Search Results

As world-wide container volume increases and very large container ships emerge as a dominant player in the maritime cargo transport market, functional capabilities of container ports need to be greatly enhanced. To address this problem, KAIST is undertaking a project to design a novel container transport system, namely Mobile Harbor. Mobile Harbor refers to a system that can go out to a large container ship anchoring in the open sea, load and unload containers between the container ship and the Mobile Harbor, and transport them to their destinations. Designing Mobile Harbor presents a number of challenges as with many other large-scale engineering projects, especially at the beginning stage of the project.

This study mainly focuses on developing an accurate tracking controller for the self-energizing clutch actuator (SECA) system consisting of a DC motor with an encoder applied on the automated manual transmission (AMT). In the position-based actuation of the SECA, abruptly increasing torque near the clutch kissing point during the clutch engagement process induces control input saturation and jerky response when a conventional feedback controller is applied. The proposed work resolves such issue and significantly increases the control accuracy of the actuator through the development of an effective H-infinity controller. The control performance is shown to be more effective than a simple PID controller via simulation and experiments using an AMT test bench equipped with SECA aided by d-SPACE and Matlab/Simulink.

Over the past decade, there have been many efforts to generate engine sound inside the cabin either in reducing way or in enhancing way. To reduce the engine noise, the passive way, such as sound absorption or sound insulation, was widely used but it has a limitation on its reduction performance. In recent days, with the development of signal processing technology, ANC (Active Noise Control) is been used to reduce the engine noise inside the cabin. On the other hand, technologies such as ASD (Active Sound Design) and ESG (Engine Sound Generator) have been used to generate the engine sound inside the vehicle. In the last ISNVH, Hyundai Motor Company newly introduced ESEV (Engine Sound by Engine Vibration) technology. This paper describes the ESEV Plus Minus that uses engine vibration to not only enhance the certain engine order components but reduce the other components at the same time. Consequently, this technology would produce a much more diverse engine sound.

This paper focuses on modeling of the heavy-duty vehicle drivetrain with automatic transmission by using dual clutch scheme. The planetary gear set in the automatic transmission is complicated structure and difficult to understand. The advantage of the dual clutch scheme is that it can be used to represent the complex planetary gear set intuitively, which is a great help to understand the gear shifting process. It is also suitable for being used in the controller due to its low order. Some conditions are required to convert the planetary gear set to the dual clutch model. The heavy-duty vehicle driveline can be converted to the dual clutch model due to its heavy engine and vehicle inertia. This paper also proposes system parameter estimation methods to represent the driveline model. The main parameters are lumped inertia, lumped gear efficiency, output shaft compliance and friction coefficient of clutches.

Demand for electrified vehicles is increasing due to increased environmental pollution regulations and interest in highly efficient vehicles. According to these demands, research on electrified vehicles equipped with Dual Clutch Transmission (DCT) has been actively conducted for the purpose of improving energy efficiency of electrified powertrain, maximizing acceleration performance, and increasing maximum speed. However, since DCT requires clutch to clutch shifting, it is difficult to control drive torque and slip speed using two clutch actuators and a power source input. In order to solve this, a study on a multivariable shift controller has been conducted. However, this study chose a heuristic planning method to control the two outputs. However, since the slip speed and drive torque are coupled, it is necessary to tune the reference for every shift scenario, as well as create unnecessary control inputs or degrade shift control performance.

As customer awareness of product sound grows, the need exists to ensure that product sound quality is maintained in the manufacturing process. To this end in-process controls that employ a variety of traditional acoustical and alternate sound quality metrics are utilized, usually partly or wholly housed in a test enclosure. Often times these test cells are required to attenuate the background noise in the manufacturing facility so that the device under test can be accurately assessed. While design guidelines exist the mere size and cost of such booths make an iterative build and test approach costly in terms of materials as well as engineering and testing time. In order to expedite the design process and minimize the number of confirmation prototypes, SEA can be utilized to predict the transmission loss based upon material selection and booth construction techniques.

In many cases, the results from a sound transmission loss (STL) test can differ from facility to facility. Despite the presence of standardized test specifications such as SAE J1400 [1], many issues can create variations in the data unique to that particular setup. These situations have presented themselves in recent tasks in which a reverberation room was relocated into a smaller area than was previously available. Current test projects in the relocated test facility have shown a need to better understand the details influencing the quality of the test data. Issues such as the sample orientation, the volume of the reverberation room, the quality of the sealing between the reverberation and anechoic rooms and even the material itself or the operator's style of positioning the sample all had to be reconsidered. It was determined that an investigation into causes of these differences needed to be launched to improve the setup of the STL test and provide more reliable data.

Lear Corporation has developed a new OneStep™ Liftgate trim module. The panel consists of all mechanical components and a trim cover assembled into one module. This structural liftgate uses the trim substrate and a “beam” as the common attachment point for all liftgate hardware. The assembly includes all of the liftgate components mounted to the back of the interior trim panel.

Recently, as a automobile becomes more electronic and intelligent, MEMS(Micro Electro Mechanical System) sensors lead the technology and market of automotive sensor by overcome limitation of size, accuracy and reliability of mechanical sensors. Accelerometer, gyro, and pressure sensor are mainly studied MEMS sensor in the automobile field. Specially, intensification of safety regulation has increased the requirement and interest of the accelerometer. There are piezoelectric, piezoresistive, capacitive type in the sensing method of the accelerometer. Among these, piezoelectric method has high sensitivity feature with a simple manufacturing process. In this paper, we fabricated Flexural Plate Wave(FPW) accelerometer which sense frequency change of the vibrating piezoplate and found a optimum condition of the piezoplate shape and manufacturing condition to improve performances by using the design of experiment.

Design of geometric shape for visco-elastic vibration isolation elements is frequently based on experiences, intuitions, or trial and errors. Such practices make it often difficult for drastically different or new concepts to come out. In this paper, both a topological method and a shape optimization method are combined together to find out a most desirable isolator shape efficiently by using two commercial engineering programs, ABAQUS and MATLAB. The procedure is divided into two steps. At first, the topology optimization method is employed to find an initial shape, where material density of each finite element is chosen as either 0 or 1 for physical realization. Based on the initial shape, then, finer tuning is done by the boundary movement method. An illustration of the procedure is presented for a vehicle engine mount and the effectiveness will be discussed.

Two-stage injection strategy was studied in dimethyl-ether homogeneous charge compression ignition engine combustion. An early direct injection, main injection, was applied to form a premixed charge followed by the second injection after the start of heat release. Experiments were carried out in a single-cylinder direct-injection diesel engine equipped with a common-rail injection system, and the combustion performance and exhaust emissions were tested with the various second injection timings and quantities. Engine speed was 1200 rpm, and the load was fixed at 0.2 MPa IMEP. Main injection timing for homogeneous mixture was fixed at −80 CAD, and the fuel quantity was adjusted to the fixed load. Second injection quantity was varied from 1 to 5 mg, and the timing was selected according to the heat release rate of the HCCI combustion without second injection.

In recent years, the perceived quality of powered seat adjusters based on their sound during operation has become a primary concern for vehicle and seat manufacturers. Historical noise targets based on overall dB(A) at the occupant's ear have consistently proved inadequate as a measure of the sound quality of a seat adjuster. Significant effort has been devoted to develop alternative sound quality metrics that can truly discriminate between “good” and “bad” seat adjusters. These new metrics have been successfully applied for some years by product development engineers in test labs. However, in the assembly plant the sound quality of the seat adjuster is still assessed subjectively by an operator at the end of the assembly line. The main problem with this approach is not only the lack of consistency and repeatability across large samples of seat tracks, but also the fact that the only feedback provided from the end-of-line to the product development team is of subjective nature.

Concepts for dual density materials for usage as absorbers and decouplers are based on well-established layered media principles and have been applied for many years in non-automotive applications. Balancing the mass, air flow resistance, and thickness allows for improved noise attenuation in the low to mid frequency range which is of particular interest for automotive NVH management. Using these principles, products were tuned via mass and airflow resistance to reduce noise levels while also significantly reducing mass. Validation in various vehicles confirmed that up to a 55% reduction of a sound package's mass is possible. The considerable weight reductions of dash insulators and carpet systems are possible at the same times as the sound level in the vehicle interior is at least maintained and frequently improved.

Automobile manufacturers recently requested the help of the SAE Acoustical Materials Committee to develop standard data formats that could be used by suppliers to present data on NVH products. An SAE task force with representatives from material suppliers and from OEMs chose formats covering a broad range of acoustical tests commonly conducted in the automotive industry. These formats cover both material and vehicle tests. They include details on samples and test conditions and graphs with preferred axes and data ranges. SAE recommended practice J2629 will be issued that describes the use of these preferred formats for acoustical data. The automobile manufacturers have requested that all suppliers of NVH products use these formats to present results from this point onward.

For the assessment of vehicle acoustics in the early design stages of a vehicle program, the use of full vehicle SEA models is becoming the standard analysis method in the US automotive industry. One benefit is that OEM's and Tier 1 suppliers are able to cascade lower level acoustic performance targets for NVH systems and components. Detailed SEA system level models can be used to assess the performance of systems such as dash panels, floors and doors, however, the results will be questionable until test data Is available. Correlation can be accomplished with buck testing, which is a common practice in the automotive industry for assessing the STL (sound transmission loss) of vehicle level components. The opportunity to conduct buck testing can be limited by the availability of representative bodies to be cut into bucks and the availability of a transmission loss suite with a suitably large opening.

Interior noise has become a significant performance attribute in modern passenger vehicles and this is extremely important in the luxury market segment where a quiet interior is the price of entry. With the elimination of early prototype vehicles to reduce development costs, high frequency analytical SEA models are used to design the vehicle sound package to meet targets for interior noise quality. This function is important before representative NVH prototypes are available, and later to support parameter variation investigations that would be cost prohibitive in a hardware test. This paper presents the application of an analytical full vehicle SEA model for the development of the acoustic package of a cross over luxury utility vehicle. The development concerns addressed were airborne powertrain noise and road noise. Power flow analysis was used to identify the major noise paths to the interior of the vehicle.

Unweighted dB, dB(A), and Articulation Index do not always accurately identify the sound quality of vehicle interior noise. This paper attempts to determine the relevance of sound quality in interior automotive acoustics. Traditionally, overall dB(A) levels have been the driving factor, along with cost, in selecting an interior automotive acoustic package. In this paper, we make use of subjective jury evaluations to compare perceptions of various interior acoustic packages and compare these results to objective values. These values include, but are not restricted to, dB, dB(A), and Articulation Index. Considerations are made as to whether differences between packages can be perceived by customers. This paper also attempts to show that subjective evaluations can differ with the standard metrics used to select acoustic packages and describe why such evaluations might be important in acoustic package selection.

Turbocharger is one of the main parts for high power and low fuel consumption. But due to high RPM of turbocharger causes noise problem. Flow in the turbocharger is very fast and unsteady so it's very hard to estimate the noise and to reduce. So, we conducted experiment in anechoic room using airflow bench which uses compressed air as the power source. Through experiment we can identify the noise component radiated from turbocharger. As we know, tonal noise is dominant component which is related to RPM and some other noise components are confirmed. To analyze noise source and mechanism in detail, we proceed to numerical analysis. First to see the flow in the turbocharger, computational fluid dynamics(CFD) method is used. Using CFD method, we can see the flow in turbocharger and get base data for acoustic analysis. Surface pressure data resulted from CFD method is used for acoustic analogy analysis and boundary element method(BEM).

The regulation of NOx emission from a diesel engine is becoming stricter by the environmental agency and furthermore, EGR has been adopted to reduce NOx emission. Air flow control of a diesel engine combined with turbocharger and EGR is complicated because turbocharger and EGR are coupled physically. This paper examines the design of a model based control structure for diesel engine with a turbocharger and EGR. Model based control provides desirable control strategies from the physical analysis of an engine model. Air fraction and exhaust manifold pressure target based control simulation was conducted in this research. Engine is highly nonlinear and susceptible to uncertainties. To overcome this problem, a robust controller was designed by using a sliding mode control method.

Upon the need of a highly efficient transmission system for conventional cars and the hybrid electric vehicle (HEV) purposes, in the paper, clutchless geared transmission system (CGST) by removing the clutch and incorporating a planetary gear system connected to a motor is newly proposed. The dynamic analysis of CGST operations is carried out, using the lever analogy of planetary gear. The state space model and the mathematical model of CGST structure are derived. Through the simulations of CGST operations, input-output tests and gear shifts are performed. To verify the simulation result, reduced size of CGST testbench is developed and experimented.