Search Results

This paper describes the development of a fracture finite element (FE) model for laser screw welding (LSW) and validation of the model with experimental results. LSW was developed and introduced to production vehicles by Toyota Motor Corporation in 2013. LSW offers superb advantages such as increased productivity and short pitch welding. Although the authors had previously developed fracture FE models for conventional resistance spot welding (RSW), a fracture model for LSW has not been developed. To develop this fracture model, many comprehensive experiments were conducted. The results revealed that LSW had twice as many variations in fracture modes compared to RSW. Moreover, fracture mode bifurcations were also found to result from differences in clearance between welded plates. In order to analyze LSW fracture phenomena, detailed FE models using fine hexahedral elements were developed.

The development of an alternative oxygen reduction electrocatalyst to platinum based electrocatalysts is critical for practical use of the polymer electrolyte membrane fuel cell (PEMFC). Transition metal sulfide chalcogenides have recently been reported as a possible candidate for Pt replacement. Our work focused on chalcogenides composed of ruthenium, molybdenum, and sulfur (RuMoS). We elucidate the factors affecting electrocatalytic activity of carbon supported RuXMoY SZ catalyst. This was demonstrated through a correlation of oxygen reduction reaction (ORR) activity of the catalysts with structural changes resulting from designed changes in sulfur composition in the catalysts.

This article proposes a rubber suspension bushing model considering amplitude dependence as a useful tool at the initial design phase. The purpose of this study is not to express physical phenomena accurately and in detail and to explore the truth academically, but to provide a useful design method for initial design phase. Experiments were carried out to verify several dynamic characteristics of rubber bushings under vibration up to a frequency of 100 Hz, which is an important frequency range when designing ride comfort performance. When dynamic characteristic theory and the geometrical properties of the force-displacement characteristic curve were considered using these dynamic characteristics as assumptions, an equation was derived that is capable of calculating the dynamic stiffness under an arbitrary amplitude by identifying only two general design parameters (dynamic stiffness and loss factor) under a reference amplitude.

Silver metallic colors with thin and smooth aluminum flake pigments have been introduced for luxury brand OEMs. Regarding the paint formulation for these types of colors, low non-volatile(NV) and high aluminum flake pigment contents are known as technology for high metallic appearance designs. However, there are two technical concerns. First is mottling which is caused by uneven distribution of the aluminum flake pigments in paint film and second is poor film property due to high aluminum pigment concentration in paint film. Therefore, current paint systems have limitation of paint design. As a countermeasure for those two concerns, we had investigated cellulose nanofiber (CNF) dispersion liquid as both the coating binder and rheology control agent in a new type of waterborne paint system. CNF is an effective rheology control agent because it has strong hydrogen bonds with other fiber surfaces in waterborne paint.

Hand dismantling of end of life vehicles (ELV) may have limited use on recovering the majority of materials that will be in our future automobiles. Research is being conducted on automated methods to recover pure plastics from automotive shredder residue (ASR). As part of USCAR initiative, the Vehicle Recycling Partnership (VRP), a cooperative effort among Chrysler, Ford and General Motors undertook a study to determine the feasibility of obtaining pure plastics from ASR using density and skin flotation separation technologies. The total project concept is described in this paper including important elements such as the detailed dismantling of a baseline vehicle to define total plastics complexity, shredding vehicles, collecting ASR samples and performing R&D work on automated recovery methodologies.

The purpose of this study was to analyze and quantify the effects of accelerated weathering on the surface of various “weatherable” polymers currently utilized for molded-in-color exterior automotive applications. Evaluations consisted of gloss/color retention and surface changes after accelerated weathering exposure, with and without intermittent washing, to simulate product life cycle. Results were found to be affected by both polymer type and interim surface treatments. Data are presented as a means to define specific performance and aesthetic capabilities of these various polymers in a mold-in-color environment to optimize material selection for related component applications.

1 The principal characteristics required of sealing materials used in the body shop have focused on their adhesion to oily steel sheets and quick curing performance. Means for attaining these characteristics have been narrowed down to a basic resin system and a curing system. Various techniques have been studied to ensure proper anti-corrosion performance at the sealer application boundaries and thin application areas. They include the addition of anti-corrosion fillers, the provision of conductivity (through electro-deposition), and the application of a micro foam film over the application boundaries. Thus, prospects for attaining the same level of anti-corrosion performance as existing materials have been achieved.

More than twenty years have passed since we invented polymer-clay nanocomposites (PCN), in which only a few wt.-% of silicate is randomly and homogeneously dispersed in the polymer matrix. When molded, these nanocomposites show superior properties compared to pristine polymers such as tensile strength, tensile modulus, heat distortion temperature, gas barrier property, and so on. The number of papers on PCN has increased rapidly in recent years, reaching over 500 only in 2005. As the pioneers of the new technology, we will review its history highlighting our works. Epoch-making events of PCN are as follows: In 1985, The first PCN, nylon 6-clay hybrid (NCH), was invented. In 1987, NCH was first presented at the ACS Fall Meetings. In 1989, NCH was presented at the MRS Fall Meetings, firing PCN. In 1989, Toyota launched cars equipped with a NCH part. In 1996, Clay was found to cause a memory effect in liquid crystals.

This paper describes development of a numerical simulation method for the FMVSS 201 testing. This method considers not only deformation but also fracture of plastic materials. a simplified calculation method for predicting the load during impact of absorbing plastic materials was introduced from the numerical simulation results. By applying this simplified calculator method trial and error in development would be reduced.

This study was conducted to analyze and quantify the effects of accelerated weathering on the surface of various “weatherable” polymers currently utilized for molded-in-color exterior automotive applications. Evaluations consisted of gloss/color retention and surface changes after accelerated weathering exposure, with and without intermittent washing, to simulate product life cycle. Results were found to be affected by both polymer type and interim surface treatments. Data are presented as a means to define specific performance and aesthetic capabilities of these various polymers in a mold-in-color environment to optimize material selection for related component applications.

Through a polymer design and precise morphology control, The Super Olefin Polymer, TSOP-1 and TSOP-5 were developed for the material consolidation of interior and exterior parts, respectively. Due to a good balance of TSOP performance, several conventional materials were consolidated into one material for each application. Accordingly, considerable amounts of weight reduction and cost savings have been obtained. In addition to the excellent recyclability of TSOP, the coated bumpers collected from the market were re-utilized through paint decomposition technology. The first dashboard construction, molded partially with foam-padded skin, was also realized. The current amount of TSOP used in a vehicle is about 30% of the total amount of plastic materials. Through the usage of TSOP, 70% of the material consolidation has been achieved.

We studied the use of Bio-plastics (plastics made from plants) such as poly(lactic acid) (PLA) to automotive parts. To apply this material to automotive plastic parts, improvement in heat and impact performance is required. From the viewpoint of suppressing the increase in CO2 emissions, we attempted to improve the performance of PLA by combining with natural fiber. As the result, we could improve both heat and impact performance. In addition, we could achieve higher modulus and lower bulk density, which leads to the weight reduction of automotive parts.

We studied the application of Bio-plastics (plastics made from plants) such as poly(lactic acid) (PLA) to automotive parts. To apply this material to automotive plastic parts, major improvement is required for thermal and impact performance. From the viewpoint of suppressing the increase CO2 emissions, we attempt to improve the performance of PLA by combining with natural fiber. As the result, we could improve both thermal and impact performance. In addition, we could achieve higher modulus and lower bulk density, which lead to the weight reduction of automotive parts.

A new material recycling technology for crosslinked rubber was developed using the continuous reactive processing method. In this process of producing reclaimed rubber, breakage of crosslinking points in the crosslinked rubber occurs selectively under the controls of shear stress, reaction temperature, and internal pressure in a modular screw type reactor. Deodorization during the process has also become possible by a newly developed method. The reclaimed rubber obtained from rubber waste generated from both automobile manufacturing products and post-consumer products shows excellent mechanical properties applicable to new rubber compounds. Furthermore, an enhanced rubber recycling process for producing thermoplastic elastomer (TPE) based on rubber waste has been established. The obtained TPE exhibits highly recoverable rubber elasticity and mechanical properties comparable to commercial TPE.

Toyota is implementing various technical developments in various fields for protection of environment. Reducing the fuel consumption is a matter of great urgency for the reduction of CO2 emissions. In the technology of vehicle body development, mass reduction and the improvement of aerodynamics are mainly important for fuel economy. As the one of way for this, we adopted resin glass as the back door glass of ES3, small-sized low-fuel consumption vehicle. (Figure 1,2,3) The first advantage of resin glass is the low density that weights about a half of inorganic glass. However resin glass is needed higher thickness for equivalent rigidity, as the result approximately 41% mass reduction was achieved. However resin glass is relatively expensive. Therefore it seems to be difficult to expand the usage of resin for this application. Then, we focused on additional advantage of resin glass, in order to make good use of resin glass. The second advantage of resin glass is design flexibility.

From the viewpoint of measures for environmental issues, the amount of solvents in paint for aluminum wheels needs to be minimized. Environmentally friendly powder coatings have been used widely for primer coating and clear coating, but there is no precedent for its use for base coating. This time, we optimized the condition of surface treatment of pigment and hardening behavior of constituent resin in the melting process and succeeded in developing a metallic powder coating for aluminum wheels that fulfills the appearance and the quality requirements of aluminum wheels.

Underbody coating is used to prevent chipping damage of the automobile underbody and wheel well. Multi-functional material that gives sound insulating properties is called sound insulating underbody coating. This paper describes the development of underbody coating material with powdered acrylic composition as an alternative to polyvinyl chloride resin. The new material also has better foaming properties. It is possible to ensure excellent sound insulating performance with thin film. This multi-functional underbody coating is the first application in the world with weight reduction and cost saving, and in a more environmentally acceptable manner.

Thermoplastic polyurethane (TPU) Powder Slush material for automotive interior parts, like instrument panels and door trim was developed as an alternative material for polyvinyl chloride (PVC) Powder Slush. Generally, TPU has poor anti-alcohol performance. However this performance has to be improved for automotive interior parts because the common cleaner solvent for interior parts usually contains some type of alcohol. Through our study of various TPU formulas, sufficient anti-alcohol performance was achieved by introducing aromatic polyol. Due to negative effects of aromatic polyol for low temperature and melting properties, additional study for plasticizer was essential. These properties are important for air bag deployment performance and moldability of powder slush. In order to solve these problems, various types and amounts of plasticizer were studied. Benzoic ester produced the best balance between compatibility with urethane polymer and anti-fogging performance.

We studied the adoption of plastics derived from plants (bioplastics) such as poly(lactic acid) (PLA) for automotive parts in order to contribute to suppressing the increase in CO, emissions. For this application. major improvements of heat and impact resistance are needed. As a method to improve heat resistance, we developed PLA combined with clay of high heat resistance. As a result. we succeeded in synthesizing a PLA-clay nanocomposite using 18(OH)2-Mont. In-mold crystallization of PLA-clay nanocomposite lead to the great suppression of storage modulus decrease at high temperature. which in turn improved the heat resistance of PLA.

The renewed platform of the upcoming flagship front-engine, rear-wheel drive (FR) vehicles demands high levels of driving performance, fuel efficiency and noise-vibration performance. The newly developed driveline system must balance these conflicting performance attributes by adopting new technologies. This article focuses on several technologies that were needed in order to meet the demand for noise-vibration performance and fuel efficiency. For noise-vibration performance, this article will focus on propeller shaft low frequency noise (booming noise). This noise level is determined by the propeller shaft’s excitation force and the sensitivity of differential mounting system. In regards to the propeller shaft’s excitation force, the contribution of the axial excitation force was clarified. This excitation force was decreased by adopting a double offset joint (DOJ) as the propeller shaft’s second joint and low stiffness rubber couplings as the first and third joints.