Search Results

While the engine mount rates need to be optimized to achieve the required frequency alignment and modal decoupling for quality performance, the robustness of the system needs to be studied as well. If a system exhibits acceptable modal characteristics with nominal optimized rates, the sensitivity of the system to variation of the rates from their nominal values affects the robustness of the system. Different factors can cause variation of the rates. Among them are rate changes from part to part arising from manufacturing process. In this paper the effect of mount rates variability on the modal characteristics is discussed. Monte Carlo simulation is used to predict how the rigid body modes and their couplings vary when the rate for each mount changes according to its statistical parameters. Through different examples the statistical variability of the modes to the rates variability is presented.

Urea SCR is an established method to reduce NOx in dilute exhaust gas. The method is being used currently with stationary powerplants, and successful trials on motor vehicles have been conducted. The reason most often cited for rejecting urea SCR is lack of urea supply infrastructure, yet urea and other high nitrogen products are traded as commodities on the world market as a fertilizer grade, and an industrial grade is emerging. For a subset of commercial vehicles, urea can be provided by service personnel at designated terminals. But this approach does not support long distance carriers and personal use vehicles. The preferred delivery method is to add urea during vehicle refueling through a common fuel nozzle and fill pipe interface: urea / diesel co-fueling. Aqueous urea is well suited to delivery in this fashion.

Usually in Computer Aided Engineering (CAE) analyses, Computer Aided Design (CAD) data is meshed and analyzed with regard to displacements and stresses. So far, it is not common to account for residual stresses due to the manufacturing process in these analyses. This work proposes a methodology based on simplified abaqus Standard/Explicit models to evaluate residual stresses due to stamping and bending manufacturing process in truck rails and suggests a methodology to use this residual stress data in truck frame CAE durability analysis making it possible to compare how different a predicted fatigue life can be when residual stresses are considered.

Commercial vehicles are being developed for long decades in Brazil creating a deep background on manufacturing process. With the current scenario a variety of different vehicles specifications (weight capacity, load distribution, torque, size, etc.) are being required by the market. Joints with bolts and nuts are the engineering solution for the most of the problems found in automotive engineering regarding commercial vehicles. Screw processes were made during the last 150 years. Nowadays current frame modifications on aftermarket are made with arc weld process that affects directly the material properties and the process needs to be performed by critical personal with training and capacity. In addition cost and timing does not fit for the best equation on how to proceed with the modifications. The solution proposed brings more flexibility on frame assemblies that can be extended to other products.

To meet stringent 2010 NOx emissions, many manufacturers are expected to deploy urea selective catalytic reduction systems. Indications from ARB are that a threshold monitor must be developed to monitor their performance. The most capable monitoring technology at this time relies on NOx sensors. This paper assesses the capability of the NOx sensor as an SCR monitoring device. To this end, the NOx sensor must be able to distinguish between a marginal and a threshold catalyst with enough separation to allow for variability. We present the noise factors associated with the NOx conversion of the SCR system, and analyze what NOx sensor accuracy we need to preserve separation in the face of those noise factors. It is shown that a 1.75 threshold monitor is not feasible with current NOx sensor technology. We analyze the benefit of a partial volume monitor, and show there is no advantage unless the slope error of the NOx sensor is drastically reduced from current levels.

In order to optimize the development of bolted joints used to components attachments in the Sidemember of commercial vehicles, the joints development has become relevant to better definition of the fasteners size, eliminating overweight and avoiding under or super-sized. This paper presents a development sequential approach of bolted joints applied on commercial vehicles ensuring the correct specifications usage of the fasteners and the joint to keep their clamp force. The evaluations were conducted based on theoretical and practical aspects applied on products and in the definition of all elements contained in a joint. The calculation methodology was developed based on standardized bolts and forces generated through the reactions of the components required for each vehicle family.

Hydroformed truck frame side rails from circular tubes are studied for gage variations and pre-strain to be used in crash FEA modeling practice. This study provides simplified models that achieve feasible correlation with actual tests. Meanwhile, from plasticity theory we derive a forming equation in conjunction with forming limit diagrams to estimate material properties for hydroformed rails.

Recent accomplishments, made possible by advances in manufacturing and material technology, have led to the development of a one-piece stamped I-Beam axle with ball joints as a replacemet to the forged axle with king pin design. The new stamped I-Beam axle brings with it a number of improvements to Ford's Twin I-Beam suspension system. This paper describes the objectives, improvements, evolution of the design, testing, and the manufacturing process for this latest suspension system improvement on Ford light trucks.

Ford's continued effort to improve fuel economy in automotive applications has emphasized the need for lightweight components that retain all the toughness associated with Ford truck vehicle characteristics. The application of an impact extrusion process to wheel design and manufacture, for Ford Aerostar, provides strength, performance and style more efficiently than other traditional processes. It results in a valuable 33% weight saving over comparable HSLA steel wheels, and provides the customer with uncompromised value. The Ford Aerostar Impact Extruded Aluminum Wheel was designed to be of one-piece construction, manufactured from a less than 1″ thick aluminum wafer-shaped blank. The process permits manufacture in half the steps of a conventional stamped steel wheel, and eliminates extensive machining required with forged or cast aluminum wheels.