Search Results

Consumers design different PHEVs than expert analysts assume. Experts almost uniformly assume PHEVs that offer true all-electric driving for 10 to 60 miles; consumers are more likely to design PHEVs that do not offer true all-electric driving and have short ranges over which they use grid-electricity. Thus consumers? PHEV designs are less expensive. These consumer PHEV designs do, or don?t, produce lower GHG emissions than experts? PHEVs over the next ten years. The devil is in the details, i.e., which powerplant emissions to assign to new electricity demand: marginal or average. If (based on marginal powerplant emissions) it makes almost no difference whether we sell consumer-designed or expert-assumed PHEVs over the next ten years, yet as the grid continues to de-carbonize all-electric PHEV designs emerge as clearly the better option, there is a trajectory we could be on from blended, ?short range? PHEVs to all-electric ?long range? PHEVs.

In the analysis for durability or R&H performance with the full vehicle multibody models, the need for component flexibility is increasing along with demand for more precise full vehicle system. The component elastic deformations are usually expressed by modal superposition from component normal mode analysis with finite element model for reducing model size and simulation time. Although the simulation results of MBD analysis are more accurate according to increasing the number of flexible body and modes, the increasing of flexible components makes worse simulation time and convergence in MBD analysis. Especially, in the MBD analysis including a flexible upper body, in substitution for large number degree of freedom FE model such as trimmed body, it should take a few times longer than the case of rigid upper body This paper proposes the methods of reducing computational cost with adequate mode selections without the loss of simulation accuracy in the flexible MBD.

Fillet and plug weld are commonly used in structural applications in commercial heavy vehicles. This paper is primarily concerned with an investigation of the full field deformations fields in fillet and plug welds using three dimensional digital image correlation (3D-DIC). Two identical vehicle parts are constructed using a fillet weld for one specimen, and a plug weld for the other. The specimens are loaded under quasi-static conditions with simultaneous measurement of load, displacements and strain gage measurements. Strain gage locations are selected based on the results of a finite element analysis model. 3D-DIC measurements are constructed using a two camera setup. Thus, 3D-DIC measurements are compared to strain gage measurements and finite element predictions. The effectiveness of the non-contact full field method is evaluated for application to studying the weld details considered and potential for fatigue damage and durability.

The assessment of the Transmission Loss (TL) of vehicle components at Low-Mid Frequencies generally raises difficulties associated to the physical mechanisms of the noise transmission through the automotive panel. As far as testing is concerned, it is common in the automotive industry to perform double room TL measurements of component baffled cut-outs, while numerical methods are rather applied when prototype or hardware variants are not available. Indeed, in the context of recent efforts for reduction of vehicle prototypes, the use of simulation is constantly challenged to deliver reliable means of decision during virtual design phase. While the Transfer matrix method is commonly and conveniently used at Mid-High frequencies for the calculation of a trimmed panel, the simulation of energy transfer at low frequencies must take into account modal interactions between the vehicle component and the acoustic environment.

For (benchmark) tests it is not only useful to study the acoustic performance of the whole vehicle, but also to assess separate components such as the engine. Reflections inside the engine bay bias the acoustic radiation estimated with sound pressure based solutions. Consequently, most current methods require dismounting the engine from the car and installing it in an anechoic room to measure the sound emitted. However, this process is laborious and hard to perform. In this paper, two particle velocity based methods are proposed to characterize the sound radiated from an engine while it is still installed in the car. Particle velocity sensors are much less affected by reflections than sound pressure microphones when the measurements are performed near a radiating surface due to the particle velocity's vector nature, intrinsic dependency upon surface displacement and directivity of the sensor. Therefore, the engine does not have to be disassembled, which saves time and money.

It is known that SEA is a rapid and simple methodology for analyzing complex vibroacoustic systems. However, the SEA principle is not always valid and one has to be careful about the physical conditions at which the SEA principle is acceptable. In this study, the appropriate damping loss factor of the vehicle interior cavity is studied in the viewpoint of the modal overlap factor of the cavity and the decay per mean free path (DMFP) of the cavity. Virtual SEA tests are performed with an FE model combination, which is suggested by a previous study of Stelzer et al. for the simulation of the sound transmission loss (STL) of vehicle panel structure. The FE model combination is consisting of the body in white (BIW), an acoustical-excited hemisphere-shaped exterior cavity, and the interior cavity. It is found that the DMFP of the interior cavity is appropriate between 0.5 ~ 1 dB for applying SEA principle.

CO2 emission is more serious in recent years and automobile manufacturers are interested in developing technologies to reduce CO2 emissions. Among various environmental-technologies, the use of solar roof as an electric energy source has been studied extensively. For example, in order to reduce the cabin ambient temperature, automotive manufacturers offer the option of mounting a solar cell on the roof of the vehicle [1]. In this paper, we introduce the semi-transparent solar cell mounted on a curved roof glass and we propose a solar energy management system to efficiently integrate the electricity generated from the solar roof into internal combustion engine (ICE) vehicles. In order to achieve a high efficiency solar system in different driving, we improve the usable power other than peak power of solar roof. Peak power or rated power is measured power (W) in standard test condition (@ 25°C, light intensity of 1000W/m2(=1Sun)).

In this article, a new method for achieving piano black appearance is discussed. Using a technique called Direct Coating, developed by Covestro, components have been produced with a smooth, high-gloss surface, which demonstrates improved scratch resistance and the ability to recover from minor scratches. For this development project, the Hyundai Santa Fe exterior door trim was selected due to the simple geometry and severe performance requirements. This allowed for optimization of molding conditions and comparison of the performance to the current production part. The prototype part demonstrated improved surface quality compared to paint, and passed car wash, chemical, and weathering test specifications. In addition to addressing quality issues, this method offers cost savings by eliminating the traditional painting process, which is expensive due to long cycle time, multi-step processing, and emissions regulations.

Impact resistance of plastic underbody parts was studied using simulated injection-molded specimen which can be tested according to different types of material used, injection molding variants like position and number of injection molding gates, and features of ribs. Material applied was glass fiber reinforced polyamide which can be used in underbody parts. Test was performed using several combinations of injection molding gates and rib types. From the test result, optimal design guide for plastic underbody parts was determined. Also, new high impact resistant plastic material made of glass fiber reinforced polyamide 66 (PA66) and polyamide 6 (PA6) alloy was developed and the material properties useful for CAE were determined. As a case study, oil pan and muffler housing were designed following the optimal design guide and CAE. And the reliability of the sample muffler housing designed was verified.

Connected and Autonomous Vehicles (CAV) rely on information obtained from sensors and communication to make decisions. In a Cooperative Vehicle Safety (CVS) system, information from remote vehicles (RV) is available at the host vehicle (HV) through the wireless network. Safety applications such as crash warning algorithms use this information to estimate the RV and HV states. However, this information is uncertain and sparse due to communication losses, limitations of communication protocols in high congestion scenarios, and perception errors caused by sensor limitations. In this paper we present a novel approach to improve the robustness of the CVS systems, by proposing an architecture that divide application and information/perception subsystems and a novel prediction method based on non-parametric Bayesian inference to mitigate the detrimental effect of data loss on the performance of safety applications.

This paper focuses on the optimization of the cross-section of a panel type impact door beam. The key parameters of the cross-section of the beam were artificially changed by using a geometry morphing tool FCM (Fast Concept Modeler), which is plugged in to CATIA. Then, the metamodel of FE (Finite Element) analysis results was created and optimized using LS-OPT. The ANOVA (Analysis of Variance) analysis of results was carried out to find the factor of weight reduction. Finally, a new cross section concept was proposed to overcome the limitation of old structure. The optimization was carried out for the beam with the final cross-section to have 10 % or more reduction in total weight.

The optimal control of anode H2 concentration in fuel cell is the key performance parameter for efficiency and durability of the fuel cell electric vehicle. Implementation of H2 concentration sensor in fuel processing system is the best option to achieve the optimal control operation, but the vulnerability of the chip in H2 concentration sensor to the moisture has not been overcome and no H2 concentration sensor for vehicle application is present in the world so far. Due to the immaturity of the H2 concentration sensor, a number of researches have been being made to keep the H2 concentration in the anode at certain level without H2 concentration sensors. However the effectiveness of those technologies has not been good to meet the design specification in all the operating range of the various driving cycles and environmental condition.

This paper discusses a technology for reducing the gas flow noise generated from the noise of the vehicle, especially the exhaust system. The primary function of the heat protector is thermal shutdown. However, due to the increase in engine power, downsizing of engines, and the rise of consumer's eye level, solutions about noise are now emphasized. To meet these needs, a new concept of heat protector manufacturing technology is required. A key component of this technology is the manufacturing technology of three-ply composite board which can absorb sound from the existing sound insulation aluminum heat protector. For this purpose, mold technology for punching aluminum sheet, optimization technique for punching effect, specific pattern design for high-strength/high-forming, sound absorbing material selection and composite sheet molding technology, and noise vibration reduction mounting technology for plate joining were developed.

Commercially available Third Generation Advanced High Strength Steels (GEN3 AHSS) are qualified by automakers worldwide. With an excellent combination of strength and ductility, GEN3 AHSS are cold-formable and have shown potential to replace press hardenable steels (PHS) in structural applications. With overall formability equivalent to 590DP, U. S. Steel 980 GEN3 AHSS (980 XG3™ AHSS) may achieve cold-formed component geometries similar to those achieved by hot-formed PHS. Furthermore 980 GEN3 AHSS demonstrates a substantial increase in post-forming yield strength due to the combined effects of work-hardening and bake-hardening-thereby contributing strongly toward crash energy management performance. The technical challenges and attributes of cold-formed 980 GEN3 AHSS are explored in this paper for an automotive rear rail application (currently PHS), including: formability analysis, wrinkling elimination and springback compensation.

A supervisory Model Predictive Control (MPC) approach is developed for an air path system for multi-mode operation in a diesel engine. MPC is a control method based on a predictive dynamic model of system and determines actuator control positions through the optimization of various factors such as tracking performances of target setpoints, moving speed of actuators, limits, etc. Previously, linear MPC has been successfully applied on the air path control problem of a diesel engine, however, most of these applications were developed for a single operation mode which has only one set of control target setpoint values. In reality, a single operation mode cannot cover all requirements of current diesel engines and this complicates practical implementations of linear MPC. The high priority targets for the development of diesel engines are low emissions, high thermal efficiency and robustness.

Fuel sloshing noise is involved with flow motion inside fuel tanks as well as structural characteristics of vehicles. Therefore it is necessary to introduce Fluid-Structure Interaction (FSI) analysis to predict sloshing noise phenomena more accurately. Purposes of this paper are to verify the reliability of the FSI method and suggest new CAE analysis processes to predict fuel sloshing noise. The vibration of floor panels induced by sloshing impact is evaluated through FSI analysis. A series of tests is carried out to validate simulation results. The numerical optimization of parameters is also carried out to reduce computation time. In addition, effects of sloshing noise factors are discussed based on simulation and test results. Lastly, a method to predict fuel sloshing noise by exerting sloshing load on a vehicle is suggested.

The Design For Six Sigma (DFSS) process consists of four phases, identification & definition of opportunity, concept development, design optimization, and design verification. In the phase of concept development, TRIZ (Russian acronym for Theory of Inventive Problem Solving) is useful for creating new ideas from the present ideas, which includes the trimming strategy, the antidote strategy, and the picket fence strategy. In this paper, systems of a vehicle such as Variable Compression Ratio (VCR) engine, windshield wiper blade, and Continuously Variable Valve Actuation (CVVA) of engine, are selected and new concepts for each system are created by applying the previously mentioned three strategies. FMEA (Failure Mode and Effects Analysis), the latter part in the phase of concept development in DFSS, is conducted for newly generated concepts of systems that are mentioned above. As a result of FMEA, it is found that the wind lift of the wiper blade can be a serious problem.

In this study, the preliminary validation method of the steering system is constructed and the objective is to satisfy the target performance in the conceptual design stage for minimizing the problems after the detailed design. The first consideration about steering system is how to extract the reliable steering effort for parking. The tire model commonly used in MBD(Multi-Body Dynamics) has limited ability to represent deformations under heavy loads. Therefore, it is necessary to study adequate tire model to simulate the behavior due to the large deformation and friction between the ground and the tire. The two approaches related with F tire model and mathematical model are used. The second is how to extract each link’s load in the conceptual design stage. Until now, each link’s load could be derived only by actual vehicle test, and a durability analysis was performed using only pre-settled RIG test conditions.

The software must be verified and optimized from time to time to ensure system performance quality from the development process. Because the later you discover performance issues, the greater the cost of performance improvements, along with the extent to which they are fixed in the source code. In particular, performance problems due to poor system design should be identified and corrected as soon as possible. Also, as development progresses, source code added for new features and modified by bugs can potentially increase system resource usage or worsen responsiveness. Therefore, the development process needs to periodically measure, analyze, and improve system performance. This paper introduces the system-wide performance analyzer and explains how to use it to measure and analyze the performance of the infotainment system for performance management and improvement.

A sliding door is one of the car door systems, which is generally applied to the vans. Compared with swing doors, a sliding door gives comfort to the passengers when they get in or out the car. With an increasing number of the family-scale activities, there followed a huge demand on the vans, which caused growing interests in the convenience technology of the sliding door system. A typical sliding door system has negative effects on the vehicle interior package and the operating effort. Since the door should move backward without touching the car body, the trajectory of the center rail should be a curve. The curve-shaped center rail infiltrates not only the passenger shoulder room, but also the opening flange curve, which results in the interior package loss. Moreover, as the passenger pulls the door outside handle along the normal direction of the door outer skin, the curved rail causes the opening effort loss.