Search Results

For controlling oxides of nitrogen (NOx) and particular matter (PM) emissions from diesel engines, various fuel and combustion mode modification strategies are investigated in the past. Low temperature combustion (LTC) is an alternative combustion strategy that reduces NOx and PM emissions through premixed lean combustion. Dual fuel reactivity-controlled compression ignition (RCCI) is a promising LTC strategy with better control over the start and end of combustion because of reactivity and equivalence ratio stratification. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions are significantly higher in RCCI, especially at part-load conditions. The present work intends to address this shortcoming by utilizing oxygenated alternative fuels. Considering the limited availability and higher cost, replacing conventional fuels completely with alternative fuels is not feasible.

The presence of unsaturated methyl esters in biodiesel makes it susceptible to oxidation and fuel quality degradation upon long-term storage. In the present work, the effects of oxidation of Karanja biodiesel upon long-term storage on the combustion and emission characteristics of a heavy-duty truck diesel engine are studied. The Karanja biodiesel is stored for one year in a 200 litres steel barrel at room conditions to mimic commercial storage conditions. The results obtained show that compared to diesel, the start of injection of fresh and aged biodiesels are advanced by ~2-degree crank angle, and the ignition delay time is reduced. Aged biodiesel showed a slightly smaller ignition delay compares to fresh biodiesel. The fuel injection and combustion characteristics of fresh and aged biodiesels were similar at all the load conditions. Both fresh and aged biodiesels produced higher oxides of nitrogen (NOx) and lower smoke emissions compared to diesel.

Today, GDI engines are becoming very popular because of better fuel economy and low exhaust emissions. The gain in fuel economy in these engines is realized only in the stratified mode of operation. In wall-guided GDI engines, the mixture stratification is realized by properly shaping the combustion chamber. However, the level of mixture stratification varies significantly with engine operating conditions. In this study, an attempt has been made to understand the effect of engine operating parameters viz., compression ratio, engine speed and inlet air pressure on the level of mixture stratification in a four-stroke wall-guided GDI engine using CFD analysis. Three compression ratios of 10.5, 11.5 and 12.5, three engine speeds of 2000, 3000 and 4000 rev/min., and three inlet air pressures of 1, 1.2 and 1.4 bar are considered for the analysis. The CONVERGE software is used to perform the CFD analysis. Simulation is done for one full cycle of the engine.

In this work a novel mixture injection system has been developed and tested on a two stroke scooter engine. This system admits finely atomized gasoline directly into the combustion chamber. It employs many components that were individually developed, fabricated, tested and then coupled together. A small compressor driven by the engine sends pressurized air at the correct crank angle through a timing valve. This is connected to a mechanical injector through a high pressure pipe. Fuel is metered into the high pressure pipe using a standard low pressure injector. The developed mixture injection system resulted in considerable improvements in thermal efficiency and reduction in HC emissions over the manifold injection method at all engine outputs. A considerable reduction in short circuiting losses was seen. The highest brake thermal efficiency achieved was 25.5% as against 23% with the manifold injection system.

Mixture distribution in the combustion chamber of gasoline direct injection (GDI) engines significantly affects combustion, performance and emission characteristics. The mixture distribution in the engine cylinder, in turn, depends on many parameters viz., fuel injector hole diameter and orientation, fuel injection pressure, the start of fuel injection, in-cylinder fluid dynamics etc. In these engines, the mixture distribution is broadly classified as homogeneous and stratified. However, with currently available engine parameters, it is difficult to objectively classify the type of mixture distribution. In this study, an attempt is made to objectively classify the mixture distribution in GDI engines using a parameter called the “stratification index”. The analysis is carried out on a four-stroke wall-guided GDI engine using computational fluid dynamics (CFD).

Engine modelling aims at studying the combustion related phenomenon occurring in Internal Combustion (IC) engines. In this regard, a low dimensional mathematical model using first principles has been developed to study Spark Ignited (SI) engines. The resulting equations are Ordinary Differential Equations (ODE) (for volume, pressure, torque, speed and work done) and Partial Differential Equations (PDEs) for temperature and species conservation equations (fuel, CO, CO2, NO). This model utilizes simplified reaction kinetics for the oxidation of fuel in the combustion chamber. A two-step mechanism for the combustion of fuel and the classical Zeldovich Mechanism are used to predict the amount of NO formed during combustion. The model is solved in FORTRAN using LSODE subroutine (for stiff equations) with lumped parameters for thermal properties and diffusion, and invoking the ideal gas assumption.

Nowadays, Direct Injection Spark Ignition (DISI) engines are very popular because of their lower fuel consumption and exhaust emissions due to lean stratified mixture operation at most of load conditions. In these engines, achieving mixture stratification plays an important role on performance and emission characteristics of the engine. Also, mixture stratification is mainly dependent on in-cylinder flows and air-fuel interaction, which in turn largely dependent on valve configurations. Therefore, understanding them is very much essential in order to improve the engine performance. In this study, a CFD analysis has been carried out on two- and four-valve four-stroke engines to analyze in-cylinder flows and air-fuel interaction at different conditions. The engines specifications considered here are taken from the literature for which experimental data is available. ‘STAR-CD’ software has been used for the CFD analysis. For meshing, polyhedral trimmed cells have been adopted.

Direct injection diesel engines are used in both light duty and heavy duty vehicles because of higher thermal efficiency compared to SI engines. However, due to only short time available for fuel-air mixing, combustion process depends on proper mixing. As a result, DI Diesel engine emits more NOx and soot into the atmosphere. Therefore, to achieve better combustion with less emission and also to accelerate the fuel-air mixing to improve the combustion, appropriate design of combustion chamber is crucial. Hence, in this work a study has been carried out using CFD to evaluate the effect of combustion chamber configuration on Diesel combustion with two different piston bowls. The two different piston configurations considered in this study are centre bowl on flat piston and pentroof offset bowl piston.

Unsaturated methyl esters in biodiesel make it susceptible to oxidation and fuel quality degradation upon long-term storage. It is almost impossible to use biodiesel for commercial applications immediately after production. The lead time between biodiesel production and usage is generally high, causing auto-oxidation and fuel quality degradation. Hence any onsite improvement in fuel quality should be tested with aged biodiesel. To avoid the food versus fuel debate, non-edible oil feedstocks are preferable for producing biodiesel. However, biodiesel from non-edible oil sources has more unsaturated methyl ester constituents. The traditional trade-off between oxides of nitrogen (NOx) and soot emissions in conventional diesel combustion is reduced to a more severe NOx problem with biodiesel. In the present study, NOx mitigation through fuel modifications is studied for oxidized biodiesel produced from a non-edible oil, Karanja.

Currently, alternative fuels produced from waste resources are gaining much attention to replace depleting fossil fuels. The disposal of waste plastic poses severe environmental problems across the globe. The energy embodied in waste plastics can be converted into liquid fuel by pyrolysis. The present work explores the possibility of utilizing waste plastic oil (WPO) produced from municipal plastic wastes and waste cooking oil (WCO) biodiesel produced from used cooking oil in a dual fuel reactivity-controlled compression ignition (RCCI) mode. A single-cylinder light-duty diesel engine used for agricultural water pumping applications is modified to run in RCCI through suitable intake and fuel injection systems modifications. Alternative fuel blends, viz. WPO and WCO biodiesel with 20 vol. % in gasoline and diesel is used as a port and direct-injected fuels in RCCI. The premixed ratio and direct-injected fuel timings are optimized to achieve maximum thermal efficiency.

Over the years, much progress has been made in automotive vehicle technology to achieve high efficiency and clean combustion. Reactivity controlled compression ignition (RCCI) is one of the most widely studied high-efficiency, clean combustion strategies. However, complex dual-fuel injection systems and associated controls, high unburned hydrocarbon (UHC), and carbon monoxide (CO) emissions limit RCCI use in practical applications. Recently, single fuel RCCI strategies are gaining more attention as the above shortcomings are effectively addressed. Homogeneous charge with direct injection (HCDI) is a single fuel RCCI strategy that results in high thermal efficiency and lower UHC and CO emissions. In HCDI, the port-injected diesel fuel vapour and air are inducted during the intake stroke and ignited with direct-injected diesel fuel near the end of the compression stroke. However, high oxides of nitrogen (NOx) make HCDI less viable for practical applications.

Gasoline direct injection (GDI) engines are well known for their ability to operate at the stratified fuel-air mixture, and thereby they are highly efficient than port fuel injection (PFI) engines. However, the stratification of the in-cylinder mixture leads to higher nitrogen oxides (NOx) and soot emissions with lower hydrocarbon (HC) emissions. The PFI works under a homogeneous mixture, which leads to lower NOx and soot emissions with compensation of HC emissions. By combining the advantages of GDI and PFI modes, it is possible to achieve higher fuel efficiency with lower emissions. Therefore, in the present study, four different injection strategies, namely, pure GDI, gasoline-direct multiple-injection (GDMI), combined GDI with PFI (GDI-PFI), and pure PFI are investigated under various load conditions using computational fluid dynamics (CFD) analysis. The effect of these strategies on mixture formation, indicated mean effective pressure (IMEP), and emissions are evaluated.

The present work investigates the effects of lowering the compression ratio (LCR) from 18:1 to 14:1 and optimizing the fuel injection parameters across the operating range of a mass production light-duty diesel engine. The results were quantified for a regulatory Indian drive cycle using a one-dimensional simulation tool. The results show that the LCR approach can simultaneously reduce the oxides of nitrogen (NOx) and soot emissions by 28% and 64%, respectively. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions increased significantly by 305% and 119%, respectively, with a 4.5% penalty in brake specific fuel consumption (BSFC). Hence, optimization of fuel injection parameters specific to LCR operation was attempted. It was evident that advancing the main injection timing and reducing the injection pressure at low-load operating points can significantly help to reduce BSFC, HC and CO emissions with a slight increase in the NOx emissions.

Gasoline Controlled Auto-Ignition (GCAI) combustion, which can be categorized under Homogeneous Charge Compression Ignition (HCCI), is a low-temperature combustion process with promising benefits such as ultra-low cylinder-out NOx emissions and reduced brake-specific fuel consumption, which are the critical parameters in any modern engine. Since this technology is based on uncontrolled auto-ignition of a premixed charge, it is very sensitive to any change in boundary conditions during engine operation. Adopting real time valve timing and fuel-injection strategies can enable improved control over GCAI combustion. This work discusses the outcome of collaborative experimental research by the partnering institutes in this direction. Experiments were performed in a single cylinder GCAI engine with variable valve timing and Gasoline Direct Injection (GDI) at constant indicated mean effective pressure (IMEP). In the first phase intake and exhaust valve timing sweeps were investigated.

Achieving stable combustion without misfire and knocking is challenging in premixed charge compression ignition (PCCI) especially in small bore, air cooled diesel engines owing to lower power output and inefficient cooling system. In the present study, a single cylinder, air cooled diesel engine used for agricultural water pumping applications is modified to run in PCCI mode by replacing an existing mechanical fuel injection system with a flexible common rail direct injection system. An advanced start of fuel injection (SOI) and exhaust gas recirculation (EGR) are required to achieve PCCI in the test engine. Parametric investigations on SOI, EGR and fuel injection pressure are carried out to identify optimum parameters for achieving maximum brake thermal efficiency. An SOI sweep of 12 to 50 deg. CA bTDC is done and for each SOI, EGR is varied from 0 to 50% to identify maximum efficiency points. It was found that EGR helps in extending the load range from 20 to 40% of rated load.

Gasoline direct injection (GDI) engines are now trending in automobile field because of good fuel economy and low exhaust emissions over their port fuel injection (PFI) counter parts. They operate with a lean stratified mixture in most of conditions. However, their performance is dependent on mixture stratification which in-turn depends on fuel injection pressure, timing and strategy. But, the main challenge to GDI engines is soot and particulate matter (PM) emissions. However, they can be reduced by employing multi-stage fuel injection strategy. Therefore, in the present work, an effort has been made to study the effect of fuel injection parameters on soot emissions of a GDI engine using the CFD analysis. In addition, the study is also extended to evaluate the performance, combustion and other emission characteristics of the engine. First the engine is modelled using the PRO-E software. The geometrical details of the engine are obtained from the literature.

The present research explores the application of biodiesel fuel in a stationary agricultural engine operated under the Homogenous charge compression ignition (HCCI) mode. To achieve HCCI combustion, a fuel vaporizer and a high-pressure port fuel injection system are employed to facilitate rapid evaporation of the biodiesel fuel. The low volatility of biodiesel is one of the significant shortcomings, which makes it inevitable to use a fuel vaporizer at 380oC. Consequently, the charge temperature is high enough to promote advanced auto-ignition. Further, the high reactivity of biodiesel favors early auto-ignition of the charge. Besides, biodiesel exhibits a faster burn rate due to its oxygenated nature. The combined effect of advanced auto-ignition and faster burn rate resulted in a steep rise in the in-cylinder pressures, leading to abnormal combustion above 20% load. Diluting the charge reduces reactivity and intake oxygen concentration, facilitating load extension.