Search Results

High-voltage battery system plays a critical role in eco-friendly vehicles due to its effect on the cost and the electric driving range of eco-friendly vehicles. In order to secure the customer pool and the competitiveness of eco-vehicle technology, vehicle electrification requires lowering the battery cost and satisfying the customer needs when driving the vehicles in the real roads, for example, maximizing powers for fun drive, increasing battery capacities for achieving appropriate trip distances, etc. Because these vehicle specifications have a critical effect on the high-voltage battery specification, the key technology of the vehicle electrification is the appropriate decision on the specification of the high-voltage battery system, such as battery capacity and power. These factors affect the size of battery system and vehicle under floor design and also the profitability of the eco-friendly vehicles.

A combined experimental and computational study of 3-D unsteady compressible flow in exhaust manifold and CCC system was performed to understand the flow characteristics and to improve the flow distribution of pulsating exhaust gases within monolith. An experimental study was carried out to measure the velocity distribution in production exhaust manifold and CCC under engine operating conditions using LDV (Laser Doppler Velocimetry) system. Velocity characteristics were measured at planes 25 mm away from the front surface of first monolith and between two monolithic bricks. To provide boundary conditions for the computational study, velocity fields according to crank angle were also measured at the entrance of exhaust manifold. The comparisons of exhaust gas flow patterns in the junction and mixing pipe between experimental and computational results were made.

As the current and future emission regulations become stringent, the research on exhaust manifold with CCC (Close Coupled Catalyst) has been the interesting and remarkable subject. To design of exhaust manifold with CCC is a difficult task due to the complexity of the flow distribution caused by the pulsating flows that are emitted at the exhaust ports. This study is concerned with the theoretical and experimental approach to improve catalyst flow uniformity through the basic understanding of exhaust flow characteristics. Computational and experimental approach to the flow for exhaust manifold of conventional cast type, stainless steel bending type with 900 cell CCC system in a 4-cylinder gasoline engine was performed to investigate the flow distribution of exhaust gases.

Diesel engines are the most commonly used power train of the freight and public transportations in the world. From the viewpoint of global warming restraint, however, reduction of exhaust emissions from the diesel engine is urgent demand. Stringent emission regulations are being proposed with growing concern on NOx, PM and CO2 emissions. Future emission regulations require advanced emission control technologies, such as SCR(Selective Catalytic Reduction), LNT(Lean NOx Trap) and EGR(Exhaust Gas Recirculation). The EGR is a commonly used technique to reduce emission. In this study, a LP-EGR(Low Pressure Exhaust Gas Recirculation) system was investigated to evaluate its potential on emission reduction and fuel economy improvement, especially for a passenger diesel engine. A 3.0ℓ diesel engine equipped with the LP-EGR system was tested using an in-house control algorithm.

One of the ways to improve the fuel efficiency of the HEV (Hybrid and Electric Vehicles) is to optimize automotive electric system. In order to achieve this, the LDC (Low voltage DC-DC Converter) variable voltage was controlled. Using the ADAS (Advanced Driver Assistance System) map, the charge-discharge behaviors of 12V lead-acid battery was predicted during driving so that, the battery could be charged efficiently. In this study, the feedback control system for 12V battery discharging was designed to compromise between the 12V battery SOC (State of Charge) and the driving conditions at different traffic points. In contrast to earlier approaches, this experimental result indicates that the LDC variable voltage control based on ADAS is able to reduce the LDC average output power by 17.1% therefore, increasing fuel efficiency and ensuring the durability of the 12V battery.

As environmental problems such as global warming are emerging, regulations on automobile exhaust gas are strengthened and various exhaust gas reduction technologies are being developed in various countries in order to satisfy exhaust emission regulations. Exhaust gas recirculation (EGR) technology is a very effective way to reduce nitrogen oxides (NOx) at high combustion temperatures by using EGR coolers to lower the combustion temperature. This EGR cooler has been mass-produced in stainless steel, but it is expensive and heavy. Recently, high efficiency and compactness are required for the EGR cooler to meet the new emission regulation. If aluminum material is applied to the EGR cooler, heat transfer efficiency and light weight can be improved due to high heat transfer coefficient of aluminum compared to conventional stainless steel, but durability is insufficient. Therefore, the aluminum EGR cooler has been developed to enhance performance and durability.

In this study, a co-operative regenerative braking control algorithm was developed for an electric vehicle (EV) equipped with an electronic wedge brake (EWB) for its front wheels and an electronic mechanical brake (EMB) for its rear wheels. The co-operative regenerative braking control algorithm was designed considering the road friction characteristic to increase the recuperation energy while avoiding wheel lock. A powertrain model of an EV composed of a motor, and batteries and a MATLAB model of the control algorithm were also developed. They were linked to the CarSim model of the vehicle under study to develop an EV simulator. The EMB and EWB were modeled with an actuator, screw, and wedge to develop an EMB and EWB simulator. A co-simulator for an EV equipped with an EWB for the front wheels and an EMB for the rear wheels was fabricated, composed of the EV and the EMB and EWB simulator.

A battery pack case of an electric vehicle was developed with a fibrous thermoplastic composite material. Due to cost effectiveness, long-fiber-reinforced thermoplastics by direct process (D-LFT) were adopted. PA6 (Polyamide 6)-based composites were processed using a D-LFT pilot machine at the temperature range between 250° and 290°. Glass and carbon fibers were added in the matrix varying the mixture ratio of the fibers while keeping the weight fraction 40%. The increase of carbon fibers in the mixture increased tensile modulus and strength, however, decreased Izod impacts strength. The fatigue life of developed composites was evaluated by fatigue tests in tension, which were over one million cycles at the maximum fatigue loading less than 60% of the composite strength. Associated with fiber orientation, anisotropic mechanical behavior was investigated in terms of flexural properties and mold shrinkage.

High specific power, additional hardware and mapping optimization was done to achieve reduction of fuel economy for current engine in this study. 2 stage turbocharger with serial configuration was best candidate not only for high specific power at high engine speed but also for increase of low end torque for current engine. This increase of low end torque is important for development of transient characteristic of vehicle. DoE and efficient EGR Cooler was applied for optimization of fuel economy. DoE was useful for optimization of fuel consumption affected by various fuel injection parameters. This DoE was also efficient for matching optimal fuel economy after change of engine hardware. Performance improvement of engine with 2 stage turbocharger VGT was evaluated and additional development of fuel economy was performed in this study.

We developed new single coated Pd/Rh three-way catalysts (TWC). Several Pd/Rh single layered catalysts were prepared by changing the precious metal (PM) fixation method and adding new base metal oxides (BMO). These samples were compared with double-coated catalyst by using model gas activity test, BET test, XRD test and vehicle emission test. It is found that the performance of the single coated catalyst is as good as that of commercialized double-coated catalyst. The oxygen storage capacity of the single coated catalyst is better than that of double-coated catalyst. Moreover, manufacturing the single coated catalyst enables us to eliminate the unnecessary coating process which is essential to the conventional one. Our test results demonstrate that the developed catalyst has sufficient activity and durability of OSC to meet emission and OBD-II regulations.

As the markets require a more environmentally friendly and high fuel consumption vehicle, we have to satisfy bilateral target. Though many new after-treatment techniques like LNT, SCR are investigated to meet both strong emission regulations and low fuel consumption, high cost of these techniques should be solved to adopt widely. This paper describes how to optimize the dual loop EGR as a tool to reduce CO₂ emission of a HSDI diesel engine in the passenger car application. Focus is not only on the optimization to obtain the maximum CO₂ reduction but also on how to assess and overcome various side effects. As a result of careful optimization, as much as 6% CO₂ reduction was achieved by introduction of low pressure EGR loop, maintaining the same boundary conditions as those with high pressure EGR loop only.

Hyundai Motor Company developed its second-generation fuel cell hybrid electric vehicle (FCEV) based on its small Tucson SUV. Compared to Hyundai's first generation fuel cell vehicle, the Santa Fe FCEV, the Tucson FCEV has an extended driving range plus cold weather starting capability. It incorporates numerous technical advances including a fuel cell that operates at sub-zero temperatures and a new high voltage lithium ion polymer battery. Using both a fuel cell and a high voltage battery as sources for driving energy, the Tucson hybrid system provides optimum driving conditions, which ensures high tank to wheel efficiency. The Tucson FCEV's power plant has been located in the front - under the front hood - unlike its predecessor Santa Fe FCEV, which featured an under-floor installation. More importantly, Tucson FCEV's driving range has been extended to 300km thanks to its 152-liter hydrogen storage tanks.

Lithium-ion battery has advantages of high energy density and cost effectiveness than other types of batteries. However due to the low mechanical stability, their performance is strongly influenced by environmental conditions. Especially, external pressure on a cell surface is a crucial factor because an appropriate force can improve battery cycle life, but excessive force may cause structural failure. In addition, battery pack is composed of various components so that uncertainties in dimension and material properties of each component can cause a wide variance in initial pressure. Therefore, it is important to optimize structural design of battery pack to ensure initial pressure in an effective range. In this paper, target stiffness of module structure was determined based on cell level cycle life test, then structural design has been optimized for weight reduction. Cell cycling tests were performed under different stiffness conditions and analyzed with regression model.

A study of unsteady compressible flow for two types of exhaust manifold and CCC (Close-Coupled Catalyst) systems attached to a 4-cylinder DOHC gasoline engine was carried out to investigate the flow distribution of exhaust gases and finally to make the conversion efficiency of catalyst better. An experimental study was conducted, using LDV technique, to measure the velocity distributions inside exhaust manifolds and CCC under practical engine conditions. In this study, through experiment and calculation, the effects of geometric configuration of exhaust manifold on flow maldistribution in monolith were mainly investigated to understand the exhaust flow structure in terms of flow uniformity and to improve the conversion efficiency. As a result of this fundamental study, the modified exhaust manifold (Type B) was designed and manufactured. Full load performance tests and vehicle emission tests were performed to see the effects of flow characteristics on engine performance and emission.

The electric power system of a modern vehicle has to supply enough electrical energy to numerous electrical and electronic systems. The electric power system of a vehicle consists of two major components: a generator and a battery. A detailed understanding of the characteristics of the electric power system, electrical load demands, and the driving environment such as road, season, and vehicle weight are required when the capacities of the generator and the battery are to be determined for a vehicle. In order to avoid the over/under design problem of the electric power system, an easy-to-use and inexpensive simulation program may be needed. In this study, a vehicle electric power simulator is developed. The simulator can be utilized to determine the optimized capacities of generators and batteries appropriately. To improve the flexibility and easy usage of the simulation program, the program is organized in modular structures, and is run on a PC.

Improved Lean NOx Trap (LNT) catalysts with enhanced NH3 generation feature were developed for the small diesel engine. The next generation LNT system needs to perform good NOx conversions over the wide temperature range including below 200°C for urban driving and above 400°C for motorway of real road driving. However, the extended use of BaO, a component of LNT known to be very effective for high temperature NOx storage, results in the decrease of low temperature NOx conversion due to the degradation of NO oxidation associating with sulfur over time. The improvement of the low-temperature LNT performance is a key requirement for the real driving emission control as the best operation temperature for urea-SCR is above ~250°C. In this study, our next generation LNT with new washcoat architecture has demonstrated improved NOx removal efficiencies under the wider operation temperature window than the current production technology.

The fuel economy of a vehicle can be improved by recuperating the kinetic energy when the vehicle is decelerated. However, if there is no electrical traction component, the recuperated energy can be used only by the other electrical systems of the vehicle. Thus, the fuel economy improvement can be maximized by balancing the recuperated energy and the consumed energy. Also, suitable alternator and battery management is required to maximize the fuel economy. This paper describes a design optimization process of the alternator and battery system equipped with recuperation control algorithms for a mid-sized sedan based on the fuel economy and system cost. A vehicle model using AVL Cruise is developed for cycle simulations and validated with experimental data. The validated model is used for the parametric study and design optimization of the alternator and battery systems with single and dual energy storage.

Recently, the design of automotive headlamps has become diversified and complicated according to customer needs. Hence, structural complexity of the headlamps has also increased. Complex structure of the headlamps inevitably causes a disturbance in air circulation. For this reason, inadvertent micro-sized water droplets, called fogging, are condensed on the inner surface of headlamp lens due to temperature difference between the inner and outer lens surfaces. To circumvent fogging inside of the headlamp lens, an anti-fogging coating is indispensable. Conventionally, diverse surfactants have been adopted as substantial material for the anti-fogging coating. However, the usage of the surfactants causes undesirable side effect such as water mark arising from vapor condensation, which is an important issue that must be fully resolved. In this study, we developed an innovative anti-fogging coating material without using conventional surfactant.

The integration of SCR catalyst into diesel-particulate filter (SDPF) may be one of most viable ways to meet upcoming stringent emission regulations with new test protocols such as Worldwide harmonized Light vehicles Test Cycles (WLTC) and Real Driving Emissions (RDE) requirements. The chabazite-structured SSZ-13-based catalysts enabled the wide implementation of urea-SCR technology for mobile applications due to their robust thermal stability up to 750°C compared to the thermally unstable ZSM-5-based technologies. However, the thermally stable Cu-SSZ-13 catalyst starts losing its initial activity with the increase of aging time at 850°C, where the SCR catalyst on SDPF can possibly be exposed during filter regeneration under a drop-to-idle (DTI) condition. Therefore, more durable SCR catalysts that survive under higher temperatures have been strongly desired in automotive industry. Recently, we found Cu-exchanged high silica LTA revealed an excellent hydrothermal stability.

The performance and marketability of eco-friendly vehicles highly depend on their high-voltage battery system. Lithium-ion pouch cells have advantages of high energy density and cost-effectiveness than other types of batteries. However, due to their low mechanical stability, their characteristics are strongly influenced by external conditions. Especially, external pressure on pouch cell is a crucial factor for the performance, life cycle, and structural safety of battery pack. Therefore, optimizing pressure level has been a critical consideration in designing battery pack structures for lithium-ion pouch cell. In this work, we developed an optimized structure of the battery module and pack to apply appropriate pressure on pouch cells. They also include a standardization strategy to meet the varied demand in capacity and power for automotive application.