Search Results

A new wind tunnel was developed and adopted by Toyota Motor Corporation in March 2013. This wind tunnel is equipped with a 5-belt rolling road system with a platform balance that enables the flow simulation under the floor and around the tires in on-road conditions. It also minimizes the characteristic pulsation that occurs in wind tunnels to enable the evaluation of unsteady aerodynamic performance aspects. This paper describes the technology developed for this new wind tunnel and its performance verification results. In addition, after verifying the stand-alone performance of the wind tunnel, a vehicle was placed in the tunnel to verify the utility of the wind tunnel performance. Tests simulated flow fields around the vehicle in on-road conditions and confirmed that the wind tunnel is capable of evaluating unsteady flows.

It is well understood that using lower viscosity engine oils can greatly improve fuel economy [1, 2, 3, 4]. However, it has been impossible to evaluate ultra-low viscosity engine oils (SAE 0W-12 and below) utilizing existing fuel economy test methods. As such, there is no specification for ultra-low viscosity gasoline engine oils [5]. We therefore developed firing and motored fuel economy test methods for ultra-low viscosity oils using engines from Japanese automakers [6, 7, 8]. This was done under the auspices of the JASO Next Generation Engine Oil Task Force (“TF” below), which consists mainly of Japanese automakers and entities working in the petroleum industry. Moreover, the TF used these test methods to develop the JASO GLV-1 specification for next-generation ultra-low viscosity automotive gasoline engine oils such as SAE 0W-8 and 0W-12. In developing the JASO GLV-1 specification, Japanese fuel economy tests and the ILSAC engine tests for evaluating engine reliability were used.

This paper provides an overview of automotive electronic systems put into products over the past decade, and describes automotive electronics which have been demonstrated in experimental cars. In addition, future electronic systems found to be promising for the practical use in coming years and the direction of development of electronics are also discussed, as an extention of the overview mentioned above.

A communication system that uses roadside beacons to broadcast road and traffic information and private messages to vehicles has been developed. The system, called Road/Automobile Communication System (RACS), was the result of a joint research project involving the Public Works Research Institute and 25 private-sector corporations. This paper contains an outline of RACS and of an onboard system developed by TOYOTA and presents the results of field tests conducted in the Tokyo area. The results not only verify the capability of the RACS system and the effectiveness of the in-vehicle equipment but also indicate the potential of such a beacon based network to improve traffic jam and driving safety whilst providing enhanced communication facilities without increasing radio-wave congestion.

This paper describes the Electro-Multivision map navigation software mounted in the Toyota Soarer (1991). The following functions are required of on-board map navigation software: 1. Indication of the exact position of the vehicle to the driver 2. Determination of the optimum path to the destination and presentation of this route to the driver in the simplest way 3. Accommodation of a wide variety of destinations and settings for different users The following gives some examples of how these functions are achieved and outlines the associated technologies. 1. Path finding and associated display technology Path finding algorithm and technology for displaying the calculated on the map; construction of a data base on CD-ROM 2. Technology for determination of the current position utilizing map matching and the global positioning system(GPS) A method with improved reliability based on two current position outputs obtained using map matching and the GPS and the mutual compensation method 3.

The stability of Diesel/Biodiesel blends can play an important role in deposits formation inside the fuel injection system (FIS). The impact of the stability of FAME/Diesel fuel blends on lacquer deposits formation and on the behavior and reliability of the FIS was investigated using blends of Rapeseed and Soybean methyl esters (RME, SME) and conventional Diesel fuel (volume fractions of RME and SME range from 0 to 20%v/v). Fuels were aged under accelerated conditions and tested on an injection test rig according to an operating cycle developed to provoke injector needle blocking. The soaking duration was found to affect injector fouling. A relationship between the injector fouling tendency and the fuel stability was established. Under current test condition, injectors fouling increased with fuel oxidation measured with Total-Acid-Number.

In order to investigate the effect of sulfur and distillation properties on exhaust emissions, emission tests were carried out using a California Low Emission Vehicle (LEV) in accordance with the 1975 Federal Test Procedure ('75 FTP). To study the fuel effect on the exhaust emissions from different systems, these test results were compared with the results obtained from our previous studies using a 92MY vehicle for California Tier 1 standards and a 94MY vehicle for California TLEV standards. (1)(2) First, the sulfur effect on three regulated exhaust emissions (HC, CO and NOx) was studied. As fuel sulfur was changed from 30 to 300 ppm, the exhaust emissions from the LEV increased about 20% in NMHC, 17% in CO and 46% in NOx. To investigate the recovery of the sulfur effect, the test fuel was changed to 30 ppm sulfur after the 300 ppm sulfur tests. The emission level did not recover to that of the initial 30 ppm sulfur during three repeats of the FTP.

Detergent additives in automotive gasoline fuel are mainly designed to reduce deposit formation on intake valves and fuel injectors, but it has been reported that some additives may contribute to CCD formation. Therefore, a standardized bench engine test method for CCDs needs to be developed in response to industry demands. Cooperative research between the Petroleum Association of Japan (PAJ) and the Japan Automobile Manufacturers Association, Inc. (JAMA), has led to the development of a 2.2L Honda engine dynamometer-based CCD test procedure to evaluate CCDs from fuel additives. Ten automobile manufacturers, nine petroleum companies and the Petroleum Energy Center joined the project, which underwent PAJ-JAMA round robin testing. This paper describes the CCD test development activities, which include the selection of an engine and the determination of the optimum test conditions and other test criteria.

A new test machine has been developed which can evaluate vibration due to stick-slip using an actual full-scale clutch pack. Using this machine, a static breakaway friction coefficient measurement test method and a stick-slip test method have been established. Both methods have been shown to provide results which correlate with the results from both a full-scale assembly test and a vehicle shudder evaluation test. The evaluation of the frictional properties of commercial oils using these test methods showed that the static breakaway friction coefficient and the stick-slip properties have generally contradictory performance to each other for automatic transmission. The study of the frictional properties for typical additives and an analysis of the surface of the steel plates with ESCA (Electron Spectroscopy for Chemical Analysis) showed that the frictional properties are significantly affected by the additives adsorbed on the clutch plate sliding surface.

Recently in the world, many modifications and improvements have been taking place in automatic transmission fluid (ATF) in order to get more excellent performance and durability of automatic transmission. The most important criterion for the improvement of ATF is a superior friction characteristic. To consider the performance of ATF, we have investigated the correlation of criteria between actual vehicle tests and bench-scale tests (e.g. SAE#2 Friction Test). And it was proved that conventional criteria and test methods for bench-scale tests were not enough to give best prediction of actual vehicle performance especially for shift quality, anti-shudder performance and static torque capacity which were regarded as of major importance for the development. Based on the findings, we have considered new criteria and test methods for the frictional characteristics, and specific requirements for ATF have been proposed from the standpoint of actual vehicle performance.

Vehicle body movements that occur during cornering have a strong influence on the evaluation of ride and handling. As a first step, we analyze subjective comments from trained drivers and find that the sense of vision played a major part in cornering feel. As a result of quantitative evaluations, we hypothesize that smaller time lag between roll angle and pitch angle made cornering feel better. We perform a human sensitivity evaluation, which confirmed this hypothesis. Given this result, we derive analytical equations for the roll center kinematics and the damping characteristics, in order to find a theoretical condition for the time lag of 0sec (giving a good cornering feel). We verify this by experiment.

Toyota has developed a new sports shift control system introduced in the world's first eight-speed automatic transmission (AA80E), which is implemented in the “LS 460” and has been adopted in the “IS F” (upcoming 2008 model). This enables the IS F to be a vehicle that also permits the enjoyment of driving on circuits as well as achieving that “fun-to-drive” image. In sports driving, as achieved by the conventional torque converter-type automatic transmissions, shift response performance for shift operation and linearity performance for accelerator operations were challenges to tackle. On the contrary, the newly developed sports shift control system has resolved these challenges and enables the IS F to be capable of responding to a driver's intention quickly and accurately, letting the driver truly experience satisfaction.

Grip feeling is an important facet in vehicle dynamics evaluation from a driver satisfaction and enjoyment standpoint. To improve grip feeling, we analyzed the subjective comments from test driver's about grip feeling and an evaluated human sensitivity to lateral motion. As a result, we found that drivers evaluate transient grip feeling according to the magnitude of lateral jerk. Next, we analyzed what vehicle parameters affect lateral jerk by using theoretical equations. As a result, we found that cornering power is an important parameter, especially the cornering power of rear tires as they can be create larger lateral jerk than can front tires.

A full vehicle multi-body dynamic (MBD) model with suspension control system is developed for fatigue life prediction under rough road condition. The model consists of tires, a trimmed body, heavy attached parts, powertrain, suspension, joints, and a driver model, and includes a suspension control system that varies characteristics of the suspension according to the rough road inputs. For tires, a commercial MBD tire model is employed with identifiable parameters. The models are simulated to run on the optically measured road surface of the proving ground. Apart from the trimmed body, several important heavy attached parts are modeled separately, that represent dynamic behavior that induces complex body input load. These parts, along with suspension and powertrain systems are connected to the body using nonlinear elements such as joints, springs, and dampers. Contact conditions are used to represent mount bushing, hood lock, stopper rubber, etc.

Technologies of 4WD chassis dynamometers (CHDY hereinafter) have advanced dramatically over the past several years, enabling 4WD vehicles to be tested without modifying their drive-train into 2WD. These advances have opened the use of 4WD-CHDY in all fuel economy and emission evaluation tests. In this paper, factors that influence the accuracy of fuel economy tests on 4WD CHDY are discussed. Fuel economy tests were conducted on 4WD CHDY and we found that most of the vehicle mechanical loss is the tire loss and that stabilizing the tire loss of the test vehicle is essential for the test reproducibility.

We have developed a New Black-face Cluster with Transparent EL Display, positioned on the speedometer, to display driver support information within the cluster; mass production of this DUAL VISION CLUSTER commenced in September 1999. The following were two requirements for implementing this cluster. 1) Selection of display device 2) Positioning of cluster in front of speedometer, using Transparent EL Display In this session, we will explain how we resolved the issues involved in development of this new Black-face Cluster. We will also describe the structure of the cluster.

In the field of automotive gasoline engines, new products aiming at greater fuel economy and cleaner exhaust gases are under development with the aim of preventing environmental destruction. Severe ignition environments such as lean combustion, stronger charge motion, and large quantities of EGR require ever greater combustion stability. In an effort to meet these requirements, an iridium plug has been developed that achieves high ignitability and long service life through reduction of its diameter, using a highly wear-resistant iridium alloy as the center electrode.(1)(2) Recently, direct injection engines have attracted attention. In stratified combustion, a feature of the direct injection engine, the introduction of rich air-fuel mixtures in the vicinity of the plug ignition region tends to cause carbon fouling. This necessitates plug carbon fouling resistance.

A highly reliable all-mechanical air bag system has been developed with a production cost lower than the electrical air bag system. All components, such as the bag, inflator and sensor are integrated into the steering wheel. Regarding the sensor design, we first discussed the requirements of the sensor to optimize the driver's protection, and then we designed it using a simulation method. We have confirmed by crash tests that this method is correct, and have found that this system is effective for reducing facial injuries.

A description is made of new control methods to improve response of wheel slip regulation. These methods enabled a new Traction Control (TRC) system based on throttle control rather than brake pressure to be developed. Major points are as follows: (1) Use of fuel injection cut-off to minimize delay (2) Additional adaptive throttle control logic By these means, a response nearly equal to that with brake pressure control is achieved at lower cost and with a considerable weight saving. Furthermore, the system, by suppressing noise and vibration, enhances the driver's control ability.

Instrument clusters used in automobiles play an important role as man-machine interface. A variety of information about the current driving situation is conveyed to the driver quickly and accurately. A great interest has been taken in the high visibility and legibility of the head-up display (subsequently abbreviated as HUD). Originally developed as display used in aeronautical applications, we have tried to exploit ways to adapt this device for automotive use. We have succeeded to produce a new HUD system, which has the following design features; (1) High brightness and high contrast display device using a liquid crystal display (subsequently abbreviated as LCD) and a halogen lamp illumination. (2) Long focus display in two colors using holographic lens. (3) Automatic dimming control system using an illuminance sensor. (see Fig. 1)