Search Results

In the analysis for durability or R&H performance with the full vehicle multibody models, the need for component flexibility is increasing along with demand for more precise full vehicle system. The component elastic deformations are usually expressed by modal superposition from component normal mode analysis with finite element model for reducing model size and simulation time. Although the simulation results of MBD analysis are more accurate according to increasing the number of flexible body and modes, the increasing of flexible components makes worse simulation time and convergence in MBD analysis. Especially, in the MBD analysis including a flexible upper body, in substitution for large number degree of freedom FE model such as trimmed body, it should take a few times longer than the case of rigid upper body This paper proposes the methods of reducing computational cost with adequate mode selections without the loss of simulation accuracy in the flexible MBD.

The assessment of the Transmission Loss (TL) of vehicle components at Low-Mid Frequencies generally raises difficulties associated to the physical mechanisms of the noise transmission through the automotive panel. As far as testing is concerned, it is common in the automotive industry to perform double room TL measurements of component baffled cut-outs, while numerical methods are rather applied when prototype or hardware variants are not available. Indeed, in the context of recent efforts for reduction of vehicle prototypes, the use of simulation is constantly challenged to deliver reliable means of decision during virtual design phase. While the Transfer matrix method is commonly and conveniently used at Mid-High frequencies for the calculation of a trimmed panel, the simulation of energy transfer at low frequencies must take into account modal interactions between the vehicle component and the acoustic environment.

It is known that SEA is a rapid and simple methodology for analyzing complex vibroacoustic systems. However, the SEA principle is not always valid and one has to be careful about the physical conditions at which the SEA principle is acceptable. In this study, the appropriate damping loss factor of the vehicle interior cavity is studied in the viewpoint of the modal overlap factor of the cavity and the decay per mean free path (DMFP) of the cavity. Virtual SEA tests are performed with an FE model combination, which is suggested by a previous study of Stelzer et al. for the simulation of the sound transmission loss (STL) of vehicle panel structure. The FE model combination is consisting of the body in white (BIW), an acoustical-excited hemisphere-shaped exterior cavity, and the interior cavity. It is found that the DMFP of the interior cavity is appropriate between 0.5 ~ 1 dB for applying SEA principle.

Commercial vehicle manufacturers face unique challenges for the development of vehicle electronics systems. For one, customers typically have unique requirements coupled with an expectation of high reliability. Vehicle electronics is often the enabler for customized features. Ensuring that the vehicle will perform as demanded and promised adds a degree of burden on the vehicle manufacturers. Furthermore, the verification and testing of a large number of unique electronic system configurations is very expensive and time-consuming. This paper will explore how Model-Based Design can be used to meet these challenges and provide a high degree of confidence for both the manufacturer and the customer that requirements have been met. It will discuss factors to consider to support configurability, approaches for defining a system architecture that facilitates reuse, and capabilities for modeling state-based systems.

Fuel sloshing noise is involved with flow motion inside fuel tanks as well as structural characteristics of vehicles. Therefore it is necessary to introduce Fluid-Structure Interaction (FSI) analysis to predict sloshing noise phenomena more accurately. Purposes of this paper are to verify the reliability of the FSI method and suggest new CAE analysis processes to predict fuel sloshing noise. The vibration of floor panels induced by sloshing impact is evaluated through FSI analysis. A series of tests is carried out to validate simulation results. The numerical optimization of parameters is also carried out to reduce computation time. In addition, effects of sloshing noise factors are discussed based on simulation and test results. Lastly, a method to predict fuel sloshing noise by exerting sloshing load on a vehicle is suggested.

The need to meet new regulatory requirements as well as customer expectations in terms of machine productivity, safety, maintenance and uptime, is driving a significant transformation from conventional hydraulic and mechanical systems to electro-hydraulic systems in the earth-moving and agricultural equipment industry. The ability to model and simulate such systems plays a key role in this transformation by allowing manufacturers to test whether the system meets requirements using virtual prototypes rather than physical prototypes. Modeling the electrical, electronic, mechanical, and hydraulic domains in the same modeling environment can significantly improve the product development process of such machines. This paper illustrates those benefits using the example of an electro-hydraulic implement system.

Passenger fatigue during long distance driving is greatly influenced by the comfort performance of the seat. Seat comfort performance is determined by the appropriate contour of the seat and the appropriate pad with sufficient thickness. The height of vehicle has been lowered to enhance car styling, and battery for electric vehicle applied to the underbody of the vehicle, reducing the package space of the seat in the vehicle. These external factors eventually lead to a reduced pad thickness of the seat cushion and compromise one of the important components in the seat cushion compartment, creating an uncomfortable cushioning problem when driving long distances. To improve the cushion composition of the seat within a limited package, air bladders are applied to the underside of the cushion pad. In addition, the function to support the buttocks using the air bladders of the lower cushion, similar to lumbar support for the back, was implemented to improve cushion comfort performance.

In this study, the preliminary validation method of the steering system is constructed and the objective is to satisfy the target performance in the conceptual design stage for minimizing the problems after the detailed design. The first consideration about steering system is how to extract the reliable steering effort for parking. The tire model commonly used in MBD(Multi-Body Dynamics) has limited ability to represent deformations under heavy loads. Therefore, it is necessary to study adequate tire model to simulate the behavior due to the large deformation and friction between the ground and the tire. The two approaches related with F tire model and mathematical model are used. The second is how to extract each link’s load in the conceptual design stage. Until now, each link’s load could be derived only by actual vehicle test, and a durability analysis was performed using only pre-settled RIG test conditions.

A sliding door is one of the car door systems, which is generally applied to the vans. Compared with swing doors, a sliding door gives comfort to the passengers when they get in or out the car. With an increasing number of the family-scale activities, there followed a huge demand on the vans, which caused growing interests in the convenience technology of the sliding door system. A typical sliding door system has negative effects on the vehicle interior package and the operating effort. Since the door should move backward without touching the car body, the trajectory of the center rail should be a curve. The curve-shaped center rail infiltrates not only the passenger shoulder room, but also the opening flange curve, which results in the interior package loss. Moreover, as the passenger pulls the door outside handle along the normal direction of the door outer skin, the curved rail causes the opening effort loss.

The windshield is an integral part of almost every modern passenger car. Combined with current developments in the automotive industry such as electrification and the integration of lightweight material systems, the reduction of interior noise caused by stochastic and transient wind excitation is deemed to be an increasing challenge for future NVH measures. Active control systems have proven to be a viable alternative compared to traditional passive NVH measures in different areas. However, for windshield actuation there are neither comparative studies nor actually established actuation concepts available to the automotive industry. This paper illustrates a comparative conceptual study on windshield actuation for the active control of wind noise in a passenger car. Making use of an experimental modal analysis of the windshield installed in a medium-sized vehicle, a reduced order numerical simulation model is derived.

Using Model-Based Design, engineers model complex systems and simulate them on their desktop environment for analysis and design purposes. Model-Based Design supports a wide variety of C/C++ code generation applications that include stand-alone simulation, rapid control prototyping, hardware-in-the-loop testing, and production or embedded code deployment. Many of these code generation scenarios impose different requirements on the generated code. Stand-alone simulations usually need to run fast, for parameter sweep or Monte Carlo studies, but do not need to execute in true hard real-time. Hardware-in-the-loop tests by definition use engine control unit (ECU) component hardware that requires a hard real-time execution environment to protect the physical devices. Code generated for production ECUs must satisfy hard real-time, efficiency, legacy code, and other requirements involving verification and validation efforts.

The increased adoption of electronic controls in off-highway machines increases the complexity of typical machine systems and stresses the traditional process used to develop these machines. To address this issue design engineers are turning from the traditional design methods to Model-Based Design. By using models in the early design stages, engineers can create executable specifications that enable them to immediately validate and verify specifications against the requirements. These models also allow the machine designer to evaluate the complex interactions between mechanics, hydraulics, electronics and other physical phenomena and thereby detect design errors earlier when the cost to fix them is less. This paper presents a model-based approach for developing off-highway equipment machine systems. A dynamic model of the machine and the electro-hydraulic implement and propulsion system is developed and used to verify the overall machine behavior.

The alternator provides power to vehicle electrical loads with the battery, and its maximum current depends on various factors such as electrical load, engine speed, thermal condition, and other variables. Above all, thermal effects make alternator simulations more complicated. For example statically similar conditions may show different results according to the temperature variation for each alternator operation. This paper proposes a two-stage statistically-based model structure which separates dynamic thermal effects from steady state performance. The method was validated by experiments and shows good predictive performance, suitable for use in test reduction.

The purpose of the study is to investigate the ergonomic issues for control types and menu design types of in-vehicle information system (IVIS). The results showed that 1) linear-type controls with linear-type menu design had better performance 2) rotary-type control with rotary-type menu design had good subjective preference score 3) the performance and subjective preference of IVIS interface were strongly influenced by the compatibility between control types and menu design types of IVIS 4) there was a tendency that the performance of IVIS tasks was better when the display was located at higher level on center fascia. The results can be applied to develop a new control and menu design of IVIS from ergonomic view points.

Numerous machine elements are operated in mixed lubrication regime where is governed by a combination of boundary and fluid film effects. The direct contact between two surfaces reduces a machines life by increasing local pressure. In order to estimate machine's life exactly, the effect of asperity contact should be considered in the lubrication model. In this study, new 3-dimensional partial elasto-hydrodynamic lubrication (PEHL) algorithm is developed. The algorithm contains the procedures to find out solid contact regions within the lubricated regime and to calculate both the pressure by fluid film and the contact pressure between the asperities of the solids. Using the algorithm, we conducted the PEHL analysis for the contact between the rotating shaft and the inside of pinion gear. To investigate the effect of surface topology two different surfaces with sinusoidal profile are used. Both film thickness and pressure are calculated successfully through the PEHL algorithm.

This paper mainly focuses on a lateral control law for pre-given path following which is developed by using the backstepping control design methodology. The position information of the vehicle is obtained by Real Time Kinematic DGPS, and the yaw rate and side-slip angle used in controller are estimated by Kalman estimator. To show the performance of the proposed controller under different speed and various path curvature conditions, the results are given through experiments which are executed on proving ground especially designed for high maneuvering test of which minimum radius of curvature is about 60 m.

Electrical system capacity determination for conventional vehicles can be expensive due to repetitive empirical vehicle-level testing. Electrical system modeling and simulation have been proposed to reduce the amount of physical testing necessary for component selection [1, 2]. To add value to electrical system component selection, the electrical system simulation models must regard the electrical system as a whole [1]. Electrical system simulations are heavily dependent on the battery sub-model, which is the most complex component to simulate. Methods for modeling the battery are typically unclear, difficult, time consuming, and expensive. A simple, fast, and effective equivalent circuit model structure for lead-acid batteries was implemented to facilitate the battery model part of the system model. The equivalent circuit model has been described in detail. Additionally, tools and processes for estimating the battery parameters from laboratory data were implemented.

This paper proposes a modeling technique which is able to not only reliably and easily represent the hysteretic characteristics but also analyze the dynamic stress of a taper leaf spring. The flexible multi-body dynamic model of the taper leaf spring is developed by interfacing the finite element model and computation model of the taper leaf spring. Rigid dummy parts are attached at the places where a finite element leaf model is in contact with an adjacent one in order to apply contact model. Friction is defined in the contact model to represent the hysteretic phenomenon of the taper leaf spring. The test of the taper leaf spring is conducted for the validation of the reliability of the flexible multi-body dynamic model of the taper leaf spring developed in this paper. The test is started at an unloaded state with the excitation amplitude of 1∼2mm/sec and frequency of 132mm. First, the simulation is conducted with the same condition as the test.

Model-Based Design has become a standard in the automotive industry. In addition to the well-documented advantages that come from modeling control algorithms, [1,2,3,4] modeling plants can lead to more robust designs. Plant modeling enables engineers to test a controller with multiple plant parameters, and to simulate nominal or ideal values. Modeling variable physical parameters provides a better representation of what can be expected in production. Monte Carlo analysis is a standard method of simulating variability that occurs in real physical parameters. Automotive companies use Monte Carlo testing to ensure high quality, robust designs. Due to time and resource constraints, engineers often examine only a limited number of key parameters rather than an entire set. This leaves the design vulnerable to problems caused by missing the full potential impact of parameters that were unvaried during testing.

Model-Based Design is increasingly prevalent in industrial sectors including aerospace and automotive, but lacking from college and university curricula. The need for students to be adept at the modeling of systems, their associated subsystems, and overall system controller as per the standard industry practice is the impetus for The MathWorks, Freescale, and MotoTron to partner with Rose-Hulman Institute of Technology to address the lack of students familiar with this industry standard practice. Rose-Hulman Institute of Technology has created the Model-Based-System Design Center with the express purpose of introducing the philosophy of Model-Based Design to the educational community. This paper describes the function of the Center and the teaching materials currently being generated.