Search Results

Internal combustion engine gets heated up due to continuous combustion of fuel. To keep engine working efficiently and prevent components damage due to very high temperature, the engine needs to be cooled down. Based on power output requirement and provision for cooling system, every engine has it’s unique cooling system. Liquid based cooling systems are majorly implemented in automobile. It’s important to keep in mind that during design phase that, cooling the engine will lower the power to fuel consumption ratio. Therefore, during lower ambient conditions, the cooling system should be able to uniformly increase the temperature of the engine components, engine oil and transmission oil. This is achieved by circulating the coolant through cooling jacket, engine oil heater and transmission oil heater, which will be heated by the combustion heat.

In the NVH domain, the cooling module is an important subsystem in ground vehicles. Recently, with the development of small high output turbocharged internal combustion (IC) engines, cooling module noise and vibration has become more challenging. Furthermore, with plug-in hybrid electric vehicle (PHEV), in some cases the cooling fan could be operational while the IC engine is not running. This poses a significant challenge for cabin noise enhancement. Small turbocharged IC engines typically require higher cooling capacity resulting in larger fan size designs with higher speed. Accurate prediction of the unbalance loads generated by cooling fan and loads transferred to the body are critical for the Noise Vibration and Harshness (NVH) performance of the vehicle. If the NVH risk of cooling module operation is not well quantified and addressed early in the program, attempts to find solutions in post launch stage could be very expensive and not as effective.

There are many noise sources from the vehicle fuel system to generate noise inside a vehicle. Among them, the pressure pulsation due to the rapid opening and closing of gasoline engine injectors can cause undesirable fuel pulse noise. As the pressure pulsation propagates in the fuel supply line toward to rear end of the vehicle, the pressure energy is transferred from fuel lines to the vehicle underbody through clips and into the passenger compartment. It is crucial to attenuate the pressure pulsation inside the fuel line to reduce the fuel pulse noise. In this paper, a case study on developing an effective countermeasure to reduce the objectionable fuel pulse noise of a V8 gasoline injection system at engine idle condition is presented. First, the interior noise of a prototype vehicle was tested and the objectionable fuel pulse noise is exhibited. The problem frequency ranges of the pulse noise were identified.

Maintaining the fuel temperature and fuel system components below certain values is an important design objective. Predicting these temperatures is therefore one of the key parts of the vehicle’s thermal management process. One of the physical processes affecting fuel tank temperature is fuel vaporization, which is controlled by the vapor pressure in the tank, fuel composition and fuel temperature. Models are developed to enable the computation of the fuel temperature, fuel vaporization rate in the tank, fuel temperatures along the fuel supply lines, and follow its path to the charcoal canister and into the engine intake. For diesel fuel systems where a fuel return line is used to return excess fluid back to the fuel tank, an energy balance will be considered to calculate the heat added from the high-pressure pump and vehicle under-hood and underbody.

In Automotive and Aerospace industries, sound package has an important role to control vehicle noise in order to improve passenger comfort and reduce environmental noise pollution. The most known approaches used to model the sound package are the Transfer Matrix Method (TMM) combined with Statistical Energy Analysis (SEA). The Transfer Matrix Method based approach is extensively used and well-validated for predicting the transmission loss and other vibro-acoustic indicators of multi-layer structures. However, to the best of our knowledge, the equivalent damping due to the multilayer has not been addressed yet in the literature, and it's a novel approach. In this paper, simplified formulations using TMM to compute the equivalent damping will be recalled, and an experimental study will be conducted to assess the add-on damping by sound package for different configurations.

The performance and durability of the lead acid battery is highly dependent on the internal battery temperature. The changes in internal battery temperatures are caused by several factors including internal heat generation and external heat transfer from the vehicle under-hood environment. Internal heat generation depends on the battery charging strategy and electric loading. External heat transfer effects are caused by customer duty cycle, vehicle under-hood components and under-hood ambient air. During soak conditions, the ambient temperature can have significant effect on battery temperature after a long drive for example. Therefore, the temperature rise in a lead-acid battery must be controlled to improve its performance and durability. In this paper a thermal model for lead-acid battery is developed which integrates both internal and external factors along with customer duty cycle to predict battery temperature at various driving conditions.

In this paper we present an integrated approach which combines analysis of the effect of simultaneous variations in model input parameters on component or system temperatures. The sensitivity analysis can be conducted by varying model input parameters using specific values that may be of interest to the user. The alternative approach is to use a structured set of parameters generated in the form of a DFSS DOE matrix. The matrix represents a combination of simulation conditions which combine the control factors (CF) and noise factors. CF’s are the design parameters that the engineer can modify to achieve a robust design. Noise factors include parameters that are outside the control of the design engineer. In automotive thermal management, noise factors include changes in ambient temperature, exhaust gas temperatures or aging of exhaust system or heat shields for example.

Determining coolant flow distribution in a topologically complex flow path for efficient heat rejection from the critical regions of the engine is a challenge. However, with the established computational methodology, thermal response of an engine (via conjugate heat transfer) can be accurately predicted [1, 2] and improved upon via Design of Experiment (DOE) study in a relatively short timeframe. This paper describes a method to effectively distribute the coolant flow in the engine coolant cavities and evenly remove the heat from various components using a novel technique of optimization based on an approximation model. The current methodology involves the usage of a sampling technique to screen the design space and generate the simulation matrix. Isight, a process automation and design exploration software, is used to set the framework of this study with the engine thermal simulation setup done in the CFD solver, STAR-CCM+.

Significant reduction in Nitrogen Oxide (NOx) emissions will be required to meet LEV III/Tier III Emissions Standards for Light Duty Diesel (LDD) passenger vehicles. As such, Original Equipment Manufacturers (OEMs) are exploring all possible aftertreatment options to find the best balance between performance, durability and cost. The primary technology adopted by OEMs in North America to achieve low NOx levels is Selective Catalytic Reduction (SCR). The critical parameters needed for SCR to work properly are: an appropriate reductant such as ammonia (NH3) provided as Diesel Exhaust Fluid (DEF), which is an aqueous urea solution 32.5% concentration in weight with water (CO(NH2)2 + H2O), optimum operating temperatures, and optimum nitrogen dioxide (NO2) to NOx ratios (NO2/NOx). The NO2/NOx ratio is most influenced by Precious Group Metals (PGM) containing catalysts upstream of the SCR catalyst.

Engine mount is one of the temperature sensitive components in the vehicle under-hood. Due to increasing requirements for improved fuel economy, the under-hood thermal management has become very challenging in recent years. In order to study the effects of material thermal degradation on engine mount performance and durability; it is required to estimate the temperature of engine mount rubber during various driving conditions. The effect of temperature on physical properties of natural rubber can then be evaluated and the life of engine mount can be estimated. In this paper, a bench test is conducted where the engine mount is exposed to a step change in the environment around it, and the temperature of the rubber section is recorded at several points till a steady state temperature is reached. A time response curve is generated, from which a time constant is determined.

Engine air induction shell noise is a structure borne noise that radiates from the surface of the air induction system. The noise is driven by pulsating engine induction air and is perceived as annoying by vehicle passengers. The problem is aggravated by the vehicle design demands for low weight components packaged in an increasingly tight under hood environment. Shell noise problems are often not discovered until production intent parts are available and tested on the vehicle. Part changes are often necessary which threatens program timing. Shell noise should be analyzed in the air induction system design phase and a good shell noise analytical process and targets must be defined. Several air induction clean side ducts are selected for this study. The ducts shell noise is assessed in terms of material strength and structural stiffness. A measurement process is developed to evaluate shell noise of the air induction components. Noise levels are measured inside of the clean side ducts.

Piston temperature plays a major role in determining details of fuel spray vaporization, fuel film deposition and the resulting combustion in direct-injection engines. Due to different heat transfer properties that occur in optical and all-metal engines, it becomes an inevitable requirement to verify the piston temperatures in both engine configurations before carrying out optical engine studies. A novel Spot Infrared-based Temperature (SIR-T) technique was developed to measure the piston window temperature in an optical engine. Chromium spots of 200 nm thickness were vacuum-arc deposited at different locations on a sapphire window. An infrared (IR) camera was used to record the intensity of radiation emitted by the deposited spots. From a set of calibration experiments, a relation was established between the IR camera measurements of these spots and the surface temperature measured by a thermocouple.

An engine exhaust manifold undergoes repeated thermal expansion and contraction due to temperature variation. Thermomechanical fatigue (TMF) arises due to the boundary constraints on thermal expansion so that mechanical strain is introduced. Therefore, TMF evaluation is very important in engine design. In this work, the mechanical properties important for TMF assessment and modeling of a silicon (Si)- and molybdenum (Mo)-containing ductile cast iron used for exhaust manifold have been evaluated. Tensile, creep, isothermal low cycle fatigue (LCF), and TMF tests have been conducted. Parameters for material modeling, such as the viscoplastic constitutive model and the Neu-Sehitoglu TMF damage model, have been calibrated, validated, and used to evaluate the TMF life of the exhaust manifold.

This paper will explore the effect that non-constant function CD (as observed during wind tunnel testing) would have on the coastdown derived drag coefficient and other regulatory drive cycles. It is common in wind tunnel testing to observe road vehicle drag coefficients that vary with speed. These varying CD values as a function of velocity will be expressed as CD(V) in this paper. Wind tunnel testing for product development is generally conducted at 110 km/h (68.3 mph) which are similar speeds and typical of the United States (US), European, and Asian highway speeds. Reported values of CD are generally gathered at these speeds. However, coastdown testing by definition takes place over a large range of speeds mostly lower than the wind tunnel test speeds. This paper will explore the effect that six typical functions of CD(V) have on the coastdown derived CD. One of the six functions is a constant, to represent a wind tunnel reported CD.

The trend to simultaneously improve fuel economy and engine performance has led to industry growth of turbocharged engines and as a result, the need to address their undesirable airborne noise attributes. This presents some unique engineering challenges as higher customer expectations for Noise Vibration Harshness (NVH), and other vehicle-level attributes increase over time. Turbocharged engines possess higher frequency noise content compared to naturally aspirated engines. Therefore, as an outcome, whoosh noise in the Air Induction System (AIS) during tip in conditions is an undesirable attribute that requires high frequency attenuation enablers. The traditional method for attenuation of this type of noise has been to use resonators which adds cost, weight and requires packaging space that is often at a premium in the under-hood environment.

One of the key inputs 1-D transient simulation takes is a detailed front end cooling flow map. These maps that are generated using a full vehicle Three-dimensional Computational Fluid Dynamics (3D CFD) model require expensive computational resources and time. This paper describes how an adaptive sampling of the design space allowed the reduction of computational efforts while keeping desired accuracy of the analysis. The idea of the method was to find a pattern of Design of Experiments (DOE) sampling points for 3D CFD simulations that would allow a creation of an approximation model accurate enough to predict output parameter values in the entire design space of interest. Three procedures were implemented to get the optimal sampling pattern.

As automotive emissions become more stringent, accurate control of three-way catalyst temperature is increasingly important for maintaining high levels of conversion efficiency as well as preventing damage to the catalyst. A real-time catalyst temperature model provides critical information to the engine control system. In order to improve emissions and ensure regulatory compliance over a wide range of speed-load conditions, it is desirable to use modelled catalyst temperature as the primary input to catalyst efficiency control strategies. This requirement creates a challenge for traditional empirical models designed for component protection at high speed-load conditions. Simulation results show that a physics aligned model can estimate temperature in all operating conditions, including: cold-start, extended idle, engine shutdown, stop-start events, deceleration fuel shut-off, as well as traditional high load and part load points.

This paper describes a reliable CAE methodology to model the linear vibratory behavior of windshields. The windshield is an important component in vehicle NVH performance. It plays an integral role in interior cabin noise. The windshield acts as a large panel typically oriented near vertical at the front of vehicle’s acoustic cavity, hence modeling it accurately is essential to have a reliable prediction of cabin interior noise. The challenge to model the windshield accurately rises from the structural composition of different types of windshields. For automotive applications, windshields come in several structural compositions today. In this paper, we will discuss two types of windshield glass used primarily by automotive manufacturers. First type is the typical laminated glass with polyvinyl butyral (PVB) layer and second type is the acoustic glass with PVB and vinyl layers. Acoustic glass improves acoustic characteristics of the glass in a frequency range of ~ 1200 Hz to ~4000 Hz.

Acoustic comfort of automotive cabins has progressively become one of the key attributes of passenger comfort within vehicle design. Wind noise and the heating, ventilation, and air conditioning (HVAC) system noise are two of the key contributors to noise levels heard inside the car. The increasing prevalence of hybrid technologies and electrification has an associated reduction in powertrain noise levels. As such, the industry has seen an increasing focus on understanding and minimizing HVAC noise, as it is a main source of noise in the cabin particularly when the vehicle is stationary. The complex turbulent flow path through the ducts, combined with acoustic resonances can potentially lead to significant noise generation, both broadband and tonal.

In this study, a unique multi-camera three-dimensional digital image correlation (3D-DIC) system was designed and applied to an engine dynamometer cell to measure the displacement and strain of the exhaust manifold while an engine was running in a durability test. In the engine dynamometer cell, the ambient temperature varies from 25°C to 80°C~100°C cyclically and the exhaust manifold experiences high temperatures up to 900°C with high frequency vibrations. In order to obtain reliable data under such conditions, two 3D-DIC systems were designed and set up in the engine dynamometer. One is a high-speed 3D-DIC system, consisting of cameras with a sampling rate of 1250 frames per second. It was used to measure the local displacement of the bolted joint in the exhaust manifold. The high-speed measurement system is able to record the behavior of the bolt during the thermal cycles.