Search Results

This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.

Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.

Optical fiber has begun replacing copper in avionic networks. So far, however, it has been mainly restricted to non-critical applications (video transmission to the flight deck, IFE?). In order to take advantage of the high-bandwidth, low weight, no EMI properties of optical fibers in all data transmission networks, it will be necessary to improve the testing. One part of the puzzle, which is still missing, is the self-test button: the possibility to check the network and detect potential failures before they occur. The typical testing tool of a technician involved in optical fiber cables is the ?light source ? optical power meter? pair. With this tool, one can measure the insertion loss of the fiber link. A second important parameter, the return loss at each optical connector, is not analysed. In addition, this is only a global measurement, which does not allow the detection of possible weak points.

Probabilistic methods are used in calculating composite part design factors for, and are intended to conservatively compensate for worst case impact to composite parts used on space and aerospace vehicles. The current method to investigate impact damage of composite parts is visual based upon observation of an indentation. A more reliable and accurate determinant of impact damage is to measure impact energy. RF impact sensors can be used to gather data to establish an impact damage benchmark for deterministic design criteria that will reduce material applied to composite parts to compensate for uncertainties resulting from observed impact damage. Once the benchmark has been established, RF impact sensors will be applied to composite parts throughout their life-cycle to alert and identify the location of impact damage that exceeds the maximum established benchmark for impact.

Not available.

Not available.

This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations

Standardize plastic fitting hose terminations and drop distances for SAE J2044 fittings

This document will detail the standard method for measuring the reporting the spin loss and efficiency of driveshafts (halfshafts and propeller shafts).

This recommended practice describes a spin loss and efficiency test procedure for Independent Drive Units (FDU & RDU) used in light-duty vehicles. The test procedure is conducted on an axle test rig. The test matrix determines the spin loss and efficiency values at three mileage conditions of the axle and utilizes an accelerated break-in procedure.

This document describes the megawatt-level DC charging system requirements for couplers/inlets, cables, cooling, communication and interoperability. The intended application is for commercial vehicles with larger battery packs requiring higher charging rates for moderate dwell time. A simplified analog safety signaling approach is used for connection-detection to guarantee de-energized state for unmated couplers with superimposed high speed data for EVSE-EV charging control and other value added services.

This document provides an application guide for electric motors that drive aerospace hydraulic pumps. It provides details of the characteristics of electric motors powered by DC, Fixed Frequency AC, and Variable Frequency AC electrical systems. The applications include both military and commercial aircraft.

This document outlines the current state of the art in the understanding of gas in solution in shock absorber oils in unseperated shock absorbers. A literature review, overview of Henry's law, Henry's law coefficients for known gas and oil couples, in-service operational problems, lessons learned, and potential future work will be discussed in the document.

This document outlines historical systems which have used the landing gear as a sensor or installation point for full aircraft weight and balance systems. A number of systems have been developed, installed, certified, and placed in service but few systems remain in regular use. The document will capture the history of these systems, reasons (where known) for their withdrawal from service, and lessons learned.

This document will outline existing best practices in the instrumentation of landing gears for in-service operation (including flight test, operational loads monitoring, etc.).

This report will document Runway Condition Monitoring systems that provide information intended to reduce or eliminate aircraft runway excursions or overruns that may occur as a result of poor runway conditions.

This document describes the approaches taken to define safe-life limits for the management of fatigue in landing gear structures, and the substantiation of those limits through full-scale fatigue testing. The safe-life scatter factors considered in a range of military and civil regulatory standards are also reviewed.