Search Results

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

Recent investigations by others have indicated that the dynamic response of automotive brake rotors in the squeal frequency range involves the classic flexural modes as well as in-plane motion. While the latter set creates primarily in-plane displacements, there is coupling to transverse displacements that might produce vibrational instabilities. This question is investigated here by analyzing a modal model that includes two modes of the rotor and two modes of the pad and caliper assembly. Coupling between in-plane and transverse displacements is explicitly controlled. Results from this model indicate that the coupling does create vibrational instabilities. The instabilities, whose frequencies are in the squeal range, are characterized by power flow through the transverse motion of the rotor.

All automotive brake linings have mechanical strength and thermal expansion properties which vary with orientation. This paper describes laboratory equipment and test procedures which characterize lining strength and expansion behavior, using small specimens. A benchtop testing device is introduced which can be used to perform shear and tensile tests on lining samples and singly-riveted lining assemblies. Results are presented for a representative group of production and experimental linings. Applications are discussed.

Pyrolytic gas chromatography (PGC) has been applied to the characterization of the organic constituents of brake linings. The test involves the pyrolysis of a sample followed by the instrumental separation and sensing of the products of decomposition. A study of experimental variables, such as pyrolysis temperature, has allowed the selection of conditions which yield excellent reproducibility and sensitivity. The preferred test conditions, which have been incorporated in Ford's brake lining quality control specifications, result in a relatively rapid, meaningful test for constancy of composition.

An experimental modal model of an early prototype car was constructed and validated against test results. The model was then used to suggest practical hardware modification alternatives which would: (1) shift the steering column resonant frequency away from the idle range, and (2) maintain a low steering column tip vibration within the 600-750 RPM idle range. This model was also used to evaluate the effectiveness of tuning radiator mounts to the overall vehicle idle quality. It was found that a pair of braces from either the steering column bracket to brake pedal bracket or to the cowl top area could improve idle shake of the test vehicle. The driver side brake pedal brace alone is not effective. However, the passenger side brake pedal brace alone is as effective as the two brake pedal braces together. It was found that the radiator mounts on the test vehicle are extremely non-linear. Therefore, tuning the mount to improve idle quality is impractical.

During the development of a new friction material, besides the interface between lining/drum is also fundamental take in account all aspects involving the attachment of the linings on the brake shoes. This paper presents an optimization approach to the development and manufacturing parameters of brake linings, applied on medium and heavy duty commercial vehicles, aiming to assure the correct specification of the riveted joint clamp forces. These evaluations were conducted based on the quality tools documents and the theoretical aspects of the product usage as well as the modeling of key elements of the referred mechanism throughout various known applications. A calculation methodology was developed based on brake geometry, its generated forces and braking reactions required for each vehicle family.

Modern project management including brake testing includes the exchange of reliable results from different sources and different locations. The ISO TC22/SWG2-Brake Lining Committee established a task force led by Ford Motor Co. to determine and analyze root causes for variability during dynamometer brake performance testing. The overall goal was to provide guidelines on how to reduce variability and how to improve correlation between dynamometer and vehicle test results. This collaborative accuracy study used the ISO 26867 Friction behavior assessment for automotive brake systems. Future efforts of the ISO task force will address NVH and vehicle-level tests. This paper corresponds to the first two phases of the project regarding performance brake dynamometer testing and presents results, findings and conclusions regarding repeatability (within-lab) and reproducibility (between-labs) from different laboratories and different brake dynamometers.

Chapters written by professional and academic experts in the field cover: analytical modeling and analysis, CEA modeling and numerical methods, techniques for dynamometer and road test evaluation, critical parameters that contribute to brake squeal, robust design processes to reduce/prevent brake squeal via up-front design, and more.