Search Results

The ever increasing popularity of electric vehicles and higher requirement on safety and comfort has led heat pump air conditioning system indispensable in electric vehicle. Many studies have shown that the addition of nano particles contributes to great improvement on thermal conductivity than that of conventional refrigerants. Therefore, the application of the magnetic nanorefrigerant in heat pump air conditioning system has massive potential to heighten the heat transfer efficiency. This paper aims at studying the magnetic nanorefrigerant comprised of the magnetic nano powder Fe3O4 and refrigerant R134a. According to the relevant theoretical analyses and empirical formula, the heat transfer coefficient, density, viscosity, and other physical parameters are calculated approximately. In the heat pump air conditioning system of a certain type of electric vehicle, the special working condition parameters are selected to carry out calculation analysis with numerical analysis software.

The identification of vehicle noise is the basis for studying the acoustic characteristics of vehicles. In this paper, both excitation of noise sources and response of interior noise were identified. Firstly, a transfer path analysis (TPA) model was established to identify the excitation of noise sources, which includes vehicle main noise sources, such as engine, tire, exhaust pipe and muffler. Based on the operational signals and transfer function which were tested in the vehicle semi-anechoic room, the excitation of noise sources was identified using inverse matrix method. Identify result indicated that tires have higher excitation amplitude than engine in high frequency band. Therefore, the transfer path between the tire and the cabin, such as carpet and windshield, should be taken as the focus of acoustic performance improvement. By improving the acoustic material on the transfer path, the loss of sound in the transfer path will be increase.

The application of turbochargers in fuel vehicles brings high-frequency noise, which seriously affects the vehicle's ride comfort. The hiss noise of a turbocharged car is improved in this paper. Firstly, under different operating conditions and whether the air intake system is wrapped, the noise in the vehicle cabin and the driver's right ear is tested, and the noise sources and noise characteristics are identified. Then, the acoustic calculation model of the muffler is established, and the transmission loss (TL) of the original muffler behind the turbocharger (MBT) is calculated. The TL of the muffler is measured by the double-load impedance tube method. The finite element calculation model is verified by comparing the TL of muffler calculated with tested. Thirdly, the MBT is redesigned. The improved muffler significantly improves the performance of eliminating high-frequency noise, and its TL beyond 20 dB is expanded to the band of 1600 ~ 3500 Hz.

In the existing literature concerning the calculation of the output speed of the silicone oil fan clutch and the silicone oil temperature, the theoretical calculation method is all adopted to establish the calculation formulas of moment transmission and silicone oil shear viscous heat by extracting the structural parameters of the clutch model, in order to solve the output speed and silicone oil temperature of the clutch under stable working state. At present, CFD (Computational Fluid Dynamics) numerical simulation method has not been used to solve the problem. In this paper, the CFD simulation method is used for the first time. Considering the change of silicone oil viscosity with temperature, a double-sided slot silicone oil fan clutch was taken as the research object to established the CFD simulation model of hydro-viscous drive to solve the clutch output speed and silicone oil temperature.

Aiming at the problem of middle and low frequency noise absorption, a combined sound-absorbing structure is designed based on porous material and a coiled-up cavity resonance structure. Combined with the sound absorption principle of porous materials and coiled-up cavities, a theoretical analytical model was established. By the finite element method, the sound absorption coefficient curve of the combined structure in a frequency range of 500-2000Hz is calculated, and the correctness of the analytical calculation and the finite element simulation calculation was verified in the impedance tube experiment. The results show that the combined structure has good sound absorption performance in the 500Hz-2000Hz frequency band, and the sound absorption peak appears near the 1108Hz frequency, reaching nearly perfect sound absorption. Compared with a single porous material, the sound absorption performance of the combined structure is better.

A new type ECCVT system is studied. It consists of a rotor and a stator with iron winding, an additive magnetic field adjusting winding, a cup-type rotor with special magnetic pole, inductive slip rings and power electronic controller. Its specialty is that the traditional electric transmission and electromagnetism coincidence are combined and the electricity is transferred unosculantly, so that the power split is realized. The new system also puts up a compact topology, good control and stability by the way of frequency conversion and magnetic field adjusting. The system not only has a wide continuously variable range as the traditional Electric Motor, but also has a high efficiency. Being used on a car, the clutch and starter are omitted. It also can be used as the driving line of the HEV.

Multi-body dynamics simulation is widely used in the dynamic research of constant velocity joints (CVJ). Useful kinematic and dynamic conclusions can be obtained from simulations to replace part of the test process and reduce test costs. In this paper, multi-body dynamics parameterized (MBDP) models of the high-efficiency constant velocity joints are proposed in the software of ADAMS. A friction model and Hertz contact theory are applied to describe the contact status. And the torque transmission efficiency of the kind of high-efficiency CVJ is calculated through the MBDP model. Bench tests of torque transmission efficiency are carried out on the CVJ to verify the calculation accuracy of the multi-body dynamics model. And the test result of high-efficiency joint shows an excellent behavior for efficiency when compared with BJ.

An Inline 4-cylinder engine is equipped with second-order balance shafts. When the engine is running under no-load acceleration conditions, the gear system of the balance shaft generated whine noise. In this paper, an analysis and experiment method for reducing the whine noise is presented. First, a flexible multi-body dynamic model of the engine is established, which includes shaft and casing deformation, micro-modification of the gears. Taking the measured cylinder pressure as input, the load on each gear of balance shaft gear system is calculated. In addition, the influence of tooth surface micro-modification on the meshed noise was analyzed. The results show that the dynamic meshing force between the crank gear and the shim gear is large under the original tooth surface micro-modification parameters, which is the main reason of the whine noise.

Turbulence caused by the blade tip of engine cooling fan is one of important noise generating factors. Existing theoretical researches show that the bionic serrated designs applied at the front and rear edges of fan blades can effectively improve the airflow characteristics and reduce the aerodynamic noise. However, the effect of its application at the blade tip needs to be explored and verified. In this research, vehicle engine fans whose tips are designed and remodeled with different size of triangular serrated edge have been tested on airduct, to explore the fan static pressure and noise that caused by changing of period and amplitude size. The large eddy simulation (LES) and FW-H acoustic analogy method are adopted to calculate the transient noise of each designed fan.

The silicone oil clutch is a device that uses the viscous shear force of silicone oil to transmit torque. Due to the difference in the rotational speed of the driving and driven parts, the silicone oil inside the clutch generates much heat, and the silicone oil temperature increases, resulting in a decrease in viscosity. Therefore, excellent thermal performance is necessary for silicone oil clutch to ensure torque transmission ability. This paper proposes a modeling method for analyzing the thermal performance of a silicone oil clutch. Firstly, the temperature measurement test for the silicone oil clutch is carried out by using wireless temperature measurement equipment. The driven speed, silicone oil temperature, and the temperature of different areas of the clutch shell are measured under different driving speeds.

The thermal management system, which is used to improve driving safety and thermal comfort, is one of the most important systems in electric vehicles. In recent years, researchers have coupled the heat pump system and the battery cooling system to effectively improve the heating COP (Coefficient of Performance). Therefore an accurate dynamic model of thermal management system plays a key role in investigating system performance and optimal control strategies. In this paper, an electric vehicle thermal management system based on four-way valve heat pump system is designed. The moving boundary method is improved by considering the unsteady flow of the external fluid, and then a 13-order dynamic model of the thermal management system is established. Firstly, the control equations of evaporator, condenser and chiller are derived according to the principle of conservation, and then a dynamic model of thermal management system is established in Simulink.

A rumbling noise is audible in a vehicle passenger compartment during acceleration. Mechanism detail of the rumbling noise is studied. A series of preliminary transfer path experiments investigation on chassis dynamometer shows that the interior rumbling noise is mainly induced by abnormal crankshaft impact at particular crank angle. Spectrum analysis indicates that high level half order harmonic components significantly affects the rumbling noise. Multi-body dynamics model of the powertrain is developed to further investigate the root cause of the abnormal crankshaft impact. Experiment results are used to verify the numeric model. High deviation of main bearing forces at the crank angle 0° to 180° after the Fire Top Dead Center of the no.l cylinder is considered to fundamentally induces the high level half order components. The force ripple coupled with the crankshaft resonance induces the crankshaft rumbling.

With the popularity of battery electric vehicles, the engine of the vehicle disappears, so the problem of road noise in cars is becoming more and more prominent. Road noise into the car can be divided into structure-borne noise and airborne noise, this paper only focuses on the airborne noise above 500Hz, completely ignoring the structure-borne noise. A transfer path analysis model with “Intermediate Response Points” is proposed to accurately represent the transfer path of each airborne noise through the setting of “Intermediate Points”. In the Vehicle Semi-Anechoic Room With 4×4 NVH Chassis Dyno, it is possible to create a working condition with only four tires running, so only the tire noise is considered in this paper. The frequency response function is tested in the Semi-Anechoic Chamber and the operating data is tested in the Vehicle Semi-Anechoic Room With 4×4 NVH Chassis Dyno.

The driving pulley is often used as a Torsional Vibration Damper (TVD) for the crankshaft in the front end accessory drive (FEAD) system. Although the crankshaft torsional vibrations are dampened, they are transmitted to the belt transmission and therefore to the driven accessories. The isolation pulley is a new device to reduce the belt tension fluctuation by isolating the belt transmission from the crankshaft torsional vibrations. A five-pulley system with isolation pulley is presented and a non-linear model is established to predict the dynamic response of the pulleys, tensioner motion, tension fluctuation and slippage. The model works in the time domain with Runge-Kutta time-stepping algorithm. The numerical simulation results of harmonic excitations show that the amplitudes of the belt tension fluctuation and the vibrations of each component are reduced significantly. Moreover, the effect of isolation pulley parameters on the system natural frequencies is demonstrated.

During the operation of the automotive drive shaft system, the ball-type universal joint will generate a secondary torque, which will affect the torque transmission of the automotive drive shaft system and the comfort of the automobile. Under the influence of the internal friction of the ball-type universal joint, the secondary torque generates a torque component on the plane where the working angle is located and the plane perpendicular to the working angle. To effectively calculate and analyze the secondary torque, this paper establishes a multi-body dynamic model of the ball-type universal joint. At the same time, the secondary torque of the ball-type universal joint is measured by the NVH multi-function test bench, which verifies the validity of the multi-body dynamic model. In order to improve the analysis efficiency of the secondary torque, a proxy model of the secondary torque of the ball-type universal joint is established based on the multi-body dynamic model.

In the variable axial transmission system of an automobile, the power output of the segmented transmission shaft changes, which affects the vibration of the rear axle to a certain extent. As an important component of the drive shaft system, the intermediate support has an important effect on reducing the vibration transmission path of the drive shaft and the vibration of the rear axle system. In this paper, the vibration characteristics of the intermediate support of a certain vehicle's transmission shaft and the transmission shaft system are studied, and the vibration damping performance of the intermediate support rubber is theoretically analyzed and design optimized. In order to solve the vibration problem in the high frequency range of this car, a rubber pad was added at the position of the installation hole of the intermediate support bracket assembly to form a structure with double-layer vibration isolation effect, and the stiffness of this structure was optimized.

To reduce the noise in the frequency range of 100Hz~1000Hz, a metamaterial structure composed of lightweight frame, hard membrane-like material and added mass is proposed in this paper. The advantage of this structure is that it is lightweight and the membrane-like material does not need to be stressed in advance. Finite element method (FEM) and experiment are used to investigate the sound transmission loss (STL) performance of the metamaterial structure. The results show that the peak STL is caused by the local resonance of the added mass and the membrane-like material. The valley versus frequency results from the resonance frequencies of metamaterial structure, and it is divided into three resonance frequencies: resonance frequencies from added mass, membrane-like material and frame.

In this paper, the influence of the decoupler-cage structure on the hitting noise of the hydraulic mount is studied, the abnormal noise of the hydraulic mount is mainly caused by the collision impact between the decoupler and the cage, the hitting noise was simulated and evaluated using calculation and experiment. a finite element model of the collision impact between the decoupler and the cage is developed, and an explicit finite element analysis is performed to obtain the time history of the vibration acceleration of the model, which is used as the boundary condition of the noise analysis. The acoustic boundary element method is used to analyze the impact noise of the decoupler-cage, and the frequency domain distribution characteristics of the impact sound pressure are obtained. The influence of different decoupler structure on the hitting noise is studied, and the recommended values for each parameter for a structure are given.

As one of the key components of the heat pump system, the electronic expansion valve mainly plays the role of throttling and reducing pressure in the heat pump system. The refrigerant flowing through the orifice will produce complex phase change. It is of great significance to study the internal flow field by means of CFD calculations. Firstly, a three-dimensional fluid model is established and the mesh is divided. Secondly, the phase change model is selected, the material is defined and the boundary conditions are determined. According to the principle of the fluid passing through thin-walled small holes, the flow characteristics of electronic expansion valve are theoretically analyzed. Then the flow characteristics of expansion valve are numerically calculated, and a bench for testing mass flow rate of the expansion valve is built. Then the theoretical value, CFD value and experimental value are compared to verify the correctness of the established three-dimensional fluid model.

The distributed parameter method is used to establish the dynamic simulation model of the electric vehicle thermal management system and various parts, and the finite difference method is used to solve the model. A thermal management system model with same structure is established by AMESIM, and the accuracy of the dynamic simulation model is verified by comparing the deviation of the calculation result between this dynamic simulation model and AMESIM. Based on the established model, the influence of expansion valve opening on the temperature of battery pack and the influence on the heating comfort of the cabin were studied. A control strategy for the rapid cooling of the battery pack was proposed. The results show that the model established by the distributed parameter method provides quite well agreement with commercial equivalent software and can well reflect the flow state of the refrigerant in different zones of the same component.