Search Results

Vehicles produced in decades past were fitted with very few antennas. In most cases only an AM or FM antenna was required. In contrast to this, today's vehicles are fitted with a plethora of antennas to receive a wide variety of signals at a number of different frequencies. This work presents a wideband radiating structure capable of sending and receiving many of the signals required in a modern vehicle from a single device. The antenna is based on Planar Inverted Cone Antenna geometry. The effect of bending or curving the antenna substrate is investigated at values in the range that may be required for vehicular integration.

When presented with new technology that removes past constraints, it is often beneficial to revisit old learning's to see if they still hold, and to understand how these can be best applied to the new technology. Brake-By-Wire (BBW) systems replace all the mechanical linkages of conventional hydraulic brake systems with ‘dry’ electrical components [2],[3]. The advent of this technology poses the possibility of revisiting conventional ABS control systems by utilizing the continuous nature that BBW offers. Presented is a BBW model based wheel slip controller using a generic continuous time Model Predictive Control (MPC) algorithm [15]. The result being the first of many steps taken in understanding the full potential that BBW systems offer.

The paper presents experimental analysis of the airflow around the differential center housing of a rear drive full-scale passenger car. The study included investigation of local airflow total and static pressure, as well as surface flow visualization. Estimation of the local airflow velocity is based on the measured pressure coefficients. The experiments were carried out at different test facilities: in a climatic wind tunnel, in a full-scale wind tunnel and on-road. Influence of side wind was modeled by the yawing of the car in the full-scale wind tunnel. The results show the asymmetrical structure of the flow in both, vertical and horizontal planes. Estimated longitudinal relative local velocity decreases from maximum Vr ≈ 0.4 at the lower surface of the center housing, to about Vr ≈ 0 above the upper surface. Side wind increases airflow velocity around the center housing within the investigated yaw range ± 20°

The focus of internal combustion (IC) engine research is the improvement of fuel economy and the reduction of the tailpipe emissions of CO2 and other regulated pollutants. Promising solutions to this challenge include the use of both direct-injection (DI) and alternative fuels such as liquefied petroleum gas (LPG). This study uses Mie-scattering and schlieren imaging to resolve the liquid and vapor phases of propane and iso-octane, which serve as surrogates for LPG and gasoline respectively. These fuels are imaged in a constant volume chamber at conditions that are relevant to both naturally aspirated and boosted, gasoline direct injection (GDI) engines. It is observed that propane and iso-octane have different spray behaviors across these conditions. Iso-octane is subject to conventional spray breakup and evaporation in nearly all cases, while propane is heavily flash-boiling throughout the GDI operating map.

The paper presents a novel concept of very efficient transportation engines for operation with CNG, LNG or LPG. The combustion system permits mixed diesel/gasoline-like operation changing the load by quantity of fuel injected and modulating the premixed and diffusion combustion phases for high fuel energy transfer to piston work. A waste heat recovery system (WHRS) is then recovering the intercooler and engine coolant energy plus the exhaust energy. The WHRS uses a power turbine on the exhaust and a steam turbine feed by a single loop turbo-steamer. The WHRS is the enabler of much faster warm up of the engine and further improvements of the top fuel conversion efficiency to above 50% for the specific case with reduced fuel efficiency penalties changing the load or the speed.

The paper presents a novel concept of a very efficient transportation engines for operation with CNG, LNG or LPG. The paper considers the options of single fuel design with jet ignition and dual fuel design with Diesel and gas. In the first option gas fuel is injected into the main chamber by a direct injector and ignited by jet ignition. In the second option gas fuel is injected into the main chamber by a direct injector and ignited by the direct injection of a small quantity of Diesel fuel. Injection and ignition may be tuned to control the amount of premixed and diffusion combustion to produce the best fuel conversion efficiency vs. load and speed requirements within the prescribed pressure and temperature constraints.

The paper presents a survey of the opportunities to convert compression ignition heavy duty truck engines to work on single or dual fuel modes with CNG. In one popular option, the compression ignition engine is converted to spark ignition with throttle load control and port injection of the CNG. In another option of increasing popularity, the LNG is directly injected and ignited by direct injection of pilot Diesel. This latter option with direct injection of natural gas and diesel through separate injectors that are fully independent in their operation is determined to be the most promising, as it is expected to deliver better power density and similar part load fuel economy to Diesel.

Kinetic energy recovery systems (KERS) placed on one axle coupled to a traditional thermal engine on the other axle is possibly the best solution presently available to dramatically improve the fuel economy while providing better performances within strict budget constraints. Different KERS may be built purely electric, purely mechanic, or hybrid mechanic/electric differing for round trip efficiency, packaging, weights, costs and requirement of further research and development. The paper presents an experimental analysis of the energy flow to and from the battery of a latest Nissan Leaf covering the Urban Dynamometer Driving Schedule (UDDS). This analysis provides a state-of-the-art benchmark of the propulsion and regenerative braking efficiencies of electric vehicles with off-the-shelve technologies.

High-frequency pressure probes were used to map the airflow around a full-scale truck during on-road testing and around a model-scale truck during wind tunnel testing. Several configurations were tested during each type of testing. Results are presented for on-road ‘pass-by’ tests and detail velocity and coefficient of pressure variation alongside the truck at different heights. The wind tunnel data are results of flow mapping about a 10% scale model and show the velocity and coefficient of pressure distribution under and around the model truck for different configurations.

Compressed natural gas (CNG) is an attractive, alternative fuel for spark-ignited (SI), internal combustion (IC) engines due to its high octane rating, and low energy-specific CO2 emissions compared with gasoline. Directly-injected (DI) CNG in SI engines has the potential to dramatically decrease vehicles’ carbon emissions; however, optimization of DI CNG fueling systems requires a thorough understanding of the behavior of CNG jets in an engine environment. This paper therefore presents an experimental and modeling study of DI gaseous jets, using methane as a surrogate for CNG. Experiments are conducted in a non-reacting, constant volume chamber (CVC) using prototype injector hardware at conditions relevant to modern DI engines. The schlieren imaging technique is employed to investigate how the extent of methane jets is impacted by changing thermodynamic conditions in the fuel rail and chamber.

Accurate and robust tracking of objects is of growing interest amongst the computer vision scientific community. The ability of a multi-sensor system to detect and track objects, and accurately predict their future trajectory is critical in the context of mission- and safety-critical applications. Remotely Piloted Aircraft System (RPAS) are currently not equipped to routinely access all classes of airspace since certified Detect-and-Avoid (DAA) systems are yet to be developed. Such capabilities can be achieved by incorporating both cooperative and non-cooperative DAA functions, as well as providing enhanced communications, navigation and surveillance (CNS) services. DAA is highly dependent on the performance of CNS systems for Detection, Tacking and avoiding (DTA) tasks and maneuvers.

This paper presents the conceptual design of a new low-cost measurement system for the determination of pollutant concentrations associated with aircraft operations. The proposed system employs Light Detection and Ranging (LIDAR) and passive electro-optics equipment installed in two non-collocated components. The source component consists of a tuneable small-size and low-cost/weight LIDAR emitter, which can be installed either on airborne or ground-based autonomous vehicles, or in fixed surface installations. The sensor component includes a target surface calibrated for reflectance and passive electro-optics equipment calibrated for radiance, both installed on an adjustable support. The proposed bistatic system determines the column-averaged molecular and aerosol pollutant concentrations along the LIDAR beam by measuring the cumulative absorption and scattering phenomena along the optical slant range.

A unified approach to cooperative and non-cooperative Detect-and-Avoid (DAA) is a key enabler for Remotely Piloted Aircraft System (RPAS) to safely and routinely access all classes of airspace. In this paper state-of-the-art cooperative and non-cooperative DAA sensor/system technologies for manned aircraft and RPAS are reviewed and the associated multi-sensor data fusion techniques are discussed. A DAA system architecture is presented based on Boolean Decision Logics (BDL) for selecting non-cooperative and cooperative sensors/systems including both passive and active Forward Looking Sensors (FLS), Traffic Collision Avoidance System (TCAS) and Automatic Dependent Surveillance - Broadcast (ADS-B). After elaborating the DAA system processes, the key mathematical models associated with both non-cooperative and cooperative DAA functions are presented.

Multi-Sensor Data Fusion (MSDF) techniques involving satellite and inertial-based sensors are widely adopted to improve the navigation solution of a number of mission- and safety-critical tasks. Such integrated Navigation and Guidance Systems (NGS) currently do not meet the required level of performance in all flight phases of small Remotely Piloted Aircraft Systems (RPAS). In this paper an innovative Square Root-Unscented Kalman Filter (SR-UKF) based NGS is presented and compared with a conventional UKF governed design. The presented system architectures adopt state-of-the-art information fusion approach based on a number of low-cost sensors including; Global Navigation Satellite Systems (GNSS), Micro-Electro-Mechanical System (MEMS) based Inertial Measurement Unit (IMU) and Vision Based Navigation (VBN) sensors.

Flow control over aerodynamic shapes in order to achieve performance enhancements has been a lively research area for last two decades. Synthetic Jet Actuators (SJAs) are devices able to interact actively with the flow around their hosting structure by providing ejection and suction of fluid from the enclosed cavity containing a piezo-electric oscillating membrane through dedicated orifices. The research presented in this paper concerns the implementation of zero-net-mass-flux SJAs airflow control system on a NACA0015, low aspect ratio wing section prototype. Two arrays with each 10 custom-made SJAs, installed at 10% and 65% of the chord length, make up the actuation system. The sensing system consists of eleven acoustic pressure transducers distributed in the wing upper surface and on the flap, an accelerometer placed in proximity of the wing c.g. and a six-axis force balance for integral load measurement.

Global Navigation Satellite Systems (GNSS) can support the development of low-cost and high performance navigation and guidance architectures for Unmanned Aircraft Systems (UAS) and, in conjunction with suitable data link technologies, the provision of Automated Dependent Surveillance (ADS) functionalities for cooperative Sense-and-Avoid (SAA). In non-cooperative SAA, the adoption of GNSS can also provide the key positioning and, in some cases, attitude data (using multiple antennas) required for automated collision avoidance. A key limitation of GNSS for both cooperative (ADS) and non-cooperative applications is represented by the achievable levels of integrity. Therefore, an Avionics Based Integrity Augmentation (ABIA) solution is proposed to support the development of an Integrity-Augmented SAA (IAS) architecture suitable for both cooperative and non-cooperative scenarios.

Avionic system developers are currently working on innovative technologies that are required in view of the rapid expansion of global air transport and growing concerns for environmental sustainability of aviation sector. Novel Communication, Navigation and Surveillance (CNS) system designs are being developed in the CNS/Air Traffic Management (CNS/ATM) and Avionics (CNS+A) context for mission-and safety-critical applications. The introduction of dedicated software modules in Next Generation Flight Management Systems (NG-FMS), which are the primary providers of automated navigation and guidance services in manned aircraft and Remotely-Piloted Aircraft Systems (RPAS), has the potential to enable the significant advances brought in by time and trajectory based operations. High-integrity, high-reliability and all-weather services are required in the context of four dimensional Trajectory Based Operations / Intent Based Operations (TBO/IBO).

Hydrogen Internal Combustion Engine (ICE) vehicles using a traditional ICE that has been modified to use hydrogen fuel are an important mid-term technology on the path to the hydrogen economy. Hydrogen-powered ICEs that can run on pure hydrogen or a blend of hydrogen and compressed natural gas (CNG) are a way of addressing the widespread lack of hydrogen fuelling infrastructure in the near term. Hydrogen-powered ICEs have operating advantages as all weather conditions performances, no warm-up, no cold-start issues and being more fuel efficient than conventional spark-ignition engines. The Wankel engine is one of the best ICE to be converted to run hydrogen. The paper presents some details of an initial investigation of the CAD and CAE modeling of a novel design where two jet ignition devices per rotor are replacing the traditional two spark plugs for a faster and more complete combustion.

With the purpose of reducing emission level while maintaining the high torque character of diesel engine, various solutions have been proposed by researchers over the world. One of the most attractive methods is to use dual fuel technique with premixed gaseous fuel ignited by a relatively small amount of diesel. In this study, Methane (CH4), which is the main component of natural gas, was premixed with intake air and used as the main fuel, and diesel fuel was used as ignition source to initiate the combustion. By varying the proportion of diesel and CH4, the combustion and emissions characteristics of the dual fuel (diesel/CH4) combustion system were investigated. Different cases of CFD studies with various concentration of CH4 were carried out. A validated 3D quarter chamber model of a single cylinder engine (diesel fuel only) generated by using AVL Fire ESE was modified into dual fuel mode in this study.

The air entrainment process of a compressed natural gas transient fuel jet was investigated in a constant-volume chamber using Schlieren and particle image velocimetry (PIV) techniques. A new method of calculating air entrainment around a gaseous fuel jet is proposed using Schlieren and PIV imaging techniques. This method offers an alternative to calculation of an alternative to calculation of entrainment using LIF technique in gaseous fuel jets. Several Jet-ambient pressure ratios were tested. In each test, nitrogen was used to fill the chamber as an air surrogate before the jet of natural gas was injected. Schlieren high speed videography and PIV experiments were performed at the same conditions. Schlieren mask images were used to accurately identify the jet boundary which was then superimposed onto a PIV image. Vectors adjacent to the Schlieren mask in the PIV image were used to calculate the spatial distribution of the air entrainment at the jet boundary.