Search Results

Environmental consciousness and tightening emissions legislation push the market share of electronic fuel injection within a dynamically growing world wide small engines market. Similar to automotive engines during late 1980's, this opens up opportunities for original equipment manufacturers (OEM) and suppliers to jointly advance small engines performance in terms of fuel economy, emissions, and drivability. In this context, advanced combustion system analyses from automotive engine testing have been applied to a typical production motorcycle small engine. The 125cc 4-stroke, 2-valve, air-cooled, single-cylinder engine with closed-loop lambda-controlled electronic port fuel injection was investigated in original series configuration on an engine dynamometer. The test cycle fuel consumption simulation provides reasonable best case fuel economy estimates based on stationary map fuel consumption measurements.

Since the introduction of the 4-speed automatic transmissions W4A040 in 1979 and W4A020 in 1981, more than 50% of Mercedes-Benz cars have been equipped with automatic transmissions. These transmissions have undergone continuous development since their introduction. Due to engine/transmission management, the kick-down shift points are electronically influenced, the shift comfort is improved partially by ignition timing manipulation. During the warm-up phase the shift points are raised via output signals from the electronic engine system to improve exhaust gas emissions. In this paper considerations are explained which resulted in supplementing the proven four-speed transmission with a five-speed transmission.

The stricter worldwide emission legislation and growing demands for lower fuel consumption and CO2-emission require for significant efforts to improve combustion efficiency while satisfying the emission quality demands. Ethanol fuel combined with boosting on direct injection gasoline engines provides a particularly promising and, at the same time, a challenging approach. Brazil is one of the main Ethanol fuel markets with its E24 and E100 fuel availability, which covers a large volume of the national needs. Additionally, worldwide Ethanol availability is becoming more and more important, e.g., in North America and Europe. Considering the future flex-fuel engine market with growing potentials identified on downsized spark ignition engines, it becomes necessary to investigate the synergies and challenges of Ethanol boosted operation. Main topic of the present work focuses on the operation of Ethanol blends up to E100 at high loads up to 30 bar imep.

A previous study by the authors has shown an efficiency benefit of up to Δηi = 10 % for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine compared to the homogeneous stoichiometric operation with port fuel injection (PFI). While best efficiencies appeared at extremely lean operation at λ = 3.2, minimum HC emissions were found at λ = 2. The increasing HC emissions and narrow ignition time frames in the extremely lean stratified operation have given the need for a detailed analysis. To further investigate the mixture formation and flame propagation und these conditions, an optically accessible single-cylinder engine was used. The mixture formation and the flame luminosity have been investigated in two perpendicular planes inside the combustion chamber.

The principle strategy, the development emphasis, and the investigation parameters of a DI gasoline engine are discussed. Several different combustion systems are briefly described and one system where the spark plug is located near the fuel injector is investigated. In addition, the influence of different operating parameters are studied. Some reasons for the improvement in the efficiency of a DI gasoline engine are shown with the help of thermodynamic analysis and simulation calculations. These show that at a constant operating point (engine speed = 2000 rpm, bmep = 2 bar) there is a reduction of the fuel consumption of 23% at unthrottled conditions in comparison to the homogeneous stoichiometric operation. In particular, the reduction of the pumping and heat losses and the reduction of the exhaust gas energy are responsible for this fuel consumption reduction.

This paper describes an ion current measurement system with a new, modified inductive ignition system and evaluates the detection quality for misfire and knock detection. The System uses an ignition circuit with adjustable spark duration limitation. The measurement circuit is located at the low tension side of the secondary ignition coil. Due to the fact that a lot of influencing factors on misfire detection have been investigated, the estimation of the signal-to-noise-ratio is possible as well as the detection of critical operation points. Results of a closed-loop knock control with ion current are presented and are compared with the structure borne noise method.

1 A recent breakthrough in understanding the origin of ion signals from operating combustion engines [12] led to a new approach in integrating advanced ion current sensing into a compact ignition system. Thus it is now possible to continuously monitor mixture, ignition and combustion properties through online ion current recordings via a novel AC technique. In this paper this AC technique is compared to the standard DC technique and its known drawbacks: expensive high voltage components, sensitivity to plug fouling and expensive electronics. The AC technique is based on the specific properties of the electrical field of spark plugs being characterized by a point source with an extreme inhomogeneity of the electrical field due to the small center electrode. This causes a distinct diode characteristic of the ion signal: very low signals for negative voltages and high signals for positive ion sensing voltages, respectively.

External Exhaust Gas Recirculation (EGR) provides an opportunity to increase the efficiency of turbocharged spark-ignition engines. Of the competing technologies and configurations, Low-Pressure EGR (LP-EGR) is the most challenging in terms of its dynamic behavior. Only some of the stationary feasible potential can be used during dynamic engine operation. To guarantee fuel consumption-optimized engine operation with no instabilities, a load point-dependent limitation of the EGR rate or alternatively an adaptation of the operating point to the actual EGR rate is crucial. For this purpose, a precise knowledge of efficiency and combustion variance is necessary. Since the operating state includes the actual EGR rate, it has an additional dimension, which usually results in an immense measuring effort.

The introduction of stricter emission legislation and the demand of increased power for small two-wheelers lead to an increase of technical requirements. Especially the introduction of liquid-cooling over air-cooling allows the introduction of higher compression ratios, which improves power output as well as thermodynamic efficiencies and thereby fuel consumption. But an increase in compression ratio also introduces further challenges during transient behavior especially close to idling. In order to keep the two-wheeler specific responsiveness of the vehicle, the overall rotational inertia of the engine must be kept low. But the combination of low inertia and high compression ratio can lead to a stalling of the engine if the throttle is opened and closed very quickly in idle operation. The fast opening and closing of the throttle is called a throttle blip.

In the discussion on the reduction or complete avoidance of CO2-emissions and other pollutants in the transport sector, hydrogen as a carbon-free fuel, is an alternative to conventional fuels. The use of hydrogen in modern internal combustion engines offers a fast and cost-effective opportunity of decarbonisation of the transport sector. The utilisation of hydrogen as fuel in internal combustion engine systems is more challenging than using conventional fuels. Hydrogen is highly flammable, which affects the requirements of the ignition system and the design of the combustion chamber. In addition, due to the gaseous state of H2 the question, how the fuel should be delivered to the combustion chamber is of high importance by means of engine performance. There are two fundamentally different concepts for hydrogen injection. Hydrogen can be injected by a multi-point injection into intake manifold by external mixture-formation (MPI) or directly into the combustion chamber (DI).