different approaches and customization of these approaches to a specific class of the optimization problems. One approach that is commonly used is the metamodel based design optimization. The metamodel is 1) a conceptual model for capturing, in abstract terms, essential characteristics of a given optimization problem, and 2) a schema of sufficient formality to enable the problem modeled to be serialized to statements in a concrete optimization language [1]. Optimization is performed based on this metamodel. This metamodel approach has been proven effective and accurate in providing the global optimum. Depending upon the computational hardware availability in an organization, the metamodel based optimization could be much faster way of achieving the optimized solution. However, the accuracy of the optimization is highly dependent on the quality of metamodel generated.

In today’s automotive industry, the A/C (Air-conditioning) system is emerging into a high level of technological growth to provide quick cooling, warm up and maintaining the air quality of the cabin during all-weather conditions. In HVAC system, TXV plays vital role by separating high side to low side of vapor compression refrigeration system. It also regulates the amount of refrigerant flow to the evaporator based on A/C system load. The HVAC system bench laboratory conducts the test at different system load conditions to evaluate the outputs from tests during initial development stage to select the right TXV in terms of capacity and Superheat set point for a given system. This process is critical in HVAC developmental activity, since mule cars will be equipped with selected TXV for initial assessment of the system performance.

Due to increasing standards in fuel consumption, battery electric vehicles (BEV) and plug in electric hybrid vehicles (PHEV), are becoming more commonplace in the automotive industry. Batteries used in such applications require methods of thermal management to promote longer life, higher efficiency and performance. A common method of keeping the battery cool, in high heat conditions, is to use a water to refrigerant chiller. The already existing automotive air conditioning system is leveraged to enable the use of such a chiller. The added thermal transient load of the battery adds complexity to the refrigeration system. Balancing the thermal comfort of the occupants with temperature requirements of battery drives challenges to the overall system capacity. The sudden change in battery cooling loads can noticeably degrade the evaporator heat rejection. In extreme cases the battery cooling load can cause complete loss of refrigerant flow to the evaporator.

There is an increasing demand for reducing vehicle development process and minimizing cost due to tough competition in Automotive market. One of the major focus areas is minimizing the vehicle proto build that are required for physical testing during vehicle development. Tow hooks are key structural components for the vehicle, which are designed to withstand structural strength performance under various vehicles towing condition. Typical extreme load scenario for the vehicle can be towing fully loaded vehicle breaks down on uphill road or stuck in wet muddy condition. To exercise the tow hook structural development in early design phase, it is important to have reliable simulation process. This paper focuses on development of virtual test simulation process that replicates the tow hook system test behavior for the operating load. The study includes the detail modeling of clevis load applicator, tow hook, bolt joint and attached test bed plate for capturing the load path.