Search Results

Because of domestic production from renewable sources and their clean burning nature, alcohols, especially ethanol, have seen growing use as a blending agent and replacement for basic hydrocarbons in gasoline. The increasing use of alcohol in fuels raises questions on the safety of these fuels under certain non-operational situations. Modern vehicles use evaporative emission control systems to minimize environmental emissions of fuel. These systems must be relatively leak-free to function properly and are self-diagnosed by the vehicle On-Board Diagnostic system. When service is required, the service leak testing procedures may involve forcing test gases into the “evap” system and also exposure of the fuel vapors normally contained in the system to atmosphere. Previous work has discussed the hazards involved when performing shop leak testing activities for vehicles fuelled with conventional hydrocarbon gasoline [1, 2].

The selection of parameters during friction stir spot welding of Al-alloys and Mg-alloys is discussed. The role of tool rotation speed, plunge rate, and dwell time is examined in relation to the tool heating rate,temperature, force, and torque that occur during spot welding. In order to reduce the cycle time and tool force during Al- alloy spot welding, it is necessary to increase the tool rotation speed >1500 RPM. The measured peak temperature in the stir zone is determined by the rotation speed and dwell time, and is ultimately limited by the solidus of the alloy. When tool rotation speeds >1500 RPM are employed during AZ91 Mg-alloy spot welding, the tendency for melted film formation and cracking are greatly increased.

Gasoline particulate filters (GPFs) are an important aftertreatment system that enables gasoline direct injection (GDI) engines to meet current emission standardsn note of GPFs may need to improonont accumulates on the GPF during engine operation. GPFs are often ‘pa during vehicle operation when the exhaust is sufficiently hot and it contains sufficient oxygen. This paper explores the effect that engine-out soot emissions and the frequency of GPF regeneration have on GPF filtration efficiency. Two GPF technologies were tested on two engine dynamometers as well as two production vehicles on a chassis dynamometer. The engines span a wide range of engine-out particle emissions (a range of almost one order of magnitude). The filtration efficiency of the GPFs were measured with a regulation-compliant particle number system (non-volatile particles > 23 nm), as well as with a particle counter with a lower cutoff of 2.5 nm, and with a differential mobility spectrometer.

A novel processing method for fabricating high porosity microcellular ceramic foams for sound absorption applications has been developed. The strategy for fabricating the ceramic foams involves: (i) forming some shapes using a mixture of preceramic polymer and expandable microspheres by a conventional ceramic forming method, (ii) foaming the compact by heating, (iii) cross-linking the foamed body, and (iv) transforming the foamed body into ceramic foams by pyrolysis. By controlling the microsphere content and that of the base elastomer, it was possible to adjust the porosity with a very high open-cell content (ranging between 43 - 95%), high microcellular cell densities (9 × 108 - 1.6 × 109 cells/cm3) and desired expansion ratios (3 - 6 folds). Sound absorption testing has been performed using ASTM C-384 standard test. The preliminary results show that ceramic foams are candidate sound absorption materials.

Life Cycle Value Assessment (LCVA) is a decision making tool which considers environmental, economic and/or social aspects for the entire life cycle of a product or process from “cradle-to-grave”. LCVA can be used for a wide range of public policy and business decisions with the analysis being performed at various levels of rigour. By its nature, LCVA utilizes data sets of varying qualities drawn from a wide range of sources. The uncertainties in the input data obviously lead to uncertainties in the results of the LCVA analysis. To establish confidence in an LCVA's recommendations, it is important to consider these uncertainties and incorporate an assessment of uncertainty into the LCVA process. However, the diverse nature of the data sets being used makes it difficult to rigorously establish data uncertainty levels. In addition, the complexity of most life cycle models makes it difficult to trace uncertainty through the analysis process.

Fuel choices are being made today by consumers, industry and government. One such choice is whether to use reformulated gasoline to replace regular unleaded gasoline. A second choice involves the source of crude oil, with synthetic crude oil from tar sands currently expanding its share of the Canadian supply. Decision makers usually work with the direct economic consequences of their fuel choice. However, they generally lack the knowledge to measure environmental aspects of different fuel systems. This paper uses Life Cycle Value Assessment (LCVA) to demonstrate how the life cycle environmental aspects can be compared for alternative fuel choices. LCVA is an engineering decision making tool which provides a framework for the decision maker to consider the key economic and environmental impacts for the entire life cycle of alternative products or process systems.

Homogeneous Charge Compression Ignition (HCCI) engines offer high fuel efficiency and some emissions benefits. However, it is difficult to control and stabilize combustion over a sufficient operating range because the critical compression ratio and intake temperature at which HCCI combustion can be achieved varies with operating conditions such as speed and load as well as with fuel octane number. Replacing part of the base fuel with reformer gas, (which can be produced from the base hydrocarbon fuel), alters HCCI combustion characteristics in varying ways depending on the replacement fraction and the base fuel auto-ignition characteristics. Injecting a blend of reformer gas and base fuel offers a potential HCCI combustion control mechanism because fuel injection quantities and ratios can be altered on a cycle-by-cycle basis.

Homogeneous Charge Compression Ignition (HCCI) combustion offers high fuel efficiency and some emissions benefits. However, it is difficult to control and stabilize combustion over a significant operating range because the critical compression ratio and intake temperature at which HCCI combustion can be achieved vary with operating conditions such as speed and load as well as with fuel octane number. Replacing part of the base fuel with reformer gas, (which can be produced from the base hydrocarbon fuel), alters HCCI combustion characteristics in varying ways depending on the replacement fraction and the base fuel auto-ignition characteristics. Because fuel injection quantities and ratios can be altered on a cycle-by-cycle basis during operation, injecting a variable blend of reformer gas and base fuel offers a potential HCCI combustion control mechanism.

One of the key challenges of the wood polymer composites (WPC) is the inadequate toughness partly due to the incompatibility of the natural fibres and PP matrix. In this work, we performed the surface modification of the natural fibre by either in-situ grafting polymerization of butyl acrylate (PBA) or adsorbing matrix-compatible cationic PBA latex on the fibre surfaces. The results indicated that the mechanical properties of the polypropylene (PP) composites containing the modified fibres, unnotched Izod impact strength in particular, have been improved significantly. The influencing factors and the mechanism of toughening process have also been preliminarily investigated.

We have studied the effects of water droplets presence in the PEM Fuel cell channel and the way they influence dynamics of the two-phase flow in the channel numerically. Dynamic behavior of a droplet on the surface of a channel has been modeled under the influence of surrounding fluid. Optimal conditions for the displacement of water droplet in the channel flow sought. For this purpose, the yield conditions for the displacement of liquid droplet on the surface of the channel under the influence of channel fluid are determined. The numerical solution is based on solving Navier-Stokes equations for Newtonian liquids. The study includes the effect of interfacial forces with constant surface tension, also effect of adhesion between the wall and droplet accounted by implementing contact angle at the wall. The Volume-Of-Fluid method is used to numerically determine the deformation of free surface.

Motorized transport has become an essential part of our world economic system with an ever-increasing number of vehicles on the road. However, considering the depletion of energy resources and the aggravation of greenhouse gas issues, it is critical to improve vehicle fuel consumption. These demands are moving us toward advanced engine and powertrain technologies. However, understanding our progress also requires improvements in the way we measure and certify vehicle emissions and fuel economy performance. This paper describes the use of an on-board fuel consumption and emissions measurement system to develop on-road fuel consumption functions that can be used to quantify the fuel economy impact of vehicle, road and traffic control changes. The system uses an ECM OBD-II scanner, a Mass Air Flow meter and an emissions analyzer to monitor fuel consumption and exhaust CO2 emission rates (in g/s) as well as vehicle speed and other parameters.

Friction stir spot welding of Mg-alloy AZ91 is investigated. The temperature cycles within the stir zone and in the TMAZ region are examined using thermocouples, which are located within the tool itself and also by locating thermocouples in drilled holes at specific locations relative to the bottom of the tool shoulder and the periphery of the rotating pin. The measured temperatures in the stir zone range from 437°C to 460°C (0.98Ts, where Ts is the solidus temperature in degrees Kelvin) in AZ91 spot welds produced using plunge rates from 2.5 and 25 mm/s. The thermal cycle within the stir zone formed during AZ91 spot welding could not be measured by locating thermocouples within the workpiece in drilled holes adjacent to the periphery of the rotating pin.

Although HCCI engines promise low NOx emissions with high efficiency, they suffer from a narrow operating range between knock and misfire because they lack a direct means of controlling combustion timing. A series of previous studies showed that reformer gas, (RG, defined as a mixture of light gases dominated by hydrogen and carbon monoxide), can be used to control combustion timing without changing mixture dilution, (λ or EGR) which control engine load. The effect of RG blending on combustion timing was found to be mainly related to the difference in auto-ignition characteristics between the RG and base fuel. The practical effectiveness of RG depends on local production using a fuel processor that consumes the same base fuel as the engine and efficiently produces high-hydrogen RG as a blending additive.

Natural gas is a challenging fuel for HCCI engines because its single-stage ignition and rapid combustion make it difficult to optimize combustion timing over a significant load range. This study investigates direct injection of a pilot quantity of high-cetane fuel near TDC as a range extension and combustion control mechanism for natural gas HCCI engines. The EGR and load range is studied in a supercharged natural gas HCCI engine equipped with external EGR, intake heating and a direct injection system for n-heptane pilot fuel. The operating range and emissions are of primary interest and are compared between both the baseline HCCI engine with variable intake temperature and the direct injected HCCI (DI-HCCI) engine with constant intake temperature. Test results show the EGR and load range at fixed intake temperature can be extended using pilot direct injection.

Life Cycle Analysis (LCA) considers the key environmental impacts for the entire life cycle of alternative products or processes in order to select the best alternative. An ideal LCA would be an expensive and time consuming process because any product or process typically involves many interacting systems and a considerable amount of data must be analysed for each system. Practical LCA methods approximate the results of an ideal analysis by setting limited analysis boundaries and by accepting some uncertainty in the data values for the systems considered. However, there is no consensus in the LCA field on the correct method of selecting boundaries or on the treatment of data set uncertainty. This paper demonstrates a new method of selecting system boundaries for LCA studies and presents a brief discussion on applying Monte Carlo Analysis to treat the uncertainty questions in LCA.

Eco-efficient and cost effective natural fibre - thermoplastic composites have gained attention to a great extent in the automotive industry. Most of the OEM specifications for automotive interior parts, for example, instrument panels, recommend the composite should have a minimum flexural modulus of 1900 MPa, a notched Impact strength greater than 150 J/m at room temperature and a melt flow index of 5 g/10min and above [1, 2 and 3]. The objective of this work was to develop a high performance hybrid composite by injection molding process of the composites made from natural fibre in combination with glass fibre or calcium carbonate in a thermoplastic matrix to meet the specifications required for automotive interior parts applications. Mechanical properties, such as tensile and flexural strengths and moduli of the composites prepared, were found to be highly promising.

In this work hemp fibers were chemically treated in order to improve the fiber/matrix interaction in hemp fiber/unsaturated polyester composites prepared by a Resin Transfer Molding (RTM) process. Chemicals used for paper sizing (AKD, ASA, Rosin Acid and SMA) as well as a silane compound and sodium hydroxide were used to modify the fibers' surface. The tensile, flexural and impact properties of the resulting materials were measured. A slight improvement in mechanical properties was observed for the SMA, silane and alkali treated specimens. However close analysis of these tests and of the fracture surface of the samples showed that there was no amelioration of the fiber/matrix adhesion. It was found that predicted tensile strengths using the rule of mixture were very close to the experimental values obtained in this work. Finally the properties of an hybrid glass fiber/hemp fiber composite were found to be very promising

Natural fiber mat (NMT) composites are ecologically and energetically beneficial because of their light-weight at high fibre content. This study demonstrated that the use of loose natural fibre in NMT process could lead to tremendous improvement in the shock absorption properties. It is also concluded that in NMT process fibre length above the critical length of fibre hardly affects the mechanical strength. The process is relatively easy one-step molding technique to provide large dimensions. The process also demonstrated promise in reducing the cost of the composite parts by minimizing/eliminating the use of natural fibre nonwoven mat and replacement of glass fibre.

Automotive tailpipe emissions are a significant contribution to urban air quality problems.(1) However, it is difficult to quantify the extent of that contribution and to quantify any progress in solving the problem. Emissions inventories are commonly based on vehicle registrations, assumed mileage and a set of emission factors. The emission factors are based on dynamometer testing of selected vehicles undertightly controlled conditions. Actual vehicle operation in any urban area encompasses a wider range of vehicles, operating conditions and ambient conditions. Given the highly tuned nature of current engine management systems, the actual in-use emissions levels can be highly sensitive to non-standard ambient and operating situations.(2,3,4,5) This paper describes an on-board system used to record ambient conditions, driving behavior, vehicle operating parameters, fuel consumption and exhaust emissions.

The 2003 University of Alberta FutureTruck team is converting a 2002 Ford Explorer to be a pre-transmission, parallel Hybrid Electric Vehicle (HEV). The goals for the FutureTruck competition are to achieve increased fuel economy, while reducing emissions and maintaining the functionality of the stock SUV. The University of Alberta design places a 2.0L Zetec engine, running on E85, in parallel with a Unique Mobility brushless DC motor. In the Explorer the engine and motor will have peak power outputs of 110 kW and 60 kW. The motor will draw electricity from a nominal 200V lithium ion battery pack that is in parallel with ultracapacitor banks. Further modifications integrate this drive train into the vehicle and use control logic to provide a seamless, customer friendly package.