Search Results

The combustion and exhaust emission characteristics of a DME fueled HCCI engine were investigated. Different fuel injection strategies were tested under various injection quantities and timings with exhaust gas recirculation (EGR). The combustion phase in HCCI was changed by an in-cylinder direct injection and EGR, due to changes in the in-cylinder temperature and mixture homogeneity. The gross indicated mean effective pressure (IMEPgross) increased and the hydrocarbon (HC) and carbon monoxide (CO) emissions decreased as the equivalence ratio was augmented. The IMEPgross with direct injection was greater than with the port injection due to retarded ignition timing resulting from latent heat of direct injected DME fuel. It was because that most of burn duration was completed before top dead center owing to higher ignitability for DME with high cetane number. However, HC and CO emissions were similar for both injection locations.

The use of clean gaseous fuel in automotive engines has been continuously increased in order to meet the reinforcing emission regulations and to efficiently utilize limited natural resources. Since the liquid phase LPG injection (LPLI) system has an advantage of higher power and lower emission characteristics than the mixer type fuel supply system, many studies and applications have been conducted. However, the heat extraction, due to the evaporation of liquid LPG fuel, causes not only a dropping of LPG fuel but also icing phenomenon that is a frost of moisture in the air around the nozzle tip. Because both lead to a difficulty in the control of accurate air fuel ratio, it can result in poor engine performance and a large amount of HC emissions. The main objective of this study is to examine the characteristics of icing phenomenon and also aims to improve it through the use of anti-icing injection tip. An experimental investigation was carried out on the bench test rig in this study.

Exhaust gases of diesel vehicles are considered as a major reason of city air pollutions. The DOC(Diesel Oxidation Catalyst) and DPF(Diesel Particulate Filter) have been used to reduce the emissions of diesel vehicles. The DOC can oxides HC, CO and SOF(Soluble Organic Fraction) in the PM emissions, and the DPFs can filter the most of solid PM, such as carbon particles. As the DPFs, wall flow type ceramic honeycomb filters have been commonly used and now being still advanced. However, the cost and durability of the currently used DPFs are not perfect yet. Metal foam is the one of promising materials for the DPFs due to its cost effectiveness, good thermal conductivity and high mechanical strength. The metal foam can be produced with various pore sizes and strut thickness and finally can be coated with catalytic wash-coats with low cost.

The combustion, knock characteristics and exhaust emissions in an engine were investigated under homogeneous charge compression ignition operation fueled with liquefied petroleum gas with regard to variable valve timing and the addition of di-methyl ether. Liquefied petroleum gas was injected at an intake port as the main fuel in a liquid phase using a liquefied injection system, while a small amount of di-methyl ether was also injected directly into the cylinder during the intake stroke as an ignition promoter. Different intake valve timings and fuel injection amount were tested in order to identify their effects on exhaust emissions, combustion and knock characteristics. The optimal intake valve open timing for the maximum indicated mean effective pressure was retarded as the λTOTAL was decreased. The start of combustion was affected by the intake valve open timing and the mixture strength (λTOTAL) due to the volumetric efficiency and latent heat of vaporization.

High-speed video imaging in a swirl-supported (Rs = 1.7), direct-injection heavy-duty diesel engine operated with moderate-to-high EGR rates reveals a distinct correlation between the spatial distribution of luminous soot and mean flow vorticity in the horizontal plane. The temporal behavior of the experimental images, as well as the results of multi-dimensional numerical simulations, show that this soot-vorticity correlation is caused by the presence of a greater amount of soot on the windward side of the jet. The simulations indicate that while flow swirl can influence pre-ignition mixing processes as well as post-combustion soot oxidation processes, interactions between the swirl and the heat release can also influence mixing processes. Without swirl, combustion-generated gas flows influence mixing on both sides of the jet equally. In the presence of swirl, the heat release occurs on the leeward side of the fuel sprays.

Filtration studies about the metal foam filters combined with electrostatic precipitation, which can be used as a new DPF device, have been performed. Filtration efficiency of the metal foam filter is significantly low because most particles are penetrated through the large filter-pores. However the efficiency was considerably improved by forming a high electric field on the filter surface. The pressure drop was not significantly increased by the particle deposition because the particles do not completely clog the filter pores.

Dimethyl ether (DME) as a high cetane number fuel and liquefied petroleum gas (LPG) as a high octane number fuel were supplied together to evaluate the controllability of combustion phase and improvement of power and exhaust emission in homogeneous charge compression ignition (HCCI) engine. Each fuel was injected at the intake port and in the cylinder separately during the same cycle, i.e., DME in the cylinder and LPG at the intake port, or vice versa. Direct injection timing was varied from 200 to 340 crank angle degree (CAD) while port injection timing was fixed at 20 CAD. In general, the experimental results showed that DME direct injection with LPG port injection was the better way to increase the IMEP and reduce emissions. The direct injection timing of high cetane number fuel was important to control the auto-ignition timing because the auto-ignition was occurred at proper area, where the air and high cetane number fuel were well mixed.

This paper describes the results of a DOE (design of experiment) applied to an exhaust heat exchanger to lower the exhaust gas temperature mainly under high load conditions. The heat exchanger was installed between the exhaust manifold and the inlet of the close-coupled catalytic converter (CCC) to avoid thermal aging. The DOE evaluates the influence of the selected eight design parameters of the heat exchanger geometry on the performance of the exhaust gas cooling system, and the interaction between these parameters. To maximize the heat transfer between exhaust gas and coolant, fins were implemented at the inner surface of the heat exchanger. The design parameters consist of the fin geometry (length, thickness, arrangement, number of fin), coolant direction, exchanger wall thickness, and the length of the heat exchanger. The acceptable range of each design parameter is discussed by analyzing the DOE results.

Exhaust gas recirculation (EGR) and lean burn utilize the diluents into the engine cylinder to control combustion leading to enhanced fuel economy and reduced emissions. However, the occurrence of excessive cyclic variation with high diluent rates, brings about an undesirable combustion instability within the engine cylinder resulting in the deterioration of both engine performance and emissions. Proper stratification of mixture and diluents could improve the combustion stability under high diluent environment. EGR stratification within the cylinder was made by adopting a fast-response solenoid valve in the midst of EGR line and controlling its timing and duty. With EGR in both homogeneous mode and stratified mode, in-cylinder pressure and emissions were measured. The thermodynamic heat release analysis showed that the burning duration was decreased in case of stratified EGR. It was found that the stratification of EGR hardly affected the emissions.

A LPG engine for heavy duty vehicle has been developed using liquid phase LPG injection (hereafter LPLI) system, which has a strong potential as a next generation LPG fuel supply system. It has been revealed in this work that an LPLI system generates higher power, efficiency, and emits lower emission pollutants than the conventional mixer type system. As a preliminary study on the LPLI system applicable to a heavy duty LPG engine, the engine output and combustion performance were investigated with various operating conditions using a single cylinder engine equipped with the different fuel supply systems. Experimental results showed that no problems occurred and the volumetric efficiency and engine output increased, respectively by about 10%, when the LPLI system is used. A decrease of the intake manifold temperature by the LPLI system has also been observed.

In order to reduce hydrocarbon emission in gasoline engine, especially during warming-up period, it is necessary to estimate the fuel and fuel product flow rate in the emission gas. The intake airflow rate should also be estimated. A strategy was proposed to estimate air fuel ratio in a spark ignition engine. The mass of air in the cylinder was determined by filling-emptying method, and the fuel in the intake manifold and cylinder was estimated by the “wall-wetting” effect calculation. The use of graphical dynamic system control software is becoming more popular as automotive engineers strive to reduce the time to develop new control systems. The rapid prototype engine controller has been developed by using MATLAB, SIMULINK, REAL TIME WORKSHOP, xPC Target, and WATCOM C++. The sensor data from the engine will be transferred to computer, and the fuel delivery will be calculated.

To meet stringent emission standards, a considerable amount of development work is necessary to ensure suitable efficiency and durability of catalyst systems. The main challenge is to reduce the engine cold-start emissions. Close-coupled catalyst (CCC) provides fast light-off time by utilizing the energy in the exhaust gas. However, if some malfunction occurred during engine operation and the catalyst temperature exceeds 1050°C, the catalytic converter becomes deactivated and shows poor conversion efficiency. Close-coupled catalyst temperature was investigated under various engine operating conditions. All of the experiments were conducted with a 1.0L SI engine at 1500-4000 rpm. The engine was operated at no load to full load conditions. Exhaust gas temperature and catalyst temperature were measured as a function of lambda value (0.8-1.2), ignition timing (BTDC 30°-ATDC 30°) and misfire rates (0-28%).

Combustion and flame propagation characteristics of the liquid phase LPG injection (LPLI) engine were investigated in a single cylinder optical engine. Lean burn operation is needed to reduce thermal stress of exhaust manifold and engine knock in a heavy duty LPG engine. An LPLI system has advantages on lean operation. Optimized engine design parameters such as swirl, injection timing and piston geometry can improve lean burn performance with LPLI system. In this study, the effects of piston geometry along with injection timing and swirl ratio on flame propagation characteristics were investigated. A series of bottom-view flame images were taken from direct visualization using a UV intensified high-speed CCD camera. Concepts of flame area speed, in addition to flame propagation patterns and thermodynamic heat release analysis, was introduced to analyze the flame propagation characteristics.

An 11L heavy duty LPG MPI engine has been developed using the liquid phase LPG injection system, which is one of the next generation LPG fueling technologies, since the LPG MPI engine can achieve the higher power and efficiency, and lower exhaust emissions than the conventional mixer type system. Two prototypes - a natural aspiration(NA) engine and a turbocharged inter-cooler(TCI) engine - were developed in this work and tested to measure the performance and emissions. For a NA type engine, in order to achieve the low emissions, the stoichiometric air/fuel ratio was adapted with a three-way catalytic converter. Whereas, for a TCI type, the lean burn technology was introduced to minimize the thermal loading due to an increase of the engine power. The results in this work demonstrated that the LPG MPI engines have the higher engine performance and lower exhaust emissions than the base diesel engine.

Dimethyl Ether (DME) has been considered as one of the most attractive alternative fuels for compression ignition engine. Its main advantage in compression-ignition engine application is high efficiency of diesel cycle with soot free combustion though conventional fuel injection system has to be modified due to the intrinsic properties of the DME. Experimental study of the DME and conventional diesel spray employing a common-rail type fuel injection system with a sac type injector was performed in a constant volume vessel pressurized by nitrogen gas. A CCD camera was employed to capture time series of spray images, so that spray cone angles and penetrations of the DME spray were characterized and compared with those of diesel. Intermittent hesitating DME spray appeared at injection pressures of 25MPa and 40MPa in both atmospheric and 3MPa chamber pressures.

An LPG engine for heavy duty vehicles has been developed using liquid phase LPG injection (hereafter LPLI) system, which has regarded as as one of next generation LPG fuel supply systems. In this work the optimized piston cavities were investigated and chosen for an LPLI engine system. While the mass production of piston cavities is considered, three piston cavities were tested: Dog-dish type, bathtub type and top-land-cut bathtub type. From the experiments the bathtub type showed the extension of lean limit while achieving the stable combustion, compared to the dog-dish type at the same injection timing. Throughout CFD analysis, it was revealed that the extension of lean limit was due to an increase of turbulence intensity by the enlarged crevice area, and the enlargement of flame front surface owing to the shape of the bathtub piston cavity compared to that of the dog-dish type.

A liquid phase LPG injection (LPLi) system has been considered as one of the next generation fuel supply system, since it has a very strong potential to accomplish the higher power, higher efficiency, and lower emission characteristics than the mixer type that is classified as a second generation technology, whereas the LPLi system is classified as a third generation technology. However, when a liquid LPG fuel is injected into the inlet duct of an engine, a large quantity of heat is extracted due to its high latent heat of evaporation. This leads the moisture in the air to freeze around the nozzle exit, which is called icing phenomenon. It may cause damage to the outlet nozzle of an injector or inlet valve seat. In this work, the experimental investigation of the icing phenomenon was carried out. The results showed that humidity of air rather than the temperature of air in the inlet duct mainly controlled the icing process.

To investigate the mixture distributions in an LPG engine with Liquid phase port injection for heavy duty vehicles, an optical single cylinder engine, which is optically accessible both in side and bottom view, and laser diagnostic system were incorporated to apply PLIF (planar laser induced fluorescence) technique. Acetone was used as a dopant in LPG fuel, which was excited by KrF excimer laser (248nm), and its fluorescence images were acquired with ICCD camera. The effects of fuel injection timing, swirl intensity and excess air ratio were investigated. For the case of open valve injection, favorable stratification of fuel, both in axial and radial direction, was clearly observed compared to the closed valve injection, where reverse stratification in axial direction was observed. At the Ricardo swirl ratio of 3.4, it was apparent that excessive axial stratification of fuel got dominant, which would lead to poor engine performances.

Submodels are developed for injection, evaporation and wall impingement of a liquid LPG spray. The injection model determines the quality of fuel as two-phase choke flow at the nozzle exit. Wind tunnel experiments show the spray penetration more sensitive to ambient flow velocity than to injection pressure. Most evaporation occurs during choking, while heat transfer from surrounding air has a negligible effect on downstream droplet sizes. Three dimensional simulation shows that the bathtub cavity is better than the dog-dish cavity for stable flame propagation in lean-burn conditions. The injection timing during the IVC period has a negligible effect, while injection during an intake stroke enhances fuel/air mixing to result in more homogeneous cylinder charge.

Most passenger vehicles employ manual or automatic transmission in their power train. Recently, some automated geared transmission including the dual clutch transmission is gaining popularity for its fuel efficiency and smooth driving as well as convenience. In this study, we are proposing a new much simplified clutchless geared transmission which may transmit most powerful torque employing the power-merge planetary gear system to the final drive during gear shift with excellent smoothness in the transmitted torque. This transmission might work for the most kinds of vehicles having internal combustion engine including the hybrid vehicles.