Search Results

Studying the kinetic and kinematics of the rim-tire combination is very important in full vehicle simulations, as well as for the tire design process. Tire maneuvers are either quasi-static, such as steady-state rolling, or dynamic, such as traction and braking. The rolling of the tire over obstacles and potholes and, more generally, over uneven roads are other examples of tire dynamic maneuvers. In the latter case, tire dynamic models are used for durability assessment of the vehicle chassis, and should be studied using high fidelity simulation models. In this study, a three-dimensional finite element model (FEM) has been developed using the commercial software package ABAQUS. The purpose of this study is to investigate the tire dynamic behavior in multiple case studies in which the transient characteristics are highly involved.

The road profile has been shown to have significant effects on various vehicle conditions including ride, handling, fatigue or even energy efficiency; as a result it has become a variable of interest in the design and control of numerous vehicle parts. In this study, an integrated state estimation algorithm is proposed that can provide continuous information on road elevation and profile variations, primarily to be used in active suspension controls. A novel tire instrumentation technology (smart tire) is adopted together with a sensor couple of wheel attached accelerometer and suspension deflection sensor as observer inputs. The algorithm utilizes an adaptive Kalman filter (AKF) structure that provides the sprung and unsprung mass displacements to a sliding-mode differentiator, which then yields to the estimation of road elevations and the corresponding road profile along with the quarter car states.

Autonomous guided vehicles, called AGVs, are important components of factory automation and manufacture system integration that requires both technical and management skills. In this paper, an AGV prototype equipped with IR detectors and IR range sensors is programming to follow a route line on the floor and avoid some obstacles on the way. The motion of the experimental AGV is promote by two DC motor with build-in gearbox, working with simultaneous PWM control in closed-loop operation. This AGV is designed to operate in environments such as offices and shop floor, in order to carry light loads on flat surfaces and ramps with positive and negative inclination. Simulations tests with ADAMS® are compared with some experimental results in order to validate the model and the prototype approaches.

Restrictions on track testing, combined with advances in technology, have contributed to an increased dependence on sensors and data acquisition for diagnosing problems and improving performance in motorsports vehicles. This dependence has created a new set of challenges for race engineers to collect quality data from a vehicle at the track. Successful 7- or 8-post shaker rig testing is highly dependent on the quality of the data acquired at the track. An improperly configured data acquisition system can actually be worse than a faulty sensor. This paper highlights a few of the most common problems in motorsports data acquisition: aliasing and sample rate selection. The effects of these problems are described for typical suspension sensors such as accelerometers, shock potentiometers, load cells, and laser ride height sensors. An experimental case study is presented to explain the implications of these problems.

This study outlines a protocol for image data collection acquired from human volunteers. The data set will serve as the foundation of a consolidated effort to develop the next generation full-body Finite Element Analysis (FEA) models for injury prediction and prevention. The geometry of these models will be based off the anatomy of four individuals meeting extensive prescreening requirements and representing the 5th and 50th percentile female, and the 50th and 95th percentile male. Target values for anthropometry are determined by literature sources. Because of the relative strengths of various modalities commonly in use today in the clinical and engineering worlds, a multi-modality approach is outlined. This approach involves the use of Computed Tomography (CT), upright and closed-bore Magnetic Resonance Imaging (MRI), and external anthropometric measurements.

This study pertains to motion control algorithms using statistical calculations based on relative displacement measurements, in particular where the rattle space is strictly limited by fixed end-stops and a load leveling system that allows for roll to go undetected by the sensors. One such application is the cab suspension of semi trucks that use widely-spaced springs and dampers and a load leveling system that is placed between the suspensions, near the center line of the cab. In such systems it is possible for the suspension on the two sides of the vehicle to settle at different ride heights due to uneven loading or the crown of the road. This paper will compare the use of two moving average signals (one positive and one negative) to the use of one root mean square (RMS) signal, all calculated based on the relative displacement measurement.

Nano-silver sintered bonding was carried out at 275°C and under 3MPa pressures, and soldering in a vacuum reflowing oven to reduce voiding. Both joints are subject to large shear stresses due to the mismatch in coefficients of thermal expansion (CTE) between the chip and the substrate. In this study, residual stresses in the chip-on-substrate assemblies were determined by measuring the bending curvatures of the bonded structures. An in-house optical setup measured the bending curvatures using a thin-film stress measurement technique. From the measured bending curvatures and the mechanical properties of the constituent materials, residual stresses were calculated. The thermo-mechanical reliabilities of both joining techniques were tested by thermal cycling. The chip assemblies were cycled between -40°C and 125°C (100 minutes of cycle time, 10 minutes of dwell time) and the changes in their bending curvatures were measured.

The finite element method (FEM) is used daily in the automotive industry for such purposes as reducing the time of product development and improving the design based on analysis results, followed by later validation by tests in the laboratory and on the proving ground. This paper will present some of the methodology used to develop automotive components by finite element analysis, including procedures to specialize FEM models to obtain quantitative and qualitative results for systems such as body, chassis, and suspension components, as well as validation of the models by experimental data.

For many years durability tests engineers have worked in the sense of improving the tests that, at first, were performed using public roads with high time consumption and low reproducibility. Proving grounds were specially designed to reproduce the most important efforts to the body and chassis systems, but time problem was still there. Time and cost reduction allied to the needs of quality, reliability and reproducibility improvement led the engineers to develop methods and equipments to reproduce the durability tests in the lab. In this way the road simulators appear as a powerful tool able to perform durability tests with high reliability, self-controlled and with very low time compared to the road tests. At this scenery bench tests were also created to components and systems mainly used to anticipate problems before a whole vehicle test.

Driven by the necessity to reduce costs and improve products quality the automotive industry replaced the design method known as "trial and error" by those grounded on mathematical and physical theory. In this context, a longitudinal performance test was made by BAJA SAE UFMG team, in order to acquire vehicular performance data that will be used to validate computer models. The methodology consists of sensors and data acquisition system research, validation, fixation and installation in the vehicle, test and process of acquired data. From these steps, correlated data were acquired from magnitudes such as angular velocity in transmission shafts, global longitudinal acceleration and velocity, travel of break and throttle pedals and pressure inside of master cylinder. These results developed the knowledge about vehicular dynamic allowing the improvement of futures prototypes.

The accuracy of computer-based ground vehicle durability and ride quality simulations depends on accurate representation of road surface topology as vehicle excitation data since most of the excitation exerted on a vehicle as it traverses terrain is provided by the terrain topology. It is currently not efficient to obtain accurate terrain profile data of sufficient length to simulate the vehicle being driven over long distances. Hence, durability and ride quality evaluations of a vehicle depend mostly on data collected from physical tests. Such tests are both time consuming and expensive, and can only be performed near the end of a vehicle's design cycle. This paper covers the development of a methodology to synthesize terrain profile data based on the statistical analysis of physically measured terrain profile data.

The Hybrid Electric Vehicle Team of Virginia Tech (HEVT) is currently developing a control strategy for a parallel plug-in hybrid electric vehicle (PHEV). The hybrid powertrain is being implemented in a 2016 Chevrolet Camaro for the EcoCAR 3 competition. Fuzzy rule sets determine the torque split between the motor and the engine using the accelerator pedal position, vehicle speed and state of charge (SOC) as the input variables. The torque producing components are a 280 kW V8 L83 engine with active fuel management (AFM) and a post-transmission (P3) 100 kW custom motor. The vehicle operates in charge depleting (CD) and charge sustaining (CS) modes. In CD mode, the model drives as an electric vehicle (EV) and depletes the battery pack till a lower state of charge threshold is reached. Then CS operation begins, and driver demand is supplied by the engine operating in V8 or AFM modes with supplemental or loading torque from the P3 motor.

The Hybrid Electric Vehicle Team of Virginia Tech (HEVT) is currently modeling and bench testing powertrain components for a parallel plug-in hybrid electric vehicle (PHEV). The custom powertrain is being implemented in a 2016 Chevrolet Camaro for the EcoCAR 3 competition. The engine, a General Motors (GM) L83 5.3L V8 with Active Fuel Management (AFM) from a 2014 Silverado, is of particular importance for vehicle integration and functionality. The engine is one of two torque producing components in the powertrain. AFM allows the engine to deactivate four of the eight cylinders which is essential to meet competition goals to reduce petroleum energy use and greenhouse gas emissions. In-vehicle testing is performed with a 2014 Silverado on a closed course to understand the criteria to activate AFM. Parameters required for AFM activation are monitored by recording vehicle CAN bus traffic.

Faults in the intake and exhaust path of turbocharged common-rail Diesel engines can lead to an increase of emissions and performance losses. Standard fault detection strategies based on plausibility checks and trend checking of sensor data are not able to detect and isolate all faults appearing in the intake and exhaust path without employing additional sensors. By applying model based methods a limited sensor configuration can be used for fault detection. Therefore a model based fault diagnosis concept with parity equations is considered, [1]. In this contribution the fault diagnosis system, which comprises semi-physical thermodynamic turbocharger model, models of gas pressure in the intake and exhaust manifold, residual generation, residual to symptom transformation and fault diagnosis is presented.

Aiming the decrease of manufacturing costs, the automotive industry uses Computational Aided Engineering (CAE) and prototype testing for product development. In the field of simulation CAE could be performed using FEA (finite element analysis) or CFD (Computational Fluid Dynamic), the last one is the analysis of systems involving fluid flow, heat transfer and associated phenomena such as chemical reactions by means of computer-based simulation. One of the most important components of cooling system is a water pump which is evaluated through the fluid dynamic analysis. Therefore, this work aims to analyze the fluid flow inside an automotive water pump considering a three-dimensional steady-state using CFD, but also developing a methodology to evaluate it. The parameters of the analysis and the volumetric mesh were according to the simulated results approached the experimental results.

An experimental method for nondestructive estimation of damage in joints due to high mileage degradation in cars is presented. The method estimates damage by comparing transfer functions of the same car at zero and at high mileage. The potential of the method is demonstrated analytically using a three dimensional concept Finite Element Model (FEM) of a car body to simulate the transfer functions of this car body at zero and at high mileage. The results demonstrate that the method is effective for identifying the damaged joints as well as the relative degree of degradation.

A vehicle's response is predominately defined by the tire characteristics as they constitute the only contact between the vehicle and the road; and the surface friction condition is the primary attribute that determines these characteristics. The friction coefficient is not directly measurable through any sensor attachments in production-line vehicles. Therefore, current chassis control systems make use of various estimation methods to approximate a value. However a significant challenge is that these schemes require a certain level of perturbation (i.e. excitation by means of braking or traction) from the initial conditions to converge to the expected values; which might not be the case all the time during a regular drive.

This paper presents a novel infrastructural traffic monitoring approach that estimates traffic information by combining two sensing techniques. The traffic information can be obtained from the presented approach includes passing vehicle counts, corresponding speed estimation and vehicle classification based on size. This approach uses measurement from an array of Lidars and video frames from a camera and derives traffic information using two techniques. The first technique detects passing vehicles by using Lidars to constantly measure the distance from laser transmitter to the target road surface. When a vehicle or other objects pass by, the measurement of the distance to road surface reduces in each targeting spot, and triggers detection event. The second technique utilizes video frames from camera and performs background subtraction algorithm in each selected Region of Interest (ROI), which also triggers detection when vehicle travels through each ROI.

A new and unique electric vehicle powertrain model based on bidirectional power flow for propel and regenerative brake power capture is developed and applied to production battery electric vehicles. The model is based on a Willans line model to relate power input from the battery and power output to tractive effort, with one set of parameters (marginal efficiency and an offset loss) for the bidirectional power flow through the powertrain. An electric accessory load is included for the propel, brake and idle phases of vehicle operation. In addition, regenerative brake energy capture is limited with a regen fraction (where the balance goes to friction braking), a power limit, and a low-speed cutoff limit. The purpose of the model is to predict energy consumption and range using only tractive effort based on EPA published road load and test mass (test car list data) and vehicle powertrain parameters derived from EPA reported unadjusted UDDS and HWFET energy consumption.