Search Results

In this work, constant volume combustion is studied using a zero-dimensional FORTRAN code, which is a wide-ranging chemical kinetic simulation that allows a closed system of gases to be described on the basis of a set of initial conditions. The model provides an engine- or reactor-like environment in which the engine simulations allow for a variable system volume and heat transfer both to and from the system. The combustion chamber is divided into two zones as burned and unburned ones, which are separated by an assumed thin flame front in the combustion model used for this work. Equilibrium assumptions have been adopted for the modeling of the thermal ionization, where Saha's equation was derived for singly ionized molecules. The investigation is focused on the thermal ionization of NO as well as for other species. The outputs generated by the model are temperature profiles, species concentration profiles, ionization degree and an electron density for each zone.

A naturally aspirated in-line six-cylinder 2.9-litre Volvo engine is operated in Homogeneous Charge Compression Ignition (HCCI) mode, using camshafts with low lift and short duration generating negative valve overlap. This implementation requires only minor modifications of the standard SI engine and allows SI operation outside the operating range of HCCI. Standard port fuel injection is used and pistons and cylinder head are unchanged from the automotive application. A heat exchanger is utilized to heat or cool the intake air, not as a means of combustion control but in order to simulate realistic variations in ambient temperature. The combustion is monitored in real time using cylinder pressure sensors. HCCI through negative valve overlap is recognized as one of the possible implementation strategies of HCCI closest to production. However, for a practical application the intake temperature will vary both geographically and from time to time.

The main benefit of HCCI engines compared to SI engines is improved fuel economy. The drawback is the diluted combustion with a substantially smaller operating range if not some kind of supercharging is used. The reasons for the higher brake efficiency in HCCI engines can be summarized in lower pumping losses and higher thermodynamic efficiency, due to higher compression ratio and higher ratio of specific heats if air is used as dilution. In the low load operating range, where HCCI today is mainly used, other parameters as friction losses, and cooling losses have a large impact on the achieved brake efficiency. To initiate the auto ignition of the in-cylinder charge a certain temperature and pressure have to be reached for a specific fuel. In an engine with high in-cylinder cooling losses the initial charge temperature before compression has to be higher than on an engine with less heat transfer.

Frontal collisions account for the majority of car accidents. Regulations have been in effect since the late sixties, aiming at assuring a basic safety performance for cars in this type of crash. From a legislative point of view tests as e.g. FMVSS 208 are about to be complemented by other frontal impact configurations. Two of the reasons behind this is to allow assessment also of asymmetric loads to the vehicle front and the level of passenger compartment intrusion. This paper offers a comparison of different frontal crash tests, including Volvo's Severe Partial Overlap Collision (SPOC) and offset tests against a deformable barrier. The methods are evaluated with respect to their results, both from a dummy performance point of view and based on car deformation characteristics. Also, the practicability and possible effect on vehicle designs are discussed.

OBD II established a new level for automotive on board diagnostics. This concept, state of the art, is already introduced on the market, MY-94, ( reference 1). We will now go one step further by introducing the Diagnose 2 Concept. With D2 we connect almost all ECU's in a vehicle to the same diagnostic communication bus, connected to the same pin, (pin 7 in the J1962 connector). It will now be possible to hook up to all ECU's with one connector, the OBD II connector inside the passenger compartment, (this will not be any problem for a properly programmed OBD II Scan Tool, as it only will look for the emission related ECU's).

A rear seat belt system with a submarining-preventing seat design was developed. The seat has a contoured floor pan with a pronounced ridge at the front end and a seat belt with carefully located attachment points. Sled tests simulating 30 mph barrier crashes were run with both a standard Part 572 dummy and a Part 572 dummy with a modified pelvis. Both dummies had pelvis mounted submarining indicators. Comparative tests were run with a rear seat with a flat floor pan. The tests proved the efficacy of the ridge type seat in preventing submarining as well as giving low injury criteria. The modified pelvis was found to have submarining characteristics slightly different from the Part 572 pelvis. Under certain conditions the submarining indicators were capable of detecting when the lap belt loads the abdomen, but failed in some cases where the pelvis rotation was excessive.

This paper describes some of the engineering situations encountered during the development of a three point belt for the rear center seating position in a sedan car. The belt will be sold as an accessory for the after market. The reinforcement of the parcel shelf to achieve a sufficiently strong anchorage for the retractor and the geometrical locations of the belt anchorages are presented. The conflict between the geometrical requirements, the design and the visibility will be focussed. The need for updated requirements for belt installations in the rear center seating position will be pointed out. Data from the performed tests show that all demands from regulations and “in-house” requirements are fulfilled.

A theoretical investigation is presented concerning how the heat transfer process from the gas in the combustion chamber, burned as well as the unburned gas regions, to the walls is affected by the autoignition phenomenon in SI engines. The zonal model in ref. [1] is adapted for the calculations. The radiative heat flux during the heat release period and the heat transfer in the thermal boundary layer by convection are predicted for situations when autoignition has occurred. The cylinder wall temperature is also used as a parameter in this study. The effects of engine operating parameters such as engine speed, timing of ignition, duration time of flame propagation and the fuel parameter Research Octane Number, i.e., RON, on the heat flux to the walls have been studied. The heat release is calculated for a detailed chemical kinetic model, refs. [1, 2 and 3].

An experimental and theoretical study of the effect of thermal barriers and catalytic coatings in a Homogeneous Charge Compression Ignition (HCCI) engine has been conducted. The main intent of the study was to investigate if a thermal barrier or catalytic coating of the wall would support the oxidation of the near-wall unburned hydrocarbons. In addition, the effect of these coatings on thermal efficiency due to changed heat transfer characteristics was investigated. The experimental setup was based on a partially coated combustion chamber. The upper part of the cylinder liner, the piston top including the top land, the valves and the cylinder head were all coated. As a thermal barrier, a coating based on plasma-sprayed Al2O3 was used. The catalytic coating was based on plasma-sprayed ZrO2 doped with Platinum. The two coatings tested were of varying thickness' of 0.15, 0.25 and 0.6 mm. The compression ratio was set to 16.75:1.

Heat transfer losses are one of the largest loss contributions in a modern internal combustion engine. The aim of this study is to evaluate the contribution of the piston bowl type and swirl ratio to heat losses and performance. A commercial CFD tool is used to carry out simulations of four different piston bowl geometries, at three engine loads with two different swirl ratios at each load point. One of the geometries is used as a reference point, where CFD results are validated with engine test data. All other bowl geometries are scaled to the same compression ratio and make use of the same fuel injection, with a variation in the spray target between cases. The results show that the baseline case, which is of a conventional diesel bowl shape, provides the best emission performance, while a more open, tapered, lip-less combustion bowl is the most thermodynamically efficient.

It is generally accepted that knocking combustion influences the heat transfer in SI engines. However, the effects of heat transfer on the onset of knock is still not clear due to lack of experimental data of the thermal boundary layer close to the combustion chamber wall. This paper presents measurements of the temperature in the thermal boundary layer under knocking and non-knocking conditions. The temperature was measured using dual-broadband rotational Coherent anti-Stokes Raman Spectroscopy (CARS). Simultaneous time-resolved measurements of the cylinder pressure, at three different locations, and the heat flux to the wall were carried out. Optical access to the region near the combustion chamber wall was achieved by using a horseshoe-shaped combustion chamber with windows installed in the rectangular part of the chamber. This arrangement made CARS temperature measurements close to the wall possible and results are presented in the range 0.1-5 mm from the wall.