Search Results

During the last years mechatronic systems developed into one of the biggest drivers of innovation in the automotive industry. The start of production of systems like dual clutch transmission, lane departure warning systems and active suspensions proves this statement. These systems have an influence on the longitudinal, steering and vertical dynamics of the vehicle. That is why the interaction on vehicle level is crucial for an optimal result in the fields of efficiency, comfort, safety and dynamics. To optimize the interaction of mechatronic systems, in this paper a new test rig concept for a complete vehicle is presented. The so-called Car-in-the-Loop-concept is capable of realistically reproducing the loads, which act on the powertrain, the steering and the suspension during a test drive.

Magnetic Resonance Velocimetry (MRV) measurements are performed in 1:1 scale models of a single-cylinder optical engine to investigate the differences in the inlet flow due to geometrical changes of the cylinder head. The models are steady flow water-analogue of the optical IC engine with a fixed valve lift of 9.21 mm to simulate the induction flow at 270° bTDC. The applicability of MRV to engine flows despite the differences in experimental operating parameters between the steady flow model and the optical IC engine are demonstrated and well addressed in this manuscript and in a previous work [1]. To provide trust into the MRV measurements, the data is validated with phase-averaged particle image velocimetry (PIV) measurements performed within the optical engine. The main geometrical changes between the cylinder heads include a variation of intake valve diameter and slight modifications to the exit of the intake port.

Driving cycles play a fundamental role in the design of components, in the optimization of control strategies for drivetrain topologies, and in the identification of vehicle properties. The focus on a single or a few test cycles results in a risk of non-optimal or even poor design regarding the real usage profiles. Ideally, multiple different driving cycles that are representative of the real and scattering operating conditions are used. Therefore, tools for the stochastic generation of representative driving cycles are required, and many works have addressed this issue with different approaches. Until now, the stochastic generation of representative testing cycles has been limited to low dimensionality, and only a few works have studied higher dimensionality using Markov chain theory. However, it is mandatory to create tools that can stochastically generate multidimensional cycles incorporating all relevant operating conditions and maintaining signal dependency at the same time.

Particle image velocimetry measurements of the in-cylinder flow in an optically accessible single-cylinder research engine were taken to better understand the effects of intake pressure variations on the flow field. At a speed of 1500 rpm, the engine was run at six different intake pressure loads from 0.4 to 0.95 bar under motored operation. The average velocity fields show that the tumble center position is located closer to the piston and velocity magnitudes decrease with increasing pressure load. A closer investigation of the intake flow near the valves reveals sharp temporal gradients and differences in maximum and minimum velocity with varying intake pressure load which are attributed to intake pressure oscillations. Despite measures to eliminate acoustic oscillations in the intake system, high-frequency pressure oscillations are shown to be caused by the backflow of air from the exhaust to the intake pipe when the valves open, exciting acoustic modes in the fluid volume.

The thorough understanding of the effects due to the fuel direct injection process in modern gasoline direct injection engines has become a mandatory task to meet the most demanding regulations in terms of pollutant emissions. Within this context, computational fluid dynamics proves to be a powerful tool to investigate how the in-cylinder spray evolution influences the mixture distribution, the soot formation and the wall impingement. In this work, the authors proposed a comprehensive methodology to simulate the air-fuel mixture formation into a gasoline direct injection engine under multiple operating conditions. At first, a suitable set of spray sub-models, implemented into an open-source code, was tested on the Engine Combustion Network Spray G injector operating into a static vessel chamber. Such configuration was chosen as it represents a typical gasoline multi-hole injector, extensively used in modern gasoline direct injection engines.

A unique concept for a multi-body test rig enabling the simulation of longitudinal, steering and vertical dynamics was developed at the Institute for Mechatronic Systems (IMS) at TU Darmstadt. A prototype of this IMS test rig is currently being built. In conjunction with the IMS test rig, the Vehicle Terrain Performance Laboratory (VTPL) at Virginia Tech further developed a full car, seven degree of freedom (7 DOF) simulation model capable of accurately reproducing measured displacement, pitch, and roll of the vehicle body due to terrain excitation. The results of the 7 DOF car model were used as the reference input to the multi-body IMS test rig model. The goal of the IMS/VTPL joint effort was to determine whether or not a controller for the IMS test rig vertical actuator could accurately reproduce wheel displacements due to different measured terrain constraints.

A comparison between a hydraulic engine mount and a mixed mode magnetorheological (MR) fluid engine mount is presented. MR fluid is a smart material that changes viscosity in the presence of a magnetic field. In other words, without the presence of a magnetic field, the fluid is classified as a Newtonian fluid, however; with the presence of a magnetic field, the fluid becomes classified as a Bingham plastic. The working modes of the MR mount are squeeze and flow. Hydraulic mounts were developed to address the conflicting requirements of the engine vibration profile. The engine vibration profile can be classified as large displacement in the low frequency range and small displacement in the high frequency range. The hydraulic mount used in this study is an as received OEM mount. The elastomeric top and bottom of the hydraulic mount were used to create the MR mount. In the paper, the advantages and disadvantages of each mount are discussed in detail.

The chassis are subject to both road profile and engine or pump/motor vibration when a vehicle is moving on the road. The suspension is developed to reduce the effect of the road conditions to the chassis. The vibration from engine or pump/motor of hydraulic hybrid vehicles (HHV) will be also transmitted to the chassis and needs to be isolated. A mixed mode magnetorheological (MR) fluid mount is presented to isolate force vibration for a two degree of freedom (DOF) model based on quarter car concept. The MR fluid mount is designed to work in flow mode and squeeze mode separately and simultaneously. The skyhook control for the MR fluid mount is also been designed and simulated. Both displacement transmissibility and force transmissibility for each mode and for combined modes have been obtained. These simulation results present a basis for designing a more effective controller to control both the displacement transmissibility and force transmissibility.

An online and real-time Condition Prediction system, so-called lifetime monitoring system, was developed at the Institute for Mechatronic Systems in Mechanical Engineering (IMS) of the TU Darmstadt, which is intended for implementation in standard control units of series production cars. Without additional hardware and only based on sensors and signals already available in a standard car, the lifetime monitoring system aims at recording the load/usage profiles of transmission components in aggregated form and at estimating continuously their remaining useful life. For this purpose, the dynamic transmission input and output torques are acquired realistically through sensor fusion. In a further step, the lifetime monitoring system is used as an input-module for the introduction of innovative procedures to more load appropriate dimensioning, cost-efficient lightweight design, failure-free operation and predictive maintenance of transmissions.

Recently, the European Union has adopted a new regulation on Real-Driving-Emissions (RDE) and also China is considering RDE implementation into new China 6 legislation. The new RDE regulation is focused on measuring nitrogen oxides (NOx) and particulate number (PN) emissions of both light-duty gasoline and diesel vehicles under real world conditions. A supplemental RDE test procedure was developed for European type approval, which includes on-road testing with cars equipped with portable emission measurement systems (PEMS). This new regulation will significantly affect the engine calibrations and the exhaust gas aftertreatment. In this study the impact of the new RDE regulation on two recent EU 6b certified turbocharged direct injected gasoline vehicles has been investigated. A comparison of several chassis dyno drive cycles with two new defined on-road RDE cycles was performed.

A method for estimating the vehicle mass in real time is presented. Traditional mass estimation methods suffer due a lack of knowledge of the vehicle parameters, the road surface conditions and most importantly the effect of the vehicle transmission. To resolve these issues, a method independent of a vehicle model is utilized in conjunction with a drivetrain output torque observer to obtain the estimate of the vehicle mass. Simulations and experimental track tests indicate that the method is able to accurately estimate the vehicle mass with a relatively fast rate of convergence compared to traditional methods.

The Institute for Mechatronic Systems in Mechanical Engineering (IMS) designed a concept for a test rig, which enables the simulation of longitudinal, steering and vertical dynamics for a complete vehicle under laboratory conditions. The main part of the test rig concept is a shaft, which contains three constant velocity joints and two ball-spline supported length compensations. It connects the wheel hub of the test car to an electric motor. In addition a linear actuator is mounted to the middle part of the shaft and a hydraulic actuator replaces the suspension strut. These actuators can load the longitudinal, steering and vertical degree of freedom of the test car according to simulated driving maneuvers. A prototype of this concept is being built at the IMS lab. Beginning with a precise explanation of the test rig concept this paper discusses the control strategy for the rotational speed of the wheel hub of the car mounted on the test rig based on a simulation.

Referring to the transmission development, three different classifications of the power train are useful. These are the conventional power train with combustion-engined drive of the wheels, the electric power train with electromotive drive of the wheels and the hybrid power train with both types of drive. Due to this division, the micro hybrid belongs to the conventional power train while the serial hybrid is classified with the electric power train. Subdivisions of the electric power train are the decentralized drives near the axle shafts or the wheel hub drive and the central drive with differential. The choice of the electric motor is dependent on different influences such as the package, the costs or the application area. Furthermore the execution of the transmission system does influence the electric motor. Wheel hub drives are usually executed on wheel speed level or with single ratio transmission.

Faults in the intake and exhaust path of turbocharged common-rail Diesel engines can lead to an increase of emissions and performance losses. Standard fault detection strategies based on plausibility checks and trend checking of sensor data are not able to detect and isolate all faults appearing in the intake and exhaust path without employing additional sensors. By applying model based methods a limited sensor configuration can be used for fault detection. Therefore a model based fault diagnosis concept with parity equations is considered, [1]. In this contribution the fault diagnosis system, which comprises semi-physical thermodynamic turbocharger model, models of gas pressure in the intake and exhaust manifold, residual generation, residual to symptom transformation and fault diagnosis is presented.

The goal of constructing squeal free brakes is still difficult to achieve for design engineers. There are many measures that are beneficial to avoid or decrease brake squeal, examples are the increase in damping and the introduction of asymmetries in the brake rotor. For an efficient design process these measures have to be quantified. This is difficult due to the high complexity of the system which is caused by the contact conditions and the complicated properties of the pad material which consists of a vast amount of different components. The attempt presented in this paper is to use fundamental models of the excitation mechanism for brake squeal in order to quantify the rate of asymmetry and damping required to get far away from the squeal boundary. The relation can be helpful to generate adequate objective functions for a systematic structural optimization of brake rotors against squeal and can be used as a design guideline.

Spray angle and penetration length data were taken under cold start conditions for a Direct Injection Spark Ignition engine to investigate the effect of transient conditions on spray development. The results show that during cold start, spray development depends primarily on fuel pressure, followed by Manifold Absolute Pressure (MAP). Injection frequency had little effect on spray development. The spray for this single hole, pressure-swirl fuel injector was characterized using high speed imaging. The fuel spray was characterized by three different regimes. Regime 1 comprised fuel pressures from 6 - 13 bar, MAPs from 0.7 - 1 bar, and was characterized by a large pre-spray along with large drop sizes. The spray angle and penetration lengths were comparatively small. Regime 2 comprised fuel pressures from 30 - 39 bar and MAPs from 0.51 - 0.54 bar. A large pre-spray and large drop sizes were still present but reduced compared to Regime 1.

The “Two-Drive-Transmission with Range-Extender” (called DE-REX) is an innovative hybrid powertrain concept using two electric motors and an internal combustion engine. The two electric motors are permanent magnet synchronous motors with a maximum power of 48 kW each. As combustion engine a 3 cylinder, turbocharged engine with a power of 65 kW is used. The aggregates are coupled to a transmission whose layout is characterized by consisting of two parallel 2-speed sub-transmissions. This layout offers a high flexibility and enables both parallel and series hybrid driving. The hybrid control unit (HCU) has to select the optimal driving mode and power distribution between the aggregates in regard to in some extend competing objectives like efficiency, emissions or driving comfort. In particular, the operation of the internal combustion engine with only two gear ratios is challenging.

Developing an energy-efficient powertrain system is a solution for environment-friendly vehicles. Furthermore, it also enhances the performance of vehicles. In powertrain system, transmission plays an important role in terms of vehicle dynamic performance and energy consumption. Therefore, a lot of researches have been conducted on modelling power losses inside the transmission. Basically, the power losses in transmission consist of bearing losses, drag torque losses on gear blank that is immersed in the oil and gear mesh losses due to the sliding frictional force on gear flank. According to some experiments in the latest literatures, power losses of synchronizers cannot be neglected, when its shift sleeve is in neutral position. Principally, power losses of synchronizers in neutral position mainly come from load independent drag torque.

The scope of this work is to propose a methodology to define multicomponent surrogate mixtures which describe the main evaporation characteristics of real gasoline fuels. Since real fuels are commonly complex mixtures with hundreds or thousands of hydrocarbons, their exact composition is generally not known. Only global characteristics are standardized. An accurate modeling of such complex mixtures in 3D-CFD requires the definition of a suitable surrogate. So far, surrogate mixtures have mostly been defined based on their combustion properties, such as ignition delay or burning velocity, irrespective of their evaporation characteristics. For this reason, in this work, a systematic study is carried out to develop a methodology to define mixtures of representative components that mimic the evaporation behavior of real fuels.

In this investigation two different nonlinear dynamic black box modelling approaches are compared. The purpose of the models is to reproduce the transient gearshift process. The models are used to compute the torque at the sideshafts, which is highly correlated to the gearshift comfort. The first model is a Gaussian process (GP) model. The GP is a probabilistic, non-parametric approach, which is additionally capable to compute the confidence interval of the simulated output signal. The second black box model uses the artificial neural net (ANN) approach. In addition to training algorithms the resulting model configurations for both black box approaches are shown in this investigation. Furthermore the empirical error of both modeling approaches is compared to the predictive variance of the GP model and to the intrinsic uncertainty of the gearshift process.