Search Results

Previous research has shown that elevating fuel injection pressure results in better air-fuel mixture formation, allowing for a further increase in maximum exhaust gas recirculation (EGR) rate while consequently reducing NOx emissions. The aim of this paper is to find out whether there is an optimum injection pressure for lowest soot-NOx emissions at a given boost pressure in high-speed diesel engines. Experiments are carried out on a single-cylinder research engine with a prototype common-rail system, capable of more than 200 MPa injection pressure. The effect of injection pressure on soot-NOx formation is investigated for a variety of boost conditions, representing the conditions of single to multi-stage turbocharger systems. Analysis of the data is performed at the application relevant soot to NOx ratio of approximately 1:10. It is observed that above a critical injection pressure, soot-NOx emissions are not reduced any further.

In this article a new zero-dimensional model is presented for simulating the cylinder pressure in direct injection diesel engines. The model enables the representation of current combustion processes considering multiple injections, high exhaust gas recirculation rates, and turbocharging. In these methods solely cycle-resolved, scalar input variables from the electronic control unit in combination with empirical parameters are required for modeling. The latter are adapted automatically to different engines or modified applications using measured cylinder pressure traces. The verification based on measurements within the entire operating range from engines of different size and type proves the universal applicability and high accuracy of the proposed method.

Using an engine simulation code (WAVE) combined with statistical experimental design and optimisation techniques, the potential of a combined Miller cycle and internal EGR heavy duty engine for future truck applications (Euro 3 and 4) has been assessed. The practical issues related to a suitable variable valve timing or actuation system and boosting strategy have been considered. It is found that, whilst internal EGR levels suitable for future European emissions legislation cycles are possible, the boost pressures needed at high load to maintain a suitable air/fuel ratio when running a valve timing strategy to give acceptable levels of in-cylinder temperature (via the Miller system) are beyond the capabilities of current technology. It is believed, however, that such a system may still be suitable for application in markets which have duty cycles less dependent upon full load operation, for example Japan and, possibly, the USA.

Gaseous emissions were sampled from the exhaust of a single cylinder version of a modern four-valve homogeneous charge spark-ignition engine. The hydrocarbon emissions were extensively analysed using capillary gas chromatography. Levels of key components of the hydrocarbons including methane, benzene and 1, 3-butadiene, were related to fuel composition, mixture strength and exhaust gas recirculation rate. It was shown that the relative levels of hydrocarbon emissions could generally be explained from a knowledge of chemical mechanisms. The significance of the observed trends for the development of engines with reduced levels of hydrocarbon emissions is considered.

Novel Combustion technologies and strategies show high potential in reducing the fuel consumption of gasoline spark ignition (SI) engines. In this paper, a comparison between various gasoline combustion concepts at two representative engine operating points is shown. Advantages of the combustion concepts are analyzed using thermodynamic split of losses method. In this paper, a tool for thermodynamic assessment (Split of Losses) of conventional and new operating strategies of SI engine and its derivatives is used. Technologies, like variable valve actuation and/or gasoline direct injection, allow new strategies to run the SI engine unthrottled with early inlet valve closing (SI-VVA) combined with high EGR, charge stratification (SI-STRAT) and controlled auto ignition (CAI), also known as gasoline homogeneous charge compression ignition (HCCI). These diverse combustion concepts show thermodynamic gains that stem from several, often different sources.

A system for stratifying recycled exhaust gas (EGR) to substantially increase dilution tolerance has been applied to a multi-cylinder port injected four-valve gasoline engine. This system, dubbed Combustion Control through Vortex Stratification (CCVS), has shown greatly improved fuel consumption at stoichiometric conditions whilst retaining ULEV compatible engine-out NOx and HC emission levels. A production feasible variable air motion system has also been assessed which enables stratification at part load with no loss of performance or refinement at full load.

It has been shown by calculation that, for given engine operating conditions, there should be an optimum rate of combustion for minimum Nox emissions from spark ignited engines. This paper gives experimental results from a single cylinder engine which confirm the theory, and show that, for a particular engine, the normal combustion rate needed reducing at zero EGR and increasing at high EGR rates, in opposition to its natural tendency to decrease. The effect on economy was a small loss at zero EGR, but an appreciable improvement at high EGR. Cyclic variation and octane requirement studies are also included.

The usage of Electronic Diesel Control is increasing with todays stringent emissions regulations. This requirement also necessitates that such systems be versatile to meet the needs of the engine/vehicle manufacturer. EGR, start of injection, and fuel delivery can be electronically controlled. Depending on the design goals of the manufacturer any one or two of these can be controlled for partial and all of them for full Electronic Diesel Control. The development and application process has several critical areas. These include, development of the sensors, application of the different subsystems, failure warning and failure mode operation. All of these must be combined if design goals are to be met. As the capabilities of electronics increase it follows that electronic vehicle systems will also improve. Today impressive results have been achieved with systems that are in full or pilot production.

The advantages of closed, loop over open loop control systems are generally recognised. However, existing engine management systems implement most control functions in open loop because suitable feedback sensors are not available. Even for so-called closed loop air fuel ratio controllers, shortcomings of the exhaust gas oxygen (EGO) sensor limit the potential effectiveness of closed loop control. A more direct measure of the combustion process, such as cylinder pressure, can yield sufficient information for the closed loop operation of many of the combustion control functions; this paper presents the results of a prediction algorithm which can derive a variety of feedback signals from cylinder pressure. Cylinder pressure, together with several combustion variables, including air-fuel ratio, exhaust gas recirculation rate, and NOx HC, CO and CO2 emissions were measured at various operating points.

Natural gas is one of the alternative fuels to diesel being considered for low emissions heavy-duty applications. The favoured operating strategies for low emissions SI gas engines are identified as those with high levels of dilution - stoichiometric operation with EGR, and lean-burn. A well-matched exhaust catalyst is needed to produce the lowest emissions levels. Increasing the accuracy of transient air-fuel ratio control is shown to improve the emissions still further. The most favourable combinations of engine operating strategy and control accuracy are identified with respect to fuel economy and first cost. The Co-Nordic Natural Gas Bus Project is an example of an engine development programme aimed at achieving the lowest possible exhaust emissions levels, and as such uses the lowest emissions approach of a stoichiometric engine strategy with EGR and high accuracy control.

It is expected that heavy duty engine legislation in Europe will continue to drive down test cycle BSNox emissions to levels of between 2.5 and 3.5 g/kWh by 2005, with a reduction in particulate emissions to between 0.02 and 0.08 g/kWh. It is unlikely that re-optimisation of existing engine combustion systems alone, such as further retardation of the fuel injection timing, will be sufficient to meet the legislated BSNox targets. Other measures, such as cooled EGR or new aftertreatment systems must therefore be considered. Such emissions control strategies may conflict with other market requirements for improved fuel consumption and increased power density. In this paper, research at Ricardo into the configuration of a premium heavy duty truck engine for the European market for model year 2005 and beyond, is described. A review of the market requirements, projected to 2005 was undertaken in order to define the specification of the concept engine.

The success of model-based ECU-functions relies on precise and efficient modeling of the behavior of combustion engines. Due to the limited computing power, usually a combination of physical models and calibration parameters is preferred for engine modeling in ECU. The parameters can be scalars, 1 or 2-dimensional empirical models, such as look-up table for volumetric efficiency and effective area of the exhaust gas recirculation (EGR). A novel algorithm is proposed to automatically calibrate the look-up tables characterizing stationary functional relationships in ECU-function of the air system of a diesel engine with minimum calibration cost. The algorithm runs in the framework of online design of experiment (DoE), in which Gaussian process model (GPM) is adopted to approximate the relationships of interest.

The spatial distribution of internal exhaust gas recirculation (EGR) is evaluated in an optically accessible direct injection spark ignition engine using near infrared laser absorption to visualize the distribution of the H2O molecule. The obtained overall internal exhaust gas recirculation compares well to gas-exchange cycle calculations and the spatial distributions are consistent with those measured with inverse LIF. The experimental procedures described in this report are designed to be simple and rapidly implemented without the need to resort to unusual optical components. The necessary spectral data of the selected absorption line is obtained from the HITEMP database and is validated with prior experiments carried out in a reference cell. Laser speckle in the images is effectively reduced using a ballistic diffuser.