Search Results

During the operation of the ball joint, its service life and transmission efficiency are affected by the internal friction. Taking the ball joint as the research object, based on fractal theory, the friction between the steel ball and the raceway inside the ball joint of an automotive drive shaft system is studied in this paper. During the analysis, the friction between the steel ball and the arc raceway is regarded as the friction between a sphere and an arc raceway surface. In order to describe the friction state more accurately, this paper proposes a correction coefficient to modify the distribution function of contact asperities in the plane, and obtains the distribution function of contact asperities between the sphere and the arc raceway surface. The correction coefficient is related to the load, the size parameters and the material parameters of the steel ball and the raceway.

Experimental investigation on a high speed single-cylinder diesel engine has shown that a gas-pressure stabilizer in the exhaust system has obvious effect upon engine performance. Two types of such gas pressure stabilizers were tested, and a reduction of about 0.5% to 2% in fuel consumption rate was achieved, which was mainly dependent on the type of stabilizer employed and was more significant under higher speed conditions.

An analysis of the vehicle braking, combining with the linear relation between wear and frictional work already investigated, was used to establish a wear equation. Initial braking velocity, the number of brakings per 1 km and pad thickness loss per 1000 km were determined by using taxis with identical car types and identical pad qualities. Based on the averaged experimental results and some normal braking conditions, the calculated average apparent specific wear rate through the equation was unexpectedly found to decrease firstly and then increase with the increase of average initial braking velocity. The pad friction properties relevant to the equation analysis were tested by using a dynamometer, followed by measuring wear as a function of temperature at three different initial velocities that equal the average initial braking velocities respectively.

Tuned mass dampers (TMD) are frequently used in vehicles to resolve vibration and interior booming noise issues arising from powertrain's vibration and road excitation. This paper describes a driveshaft NVH case study in which analysis and test were used to solve the NVH problem. A TMD simulation package that utilizes a database of measured elastomeric material propertied. This facilitates the designing of optimized damper systems for a wide variety of vehicle applications. The simulation software takes into account frequency effects on elastomer properties while designing dampers. And the approach has proven to accurately predict performance in vehicles prior to manufacture. Rules of thumb for TMD design are discussed including locations for placement of dampers in automotive structures, determining the needed mass, and measurements and simulations that can greatly improve the success and reducing time-cost for TMD design.

The ever increasing popularity of electric vehicles and higher requirement on safety and comfort has led heat pump air conditioning system indispensable in electric vehicle. Many studies have shown that the addition of nano particles contributes to great improvement on thermal conductivity than that of conventional refrigerants. Therefore, the application of the magnetic nanorefrigerant in heat pump air conditioning system has massive potential to heighten the heat transfer efficiency. This paper aims at studying the magnetic nanorefrigerant comprised of the magnetic nano powder Fe3O4 and refrigerant R134a. According to the relevant theoretical analyses and empirical formula, the heat transfer coefficient, density, viscosity, and other physical parameters are calculated approximately. In the heat pump air conditioning system of a certain type of electric vehicle, the special working condition parameters are selected to carry out calculation analysis with numerical analysis software.

Because the power unit of electric vehicle has large torque, the rubber mount of electric vehicle is fully compressed under the condition of full throttle acceleration. When designing the mount of electric vehicle, the dynamic-to-static stiffness ratio of mount under the case should be as low as possible to improve the vibration isolation rate of the mount. In this paper, a method for calculating the high frequency dynamic characteristics of rubber isolators under different preloads is presented. Firstly, the dynamic characteristics of rubber specimens under various shear pre-strains were tested. The test results show that the dynamic stiffness of specimen decreases at first and then increases with the increase of shear strain. The viscoelastic parameters of rubber in frequency domain under different pre-strain were identified according to the experimental data. Secondly, a finite element modeling method was proposed.

Aiming at the problem of middle and low frequency noise absorption, a combined sound-absorbing structure is designed based on porous material and a coiled-up cavity resonance structure. Combined with the sound absorption principle of porous materials and coiled-up cavities, a theoretical analytical model was established. By the finite element method, the sound absorption coefficient curve of the combined structure in a frequency range of 500-2000Hz is calculated, and the correctness of the analytical calculation and the finite element simulation calculation was verified in the impedance tube experiment. The results show that the combined structure has good sound absorption performance in the 500Hz-2000Hz frequency band, and the sound absorption peak appears near the 1108Hz frequency, reaching nearly perfect sound absorption. Compared with a single porous material, the sound absorption performance of the combined structure is better.

Uniaxial fatigue tests of rubber dumbbell specimens under different mean and amplitude of strain are carried out. An Extreme Learning Machine (ELM) model optimized by Dragonfly Algorithm (DA) is proposed to predict the fatigue life of rubber based on measured rubber fatigue life data. Mean and amplitude of strain and measured rubber fatigue life are taken as input variables and output variables respectively in DA-ELM model. For comparison, genetic algorithm (GA) and particle swarm optimization (PSO) are used to optimize ELM parameters, and GA-ELM and PSO-ELM models are established. The comparison results show that DA-ELM model performs better in predicting the fatigue life of rubber with least dispersion. The coefficients of determination for the training set and test set are 99.47% and 99.12%, respectively. In addition, a life prediction model equivalent strain amplitude as damage parameter is introduced to further highlight the superiority of DA-ELM model.

In order to enhance the efficiency of durability testing of automobile parts, a time-frequency domain accelerated editing method of road load time series of rubber mount on powertrain was discussed. Based on Stockwell Transform method and Accumulative Power Spectral Density, a new time-frequency domain accelerated editing method (ST-APSD) was proposed. The accumulative power spectral density was obtained by ST of the load time series signal of automobile powertrain rubber mounting force which is acquired by the real vehicle in the test field. Based on the accumulative power spectral density, the threshold value was proposed to identify and delete the small damage load fragments, and then the acceleration spectrum was obtained.

The dynamic characteristics of hydraulic damping rubber isolators (such as hydraulic bushing and hydraulic mount) are related to excitation amplitude and frequency. Based on the lumped parameter model of hydraulic damping rubber isolator, a unified linear model of complex stiffness is derived and its deficiency is pointed out. Based on the derived linear model, this paper considers the nonlinear damping of inertia channel and the nonlinear stiffness of the upper chamber of the hydraulic damping rubber isolator, so as to establish a new nonlinear model, which can reflect the amplitude and frequency dependence of the dynamic characteristics of the hydraulic damping rubber isolator. Finally, the nonlinear model is used to analyze the dynamic response of hydraulic damping rubber isolator under harmonic excitation and random excitation respectively, and the results are compared with the test results.

In the field of low-frequency noise control, the acoustic metamaterials have received extensive attention from researchers. However, the existing work mainly focuses on small structures with fixed boundaries, which is quite different from engineering applications. Based on the membrane-type acoustic metamaterials, this paper uses a rigid thin plate to replace the tensioned membrane, design and manufacture of two new types of local resonance structure and studies their sound insulation properties. First, the metamaterial samples with a small size of 100mm in diameter and a large-size square with a side length of 506mm were produced, and the sound TL of the two was tested through the impedance tube and the reverberation chamber-anechoic chamber, respectively. The results show that the new structure can form an obvious sound insulation frequency band at low frequencies. Based on the finite element method, a metamaterial acoustic transmission loss calculation model is established.

Welding deformation of aluminum alloy is an urgent problem to be solved, it affects the performance and service life of welding products. In this research, in order to compute welding deformation and residual stress, a finite element model of 6061-T6 aluminum alloy was established. The efficiency and the accuracy of the welding residual stress calculation and the welding deformation were significantly improved. By comparing the temperature field and the displacement field of simulation and experiment, the finite element model was validated. Through finite element analysis, Heat input and welding times have important effects on welding deformation and residual stress was found. The welding deformation law and the residual stress distribution law were proposed, after cooling of the welding seams, the plates collapsed to the other side of the heat source along the vertical direction, the welding deformation tendency was heightened by double-sided welding.

A new proportional electromagnetic dynamic vibration absorber (EDVA) is proposed for control of engine vibration during idling. The device consists of an electromagnetic actuator attached to the primary structure through elastic element, where the driving force pair is implemented between the reaction-mass and the primary structure. The design of the proportional electromagnetic actuator is realized considering the geometric parameters of the core to achieve nearly constant magnetic force over a broad range of its dynamic displacement but proportional to square of the current. A methodology is proposed to achieve magnetic force proportional to square of current and consistent with the disturbance frequency. The proportional EDVA is subsequently applied to a single-degree-of-freedom primary system with an acceleration feedback control algorithm for attenuation of primary system vibration in a frequency band around the typical idling vibration frequencies.

The elliptically shaped bearing (ESB) with a rigid, elliptical inner race and a flexible, thin-walled outer race is the most easily damaged core component of harmonic drive. The ESB rotates under cycle load of alternating stress due to its special elliptic structure. Hence, the fault features of ESB such as fatigue spalling and pitting are apt to be concealed by the excitation of impulses caused by alternating between major axis and minor axis. In order to diagnose the fault on raceway surfaces of ESB, a new method of CMWT-FH based on Continuous Morlet Wavelet Transform (CMWT) and FFT-based Hilbert (FH) spectrum analysis is proposed to extract the fault feature.

For traditional rubber isolators, the dynamic stiffness increases significantly with the increase of excitation frequency and will have a peak value, which is called "internal resonance" phenomenon. This paper investigates a double-isolation rubber isolator, which consist of two rubber bushings and additional mass. It can be applied to improve the NVH (Noise, Vibration and Harshness) performance at high frequency of electric vehicles. The equivalent mechanical model and mathematical model of the double-isolation rubber isolator are established. Then, the finite element analysis (FEA) model is established, and we calculate the drive point dynamic stiffness and cross point dynamic stiffness of the inner bushing, outer bushing and the entire double-isolation rubber isolator.

The breaking torque is an essential property that identifies the strength of driveshafts under high torque loads. In the breaking torsion test, the constant velocity joint of the driveshafts is usually loaded slowly at a very slow rotating speed under a specific joint angle until it breaks. Under different joint angles, the Rzeppa type constant velocity joint, namely ball joints (BJ), will break at different positions and with different torques. Common results of fracture position include the shaft of the outer race, the shell of the outer race, and the cage column. Simultaneously, the plastic deformation caused by compressive stress occurs at the specific position of the ball track and the cage. In order to analyze the failure reason of the ball joint under a larger joint angle, the quasi-static finite element simulations and test methods are used to analyze the damage caused by stress distribution based on material properties.

Membrane-type acoustic metamaterials consist of a tensioned membrane fixed on the frame and an additional mass attached to the membrane. The sound insulation performance of membrane-type acoustic metamaterials is much better than the acoustic mass law predictions at transmission loss (TL) peak frequencies. In this paper, an equivalent mechanical model of membrane-type metamaterials is established. Through the vibration analysis of the membrane with tensile force as the main elastic restoring force, an approximate estimation method of the TL peak frequency of Membrane-type acoustic metamaterials is proposed, the effects of membrane tension, membrane size, mass and size of additional mass on the peak frequency of TL were analyzed quantitatively. The COMSOL software was used to establish a finite element analysis model and calculate the TL curve of the metamaterial at a frequency of 100-1600 Hz.

Tortuosity, viscous characteristic length and thermal characteristic length are three important parameters for estimating the acoustic performance of porous materials, and it is usually measured by ultrasonic measurement technology, which is costly. In this paper, a method for identifying the tortuosity, viscous characteristic length and thermal characteristic length for the porous fiber materials mixed with kapok fiber and two kinds of other fiber materials is proposed. The tortuosity is calculated by using the porosity and high-frequency normal sound absorption coefficient of porous materials. According to the normal sound absorption coefficient curve of porous materials under plane wave incidence, viscous characteristic length and thermal characteristic length are identified through the Johnson-Champoux-Allard-Lafarge (JCAL) model and genetic algorithm by using the measured parameters, the calculated tortuosity and static thermal permeability.

To reduce the noise in the frequency range of 100Hz~1000Hz, a metamaterial structure composed of lightweight frame, hard membrane-like material and added mass is proposed in this paper. The advantage of this structure is that it is lightweight and the membrane-like material does not need to be stressed in advance. Finite element method (FEM) and experiment are used to investigate the sound transmission loss (STL) performance of the metamaterial structure. The results show that the peak STL is caused by the local resonance of the added mass and the membrane-like material. The valley versus frequency results from the resonance frequencies of metamaterial structure, and it is divided into three resonance frequencies: resonance frequencies from added mass, membrane-like material and frame.

As an important vibration damping element in automobile, the rubber mount can effectively reduce the vibration transmitted from the engine to the frame. In this study, a method of parameters identification of Mooney-Rivlin model by using surrogate model was proposed to more accurately describe the mechanical behavior of mount. Firstly, taking the rubber mount as the research object, the stiffness measurement was carried out. And then the calculation model of the rubber mount was established with Mooney-Rivlin model. Latin hypercube sampling was used to obtain the force and displacement calculation data in different directions. Then, the parameters of the Mooney-Rivlin model were taken as the design variables. And the error of the measured force-displacement curve and the calculated force-displacement curve was taken as the system response. Two surrogate models, the response surface model and the back-propagation neural network, were established.