Search Results

Direct gasoline injection is one major approach in reducing fuel consumption to fulfill the stages of CO2 reduction commitments in Europe from today until 2008. One effort is to unthrottle the gasoline engine during idle and partial load utilizing charge stratification. This may be realized by using different combustion concepts. This paper shows the analysis of mixture preparation for three different types of direct injected gasoline engines. Each engine was driven with two injectors which have two different atomization concepts. The engine types draw a clear dividing line between their combustion concepts. The injectors were analyzed in a pressure chamber, in an optical engine, and in an actual 1-cylinder engine. The formation of wall-film in wall-guided combustion systems will be discussed. Several important injector and engine parameters for fuel direct injection are pointed out.

The fuel spray behavior in the near nozzle region of a gasoline injector is challenging to predict due to existing pressure gradients and turbulences of the internal flow and in-nozzle cavitation. Therefore, statistical parameters for spray characterization through experiments must be considered. The characterization of spray velocity fields in the near-nozzle region is of particular importance as the velocity information is crucial in understanding the hydrodynamic processes which take place further downstream during fuel atomization and mixture formation. This knowledge is needed in order to optimize injector nozzles for future requirements. In this study, the results of three experimental approaches for determination of spray velocity in the near-nozzle region are presented. Two different injector nozzle types were measured through high-speed shadowgraph imaging, Laser Doppler Anemometry (LDA) and X-ray imaging.

A previous study by the authors has shown an efficiency benefit of up to Δηi = 10 % for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine compared to the homogeneous stoichiometric operation with port fuel injection (PFI). While best efficiencies appeared at extremely lean operation at λ = 3.2, minimum HC emissions were found at λ = 2. The increasing HC emissions and narrow ignition time frames in the extremely lean stratified operation have given the need for a detailed analysis. To further investigate the mixture formation and flame propagation und these conditions, an optically accessible single-cylinder engine was used. The mixture formation and the flame luminosity have been investigated in two perpendicular planes inside the combustion chamber.

New energy scenarios for decentralised stationary energy supply based on Liquid Organic Hydrogen Carriers (LOHC) offer an attractive application for hydrogen engines and are a reason why hydrogen engines become topical again. Since hydrogen stored in LOHCs is released under ambient pressure and temperatures of over 200°C, compression and cooling of the hydrogen is needed, lowering the system's overall efficiency. Direct injection of hydrogen is advantageous due to its low volumetric energy density and the tendency towards pre-ignition. The development objective is an injection and combustion strategy for an engine in the performance category below 15 kW and the described fuel supply scenario. Therefore, an one dimensional simulation model of the engine and the hydrogen supplying compressor was built. The simulation results show a large influence of the injection pressure on engine efficiency due to the hydrogen supplying compressor.

Two-dimensional Mie and LIEF techniques were applied to investigate the spray formation of a high pressure gasoline swirl injector in a constant volume chamber. The results obtained provide information on the propagation of liquid fuel and fuel vapor for different fuel pressures and ambient conditions. Spray parameters like tip penetration, cone angles and two new defined parameters describing the radial fuel distribution were used to quantify the fuel distributions measured. Simultaneous detection of liquid and vapor fuel was applied to study the influence of ambient temperature, injector temperature and ambient pressure on the evaporating spray.

The introduction of the so called Emission Controlled Areas within the IMO Tier III legislation forces manufacturers of maritime propulsion systems to adherence to stringent emission thresholds. Dual fuel combustion, which is characterized by the injection of a small amount of fuel oil to ignite a premixed natural gas air mixture, constitutes an option to meet this target. At high diesel substitution rates and very short pilot injection events, the injector is operated in the ballistic regime. This influences spray penetration, mixture formation and ignition behavior. In the present work, a seven-hole dual fuel injector was measured in a combustion chamber to provide data for the generation of a CFD model using the commercial code AVL FIRE®. The liquid and the vapor phase of the fuel spray were quantified by Mie-scattering and Schlieren-imaging technique for different chamber conditions.

In DISI engines spray distribution and atomization directly influence mixture formation, the quality of combustion and the resulting emissions. Constant Volume Chambers (CVC) are commonly used to characterize sprays of gasoline injectors. The CVCs provide good optical access but the flow condition of the engine cannot be reproduced. Optically accessible engines in contrast deliver realistic flow conditions but have restricted optical access. In former investigations we compared the spray propagation of different injectors in constant volume chambers and in optical accessible engines. These results showed a clear difference of the spray propagation in the CVC and the engine, especially at high charge motion conditions in the engine. To find an appropriate way to investigate the impact of different charge motion a flow channel was built with adjustable crossflow velocities from 5-50 m/s. The spray propagation during the injection process was measured with high-speed shadowgraphy.

In a study using a single-cylinder engine a significant potential in fuel efficiency and emission reduction was found for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine. The control of the mixture formation process appeared to be critical to ensure stable inflammation of the mixture. Therefore, optical investigations of the mixture formation were performed on a geometric equivalent, optically accessible single-cylinder engine to investigate the correlation of mixture formation and inflammability. The two optical measurement techniques infrared (IR) absorption and laser-induced fluorescence (LIF) were employed. Mid-wavelength IR absorption appeared to be qualified for a global visualization of natural gas injection; LIF allows to quantify the equivalence ratio inside a detection level. While LIF measurements require complex equipment, the IR setup consists merely of a black body heater and a mid-wavelength sensitive IR camera.