Search Results

Fully Variable Valve Actuation (FVVA) systems enable to employ a wide range of combustion strategies by providing the actuation of a gas exchange valve at an arbitrary point in time, with variable lift and adjustable ramps for opening and closing. Making such a system ready for the market requires appropriate fault-diagnostic functionality. Here, we focus on diagnosis possibilities by using air intake system sensors such as Manifold Absolute Pressure (MAP) sensors. Results obtained on a 4-cylinder test bench engine are presented for the early intake opening strategy under different loads, and at medium range rotational speeds on steady-state conditions. It is shown that detection and identification of the different critical faults on each actuator is possible by using a Fourier series signal model of the MAP sensor.

Electromagnetic Compatibility (EMC) requirements and the effort to fulfill them are increasing steadily in automotive applications. This paper demonstrates the usage of virtual prototyping to efficiently investigate the EMC behavior of a gasoline direct injection system. While the system worked functionally as designed, tests indicated that current and especially future client-specific EMC limits could not be met. The goal of this investigation was to identify and eliminate the cause of EMC emissions using a virtual software prototype including the controller ASIC, boost converter, pi filter, injection valves and wire harness. Applying virtual prototyping techniques it was possible to capture the motor control system in a simulation model which reproduced EMC measurements in the frequency ranges of interest.

In order to reduce the spark-ignition engine exhaust-gas emission and fuel consumption, it is essential that the required air/fuel ratio is maintained under all operating conditions. An important contribution to this claim is delivered by the injection valve by metering the fuel precisely and producing fine atomization. In this report experimental methods to get specific measuring information and methods for optimizing flow in injection valves are described. Original valves as well as large-scale models were used for the investigations concerning the steady and unsteady-flow characteristics, and were equipped with a number of different sensors. Holograms of the short-time recording of the spray cone are generated and used for the quantification of the atomization quality when injecting into atmospheric pressure and into vacuum, thus complying with the conditions encountered in the engine intake-manifold.

The electronically-governed diesel distributor injection pump, with the proven sleeve control of injection quantity, has been in production at Bosch since 1987. Long-term development resulted in a solenoid-valve controlled injection pump. The function and component assemblies, consisting of the injection pump, solenoid valve and control unit, provide an even more flexible injection system. Of particular advantage with this type of system are the high dynamics of the fuel quantity, matching of each individual injection and the exact pump-specific fuel quantity compensation at numerous map points. Further advantages are the selection of timing and fuel injection rate independent of each other, as well as the ability to provide the correct timing even at cranking speeds. The entire system, with emphasis on the injection pump and the solenoid valve, are described for IDI engines in this paper.

Nowadays fully-flexible valve control is considered to be the most promising improvement measure for SI-engines besides or in combination with direct fuel injection. Engine producers investigate the readability of a huge variety of systems, but at present only simple systems are applied in production engines, which fulfil only a part of the requirements. Although hydraulic systems are very suitable for finding optimum valve control strategies, the advantages of mechanical systems for series requirements are obvious. Thus, after development of mechanical phase shifters and mechanical systems with up to three selectable valve lift curves, it seems to be logical to use the advantages and experiences with mechanical systems to realize a fully-flexible valve control as well. In this context a new mechanical valve gear called delta-st (delta-st = delta control) for continuous adjustment of valve lift, opening duration and phase angle was developed at the University of Karlsruhe, Germany.

In mobile R-744 A/C units mechanical expansion devices (e.g. orifice tubes) or electronic valves (e.g. PWM-valves) can be used. Besides the costs, aspects like coefficient of performance (COP), cooling capacity or control behavior - especially for extreme conditions - influence the choice of the valve type. This paper will present a comparison between an ideal electronic valve and a two stage mechanical orifice tube under full load and part load conditions. The influence of the expansion valve on COP and cooling capacity in different ambient conditions can be sufficiently described with steady-state simulations. The simulation tools used for this work are based on Modelica/Dymola. The simulation results show that for European climate conditions the use of two-stage orifices might increase fuel consumption.

Within the Robert Bosch Diesel Injection Pump Program, the MW and P pumps have a fundamental significance concerning medium-duty and heavy- duty engines. These engines have developed considerably in the last years with regard to combustion efficiency and emission reduction. In order to reach these new targets, specific developments of the pump were necessary to realize injection pressure of 900 bar and 1200 bar for the MW and P pumps, respectively. A further development emphasis of the past years was the development of a robust electronic governor concept to take advantage of this new technology. The topics of the paper are: Further development of the pump drivetrain and housing to cope with the difficulties inherent in producing 1000 bar. Development of constant-pressure valves. Preparation of the electronic governor concept for commercial vehicles. Development results of the electro-magnetic and electro-hydraulic actuators.