Search Results

Low Speed Pre-Ignition (LSPI), also referred to as Stochastic Pre-Ignition (SPI), Superknock or Megaknock is an undesirable combustion phenomenon that limits the fuel economy, drivability, emissions and durability performance of modern turbocharged gasoline engines. Numerous studies have previously reported that the frequency of LSPI is sensitive to engine oil composition. One of these drivers is the concentration of Calcium, which is usually delivered in the form of a detergent in the additive package. Switching to completely all-Magnesium detergent and/or severely limiting the concentration of Ca in the engine oil have recently been proposed as potential means to reduce LSPI. In this work, we evaluate the impact of detergent type on LSPI performance as well as on other performance that the modern engine oil needs to deliver. Particularly the impact of detergent type on Fuel Economy performance is evaluated.

Traffic congestions are increasingly severe in urban areas, especially at the merging areas of the ramps and the arterial roads. Because of the complex conflict relationship of the vehicles in ramps and arterial roads in terms of time-spatial constraints, it is challenging to coordinate the motion of these vehicles, which may easily cause congestions at the merging areas. The connected and automated vehicles (CAVs) provides potential opportunities to solve this problem. A centralized merging control method for CAVs is proposed in this paper, which can organize the traffic movements in merging areas efficiently and safely. In this method, the merging control model is built to formulate the vehicle coordination problem in merging areas, which is then transformed to the discrete nonlinear optimization form. A simulation model is built to verify the proposed method.

Recent pressures on vehicle manufacturers to reduce their average fleet levels of CO2 emissions have resulted in an increased drive to improve fuel economy and enable use of fuels developed from renewable sources that can achieve a net reduction in the CO2 output of each vehicle. The most popular choice for spark-ignition engines has been the blending of ethanol with gasoline, where the ethanol is derived either from agricultural or cellulosic sources such as sugar cane, corn or decomposed plant matter. However, other fuels, such as butanol, have also arisen as potential candidates due to their similarities to gasoline, e.g. higher energy density than ethanol. To extract the maximum benefits from these new fuels through optimized engine design and calibration, an understanding of the behaviour of these fuels in modern engines is necessary.

The traditional vehicle-based approach to measuring the effect of oil-related fuel economy has relied on separate oil-aging and measurement processes where oil-aging takes place using an established driving protocol like the EPA Approved Mileage Accumulation (AMA) Driving Schedule for vehicle aging, then at set mileage intervals fuel economy is assessed using procedures such as the EPA FTP75 and Highway Fuel Economy emission test protocols described in 40 CFR, Parts 86 and 600. These test methods are useful for producing discrete snapshots of fuel economy at set mileage intervals but are unable to provide continuous information about oil-related changes in fuel economy. During the tests, the vehicle's fuel economy is indirectly calculated using a carbon-balance method of the bagged sample of dilute tailpipe emissions that effectively integrates the fuel economy of the vehicle during the sample interval which varies between eight and fifteen minutes.

A host of bench and engine tests have historically been used by formulators to assess fuel economy when developing engine oils for gasoline-powered passenger cars and light trucks. Some of these methods assess basic lubricant physical properties such as hydrodynamic, boundary and thin-film friction, and are useful for quickly screening experimental components and formulations. Some methods assess rotational drag of a motored engine and offer insights into the friction of various engine parts. Still other methods directly measure the energy consumption in a test engine running in a research laboratory and thus come the closest to simulating a consumer-operated vehicle. Each test method has inherent limitations and is based on underlying assumptions, producing artifacts that must first be understood and then analyzed for relevance to either industry lubricant specifications or real world fuel economy performance.

An energy management strategy is needed to optimally allocate the driver's power demands to different power sources in the fuel cell hybrid vehicles. The driver's power demand is modelled as a Markov process in which the transition probabilities are estimated on the basis of the observed sample paths. The Markov Decision Process (MDP) theory is applied to design a stochastic energy management strategy for fuel cell hybrid vehicles. This obtained control strategy was then tested on a real time simulation platform of the fuel cell hybrid vehicles. In comparison to the other 3 strategies, the constant bus voltage strategy, the static optimization strategy and the dynamic programming strategy, simulations in the Beijing bus driving cycle demonstrate that the obtained stochastic energy management strategy can achieve better performance in fuel economy in the same demand of dynamic.

The effect on the intake flow field, air fuel mixing processes, thermodynamic performance and emissions output has been investigated for a range of valve operating profiles. A standard speed load point of 2000 rpm and 2.7 bar IMEP720° has been reached by throttling the intake whilst running standard cam profiles, by early closing of both inlet valves (EIVC) and by early closing of each inlet individually to generate bulk swirl motions within the cylinder. Data has been recorded at stoichiometric air fuel ratios for both direct injection and port fuelled operation. The valve profiles have been applied to two single cylinder homogeneous gasoline direct injection (GDI) spark ignition engines, developed to investigate the potential of controlling engine load by limiting the inducted air mass using fully variable valve timing (FVVT) to reduce pumping losses at part load.

For a spark-ignition engine, the parasitic loss suffered as a result of conventional throttling has long been recognised as a major reason for poor part-load fuel efficiency. While lean, stratified charge, operation addresses this issue, exhaust gas aftertreatment is more challenging compared with homogeneous operation and three-way catalyst after-treatment. This paper adopts a different approach: homogeneous charge direct injection (DI) operation with variable valve actuations which reduce throttling losses. In particular, low-lift and early inlet valve closing (EIVC) strategies are investigated. Results from a thermodynamic single cylinder engine are presented that quantify the effect of two low-lift camshafts and one standard high-lift camshaft operating EIVC strategies at four engine running conditions; both, two- and single-inlet valve operation were investigated. Tests were conducted for both port and DI fuelling, under stoichiometric conditions.

This experimental work was concerned with the combination of internal EGR with an early inlet valve closure strategy for improved part-load fuel economy. The experiments were performed in a new spark-ignited thermodynamic single cylinder research engine, equipped with a mechanical fully variable valvetrain on both the inlet and exhaust. During unthrottled operation at constant engine speed and load, increasing the mass of trapped residual allowed increased valve duration and lift to be used. In turn, this enabled further small improvements in gas exchange efficiency, thermal efficiency and hence indicated fuel consumption. Such effects were quantified under both port and homogeneous central direct fuel injection conditions. Shrouding of the inlet ports as a potential method to increase in-cylinder gas velocities has also been considered.

The traditional vacuum booster is gradually replaced by Brake-by-Wire system (BBW) in modern passenger car, especially Electric Vehicle (EV). Some mechanical and hydraulic components are replaced by electronic components in Brake-by-Wire system. Using BBW system in modern passenger vehicles can not only improve the automotive safety performance, reliability and stability, but also promote vehicle maneuverability, comfort, fuel economy and environmental protection. Although vehicle's braking performance is greatly improved by using BBW, the system will inevitably consume some energy of the vehicle power supply, thus introducing unexpected drawback in comparison with the traditional vacuum assist braking system, since it doesn't need any electric power. Therefore, the analysis of energy consumption on typical main cylinder booster based BBW system under typical driving cycles will contribute to advanced design of current advanced braking system.

Good shift quality in automatic transmissions is important for fuel efficiency, driver comfort, and performance. Maintaining this performance over the life of the vehicle is also important. Typically lubricant development focuses on reducing viscosity and friction in order to reduce parasitic losses. In an automatic transmission other factors are also important for good performance, primarily due to the shifting clutches and the torque converter clutch. A high level of friction is desirable for torque capacity and a steady decrease in friction as sliding speed (rpm) decreases is necessary for both good shift feel and good friction system durability over the lifetime of the vehicle. Changes in the friction system over time that result in a lowering of the friction level, particularly at higher sliding speeds, compromise the performance of both types of clutches.

Gasoline direct injection (GDI) engines have been developed rapidly in recent years, driven by stringent legislative requirements on vehicle fuel efficiency and emissions. However, one challenge facing GDI is the formation of particulate emissions, particularly with the presence of injector tip deposits. The Chinese market features some gasoline fuels that contain no detergent additives and are prone to deposit formation, which can affect engine performance and emissions. The use of detergent additives to mitigate the formation of injector deposits in a GDI engine was investigated in this study by testing a 1.5L turbocharged GDI engine available in the Chinese market. The engine was operated both on base gasoline and on gasoline dosed with detergent additives to evaluate the effect on injector deposit formation and engine performance and emissions.

Due to its simplicity and fuel economy benefit, continuously variable transmission (CVT) technology has gained a lot of attention in recent years. Market penetration of CVT technology is increasing rapidly compared to step-type automatic transmission technology. OEMs, Tier 1 suppliers, and lubricant suppliers are working to further improve the fuel economy benefit of CVTs. As a lubricant supplier, we want to understand the effects of fluid properties on CVT fuel economy (FE). We have formulated fluids that had KV100 ranges from 2-4 cSt to 7-9 cSt with various types and viscosities of base oils. Wide ranges of viscosity indexes, steel-on-steel friction, and other properties were tested. Full vehicle fuel economy tests were performed in a temperature controlled environment with a robotic driver. The test revealed that there was more than 3% overall FE variation compared to a reference fluid.

High boost and direct injection are effective ways for energy saving in gasoline engines. However, the occurrence of super-knock at high load has become a main obstacle for further improving power density and fuel economy. It has been known that super-knock can be induced by pre-ignition, and oil droplet auto-ignition is found to be one of the possible mechanisms. In this study, experiments were conducted in a single-cylinder thermal research engine (TRE), in which different types of oil and surrogates were directly injected into the cylinder and then led to pre-ignition and super-knock. The effect of oil injection timing, oil injection quantity, different gasoline and different oil were tested. All the oil in this work could induce pre-ignition, even though their combustion phasing was much later than that in the case of n-hexadecane.

The fuel economy and emissions performance of a Diesel engine is strongly influenced by the fuel injection process. This paper presents early results of an experimental investigation into diesel spray development carried out in a novel in-house developed optical pressure chamber capable of operating at pressure up to 50 bar and temperatures up to 900 K. The spatial evolution of a diesel spray tends to experience many transitory macroscopic phenomena that directly influence the mixing process. These phenomena are not considered highly reproducible and are extremely short lived, hence recording and understanding these transient effects is difficult. In this study, high-speed backlight-illuminated imaging has been employed in order to capture the transient dynamics of a short signal duration diesel spray injected into incremental back pressures and temperatures reaching a maximum of 10 bar and 473 K respectively.

Tracked vehicles are widely used for agriculture, construction and many other areas. Due to high emissions, hybrid electric driveline has been applied to tracked vehicles. The hybrid powertrain design for the tracked vehicle has been researched for years. Different from wheeled vehicles, the tracked vehicle not only requires high mobility while straight driving, but also pursues strong steering performance. The paper takes the hybrid track-type dozers (TTDs) as an example and proposes an optimal design of a novel power-split powertrain for TTDs. The commercial hybrid TTD usually adopts the series hybrid powertrain, and sometimes with an extra steering mechanism, which has led to low efficiency and made the structure more complicated. The proposed three-planetary-gear power-split hybrid powertrain can overcome the problems above by utilizing the characteristics of planetary gear sets.

Hybridization of vehicles is considered as the most promising technology for automakers and researchers, facing the challenge of optimizing both the fuel economy and emission of the road transport. Extensive studies have been performed on power-split hybrid electric vehicles (PS-HEVs). Despite of the fact that their excellent fuel economy performance in city driving conditions has been witnessed, a bottle neck for further improving the fuel economy of PS-HEVs has been encountered due to the inherent engine-generator-motor power circulation of the power-split system under medium-low speed cruising scenarios. Due to the special mechanical constraints of the power-split device (PSD), the conventional periodic cruising strategy like Pulse and Glide cannot be applied to PS-HEVs directly.

Hybrid electric vehicles (HEV) are essential for reducing fuel consumption and emissions. However, when analyzing different segments of the transportation industry, for example, public transportation or different sizes of delivery trucks and how the HEV are used, it is clear that one powertrain may not be optimal in all situations. Choosing a hybrid powertrain architecture and proper component sizes for different applications is an important task to find the optimal trade-off between fuel economy, drivability, and vehicle cost. However, exploring and evaluating all possible architectures and component sizes is a time-consuming task. A search algorithm, using Gaussian Processes, is proposed that simultaneously explores multiple architecture options, to identify the Pareto-optimal solutions.

Gasoline direct injection engines can greatly improve the fuel economy, but the idea mixture distribution cannot be easily controlled. In this paper, the linearized instability sheet atomization (LISA) and large eddy simulation (LES) implemented into KIVA-3V code were used to study the gasoline hollow cone spray process for gasoline direct injection (GDI) in a constant volume vessel. The three-dimensional results show that the LISA model can effectively simulate the gasoline hollow cone spray and obtain the string structure compared to the experiment data. And the velocity interpolation method can reduce the grid dependency of spray simulation. Using dense grid (about 8 million cells) in LES and RANS all can obtain the good spray tip penetration and width. Unlike diesel spray, for gasoline spray there are not big difference between the results using LES and RANS. In additional the ambient pressure significantly influence the gasoline spray shape.

When gasoline-fueled vehicles are operated in consumer service, the oil used to lubricate the engine plays a key role in engine cooling, reducing friction, maintaining efficient operation, and optimizing fuel economy. The effects of normal vehicle operation on oil deterioration have a direct impact on fuel consumption. The authors have observed substantial differences between the deterioration of engine oil and resulting fuel economy under real-world driving conditions, and the deterioration of oils and resulting fuel economy in the standard laboratory test used to assess fuel economy in North America, the Sequence VID engine test (ASTM D7589). By analyzing the data from vehicles and comparing these data to the Sequence VID the authors have proposed and evaluated several changes to the Sequence VID test that improve the correlation with real-world operation and improve test discrimination.