Search Results

During metal forming processes such as rolling and forging, deformable manganese sulfide (MnS) inclusions become elongated. Such elongated MnS inclusions can have considerable adverse effects on mechanical properties, if the inclusions are not aligned with the loading direction. The objectives of this study were to evaluate and compare fatigue, monotonic tensile and CVN impact behavior of SAE 4140 steel with high (0.077% S), low (0.012% S) and ultra low (0.004% S) sulfur contents at two hardness levels (40 HRC and 50 HRC). The longitudinally oriented samples at 40 HRC, where MnS inclusions were oriented along the loading direction, did not exhibit any significant sensitivity of tensile or fatigue properties to the sulfur content. For the transversely oriented MnS inclusions, however, the monotonic tensile test results indicate very low ductility of the high sulfur material at both hardness levels, where specimens failed shortly after yielding.

The National Science Foundation recently sponsored a Workshop on Environmentally Benign Manufacturing (EBM) for the Transportation Industries. The objective of the workshop was to determine future directions of research in the EBM area and to construct a roadmap for development of future research programs. While research in the fields of Design for the Environment (DfE) and Life Cycle Analysis (LCA) have focused on the product and product life cycles, an additional focus is needed to find and develop processes with less environmental impact within the manufacturing environment. This workshop explored EBM issues with respect to the enterprise, the products, the processes and the materials.

A vehicle steering knuckle undergoes time-varying loadings during its service life. Fatigue behavior is, therefore, a key consideration in its design and performance evaluation. This research program aimed to assess fatigue life and compare fatigue performance of steering knuckles made from three materials of different manufacturing processes. These include forged steel, cast aluminum, and cast iron knuckles. In light of the high volume of forged steel vehicle components, the forging process was considered as base for investigation. Monotonic and strain-controlled fatigue tests of specimens machined from the three knuckles were conducted. Static as well as baseline cyclic deformation and fatigue properties were obtained and compared. In addition, a number of load-controlled fatigue component tests were conducted for the forged steel and cast aluminum knuckles. Finite element models of the steering knuckles were also analyzed to obtain stress distributions in each component.

An optimization study was performed on a steel forged connecting rod with a consideration for improvement in weight and production cost. Since the weight of the connecting rod has little influence on its total production cost, the cost and the weight were dealt with separately. Reduction in machining operations, achieved by change in material, was a significant factor in manufacturing cost reduction. Weight reduction was achieved by using an iterative procedure. Literature survey suggests cyclic loads comprised of static tensile and compressive loads are often used for design and optimization of connecting rods. However, in this study weight optimization is performed under a cyclic load comprising dynamic tensile load and static compressive load as the two extreme loads. Constraints of fatigue strength, static strength, buckling resistance and manufacturability were also imposed. The fatigue strength was the most significant factor in the optimization of the connecting rod.

The drive of Design for the Environment is to reduce the environmental impact of both design and manufacturing processes. The most frequent method recommended is to substitute better materials and processes. However, there are processes that will continue to have undesirable environmental impacts due to the lack of knowledge of better methods. These processes are critical to manufacturing of products and can not be eliminated. All possible substitutions appear to have worse impacts. This paper explores modeling these processes and imposing a control method which permits an improvement of the environmental impact.

Fatigue behavior of two types of automotive steel, quenched and tempered SUJ2 and carburized SCM820PRH, which are applied as powertrain parts are studied. These two types of steel are different in their hardness distribution from surface to core. The hardness of quenched and tempered SUJ2 is homogenous, in contrast to that of carburized SCM820PRH (SCM) which decreases from surface to core. These steels are investigated in terms of their monotonic tensile properties and fatigue behavior. A number of predictive methods were used to describe the fatigue behavior of these steels. A simple predictive method is based on approximation of S-N curve from ultimate tensile strength. The well-known Murakami’s defect area method was also applied for the prediction of the high cycle fatigue strength.

Fatigue is the primary cause of failure of crankshafts in internal combustion engines. The cyclic loading conditions and the stress concentrations in the crank pin fillets are unavoidable, and can result in fatigue failure. The objectives of this study were to compare the fatigue behavior of forged steel and ductile iron crankshafts from a one-cylinder engine as well as to determine if the fatigue life of a crankshaft can be accurately estimated using fatigue life predictions. Monotonic tensile tests as well as strain-controlled fatigue tests were conducted using specimens machined from the crankshafts to obtain the monotonic and cyclic deformation behavior and fatigue properties of the two materials. The forged steel had higher tensile strength and better fatigue performance than the ductile cast iron. Charpy v-notch impact tests were also conducted using specimens machined from the crankshafts to obtain and compare the impact toughness of the materials.