Search Results

Exhaust Gas Recirculation (EGR) coolers are commonly used in on-road and off-road diesel engines to reduce the recirculated gas temperature in order to reduce NOx emissions. One of the common performance behaviors for EGR coolers in use on diesel engines is a reduction of the heat exchanger effectiveness, mainly due to particulate matter (PM) deposition and condensation of hydrocarbons (HC) from the diesel exhaust on the inside walls of the EGR cooler. According to previous studies, typically, the effectiveness decreases rapidly initially, then asymptotically stabilizes over time. Prior work has postulated a deposit removal mechanism to explain this stabilization phenomenon. In the present study, five field aged EGR cooler samples that were used on construction machines for over 10,000 hours were analyzed in order to understand the deposit structure as well as the deposit composition after long duration use.

An experimental study is performed for homogeneous charge compression ignition (HCCI) combustion focusing on late phasing conditions with high cyclic variability (CV) approaching misfire. High CV limits the feasible operating range and the objective is to understand and quantify the dominating effects of the CV in order to enable controls for widening the operating range of HCCI. A combustion analysis method is developed for explaining the dynamic coupling in sequences of combustion cycles where important variables are residual gas temperature, combustion efficiency, heat release during re-compression, and unburned fuel mass. The results show that the unburned fuel mass carries over to the re-compression and to the next cycle creating a coupling between cycles, in addition to the well known temperature coupling, that is essential for understanding and predicting the HCCI behavior at lean conditions with high CV.

The role of automotive electronics in light duty vehicles is continuing to expand rapidly. In this paper an overview of a 1986 Delphi forecast of major trends is presented. Trends discussed include electronics as a fraction of vehicle and component cost and projections of basic vehicle features supported by electronic technology. In addition, basic trends in diagnostics and multiplexing are presented. Several issues in support of automotive electronics are discussed, including the systems approach to vehicle engineering, the importance of developing a proper market strategy, and the continued major role of energy economics. The Delphi forecasting technique and its governing concepts are reviewed as a method to predict the future of automotive technology.

In applications of the Energy Finite Element Analysis (EFEA) there is an increasing need for developing comprehensive models with a large number of elements which include both structural and interior fluid elements, while certain parts of the structure are considered to be exposed to an external fluid loading. In order to accommodate efficient computations when using simulation models with a large number of elements, joints, and domains, a substructuring computational capability has been developed. The new algorithm is based on dividing the EFEA model into substructures with internal and interface degrees of freedom. The system of equations for each substructure is assembled and solved separately and the information is condensed to the interface degrees of freedom. The condensed systems of equations from each substructure are assembled in a reduced global system of equations. Once the global system of equations has been solved the solution for each substructure is pursued.

A multi-body dynamics model of the U.S. Army3s High Mobility Multi-purpose Wheeled Vehicle (HMMWV) has been created using commercial software (ADAMS) to simulate and analyze the vehicle3s rollover behavior. However, manual operation of such simulation and analysis for design purposes is prohibitively expensive and time consuming, limiting the engineers3 ability to utilize the model fully and extract from it useful design information in a timely, cost-effective manner. To address this challenge, a commercial system integration and optimization software (OPTIMUS) is utilized in order to automate the simulation processes and to enable the more complex uncertainty-based analysis of the HMMWV rollover behavior under a variety of external conditions. Challenges involved in integrating the software are highlighted and remedies are discussed. Rollover analysis results from using the integrated model and automated simulation are also presented.

Many highway accidents are caused by distracted drivers and those suffering from drowsy driver syndrome. A driver alert indicating a lane departure could thwart such accidents, saving lives and making our roads safer. Products called Lane Departure Warning Systems (LDWS) have been developed to alert drivers of a lane departure. However, due to their high cost, lane departure warning systems are available only on luxury vehicles, barring their benefits from the majority of drivers. With Field Programmable Gate Arrays (FPGA) becoming more powerful and more affordable, a LDWS implementation utilizing hardware rather than software to conduct image processing eliminates the need for a costly high-power microprocessor, and could bring LDWS to a broader user base. This paper will discuss an FPGA based approach to LDWS. The proof-of-concept system is based on a Xilinx FPGA, taking its image data from an off-the-shelf NTSC camera.

In order to develop confidence in numerical models which are used for automotive crash simulations, results are compared with test data. Modeling assumptions are made when constructing a simulation model for a complex system, such as a vehicle. Through a thorough understanding of the modeling assumptions an appropriate set of variables can be selected and adjusted in order to improve correlation with test data. Such a process can lead to better modeling practices when constructing a simulation model. Comparisons between the time history of acceleration responses from test and simulations are the most challenging. Computing accelerations correctly is more difficult compared to computing displacements, velocities, or intrusion levels due to the second order differentiation with time. In this paper a methodology for enabling the update of a simulation model for improved correlation is presented.

While the results are generally the most exciting aspects of an LCI study, the details of the LCI model that generates the results are equally significant; particularly when modeling the life cycle of an automobile. The modeling challenges faced in conducting the US AMP LCI of a mid-sized vehicle based on the 1995 Lumina, Intrepid and Taurus are highlighted. The number of parts (over 20,000), supply chain complexity, materials composition, and the demanding set of OEM requirements for model features required special LCI methods and solutions. The LCI model and selected results are compared with previous studies, and recommendations for improvements in the USAMP LCI model are also provided. This paper is one of six SAE publications discussing the results and execution of the USCAR AMP Generic Vehicle LCI. The papers in this series are (Overview of results 982160, 982161, 982162, 982168, 982169, 982170).

A series of inflator tank tests was carried out to determine the amount of transient heat losses to the tank wall during these tests. The time history data of tank wall temperature, and tank interior gas temperature and pressure, were measured. The tank wall temperature data were analyzed using an inverse heat conduction method to generate the transient heat loss fluxes from the tank gas to the tank wall. The validity of the results are discussed along with the physical reasoning and experimental observations. This is the first part of an effort in a research project to develop a comprehensive heat transfer model to predict the transient heat losses to the tank wall during the inflator tank test.

The attractiveness of the hydraulic hybrid concept stems from the high power density and efficiency of the pump/motors and the accumulator. This is particularly advantageous in applications to heavy vehicles, as high mass translates into high rates of energy flows through the system. Using dry case hydraulic pumps further improves the energy conversion in the system, as they have 1-4% better efficiency than traditional wet-case pumps. However, evacuation of fluid from the case introduces air bubbles and it becomes imperative to address the deaeration problems. This research develops a bubble elimination efficiency testing apparatus (BEETA) to establish quantitative results characterizing bubble removal from hydraulic fluid in a cyclone deaeration device. The BEETA system mixes the oil and air according to predetermined ratio, passes the mixture through a cyclone deaeration device, and then measures the concentration of air in the exiting fluid.

At the forefront of intelligent vehicle technologies are vehicle-to-vehicle communication (V2V) and vehicle-infrastructure integration (VII). Their capabilities can be added to currently-available systems, such as adaptive cruise control (ACC), to drastically decrease the number and severity of collisions, to ease traffic flow, and to consequently improve fuel efficiency and environmental friendliness. There has been extensive government, industry, and academic involvement in developing these technologies. This paper explores the capabilities and challenges of vehicle-based technology and examines ways that policymakers can foster implementation at the federal, state, and local levels.

The Human Motion Simulation Framework (Framework) is a hierarchical set of algorithms for predicting and analyzing task-oriented human motion. The Framework was developed to improve the performance of commercial human modeling software by increasing the accuracy of predicted motions and the speed of generating simulations. This paper presents the addition of stair ascending and descending to the Transition Stepping and Timing (Transit) model, a component of the Framework that predicts gait and acyclic stepping.

Assessments of reach capability using human figure models are commonly performed by exercising each joint of a kinematic chain, terminating in the hand, through the associated ranges of motion. The result is a reach envelope determined entirely by the segment lengths, joint degrees of freedom, and joint ranges of motion. In this paper, the validity of this approach is assessed by comparing the reach envelopes obtained by this method to those obtained in a laboratory study of men and women. Figures were created in the Jack human modeling software to represent the kinematic linkages of participants in the laboratory study. Maximum reach was predicted using the software's kinematic reach-envelope generation methods and by interactive manipulation. Predictions were compared to maximum reach envelopes obtained experimentally. The findings indicate that several changes to the normal procedures for obtaining maximum reach envelopes for seated tasks are needed.

Improving the performance characteristics of a typical disc brake encompasses a number of design strategies as well as limitations imposed by cost objectives. Utilizing pad loading uniformity in a design is one strategy that offers an improvement in desired performance characteristics, including a reduction in tapered lining wear as well as a possible reduced propensity for noise generation. To approach this design strategy, a procedure has been developed to tailor the brake pad lining profile to maximize pad loading uniformity in a multibody dynamics model of a typical disc brake. In determining an optimal lining configuration, a suitable compromise for gaining beneficial performance improvements in a cost effective manner is reached. The implementation of this design strategy involves the parametric definition of the lining profile by introducing a series of variables that are linked to the profile markers.

The Indirect Boundary Element Analysis is employed for developing a computational pass-by noise simulation capability. An inverse analysis algorithm is developed in order to generate the definition of the main noise sources in the numerical model. The individual source models are combined for developing a system model for pass-by noise simulation. The developed numerical techniques are validated through comparison between numerical results and test data for component level and system level analyses. Specifically, the source definition capability is validated by comparing the actual and the computationally reconstructed acoustic field for an engine intake manifold. The overall pass-by noise simulation capability is validated by computing the maximum overall sound pressure level for a vehicle under two separate driving conditions.

The Energy Finite Element Analysis(EFEA) is a recent development for high frequency vibro-acoustic analysis, and constitutes an evolution in the area of high frequency computations. The EFEA is a wave based approach, while the SEA is a modal based approach. In this paper the similarities in the theoretical development of the two methods are outlined. The main scope of this paper is to establish the validity of the EFEA by analyzing several complex structural-acoustic systems. The EFEA solutions are compared successfully to SEA results and to solutions obtained from extremely dense conventional FEA models.

This paper presents an extension of our previous work on decomposition-based assembly synthesis [1], where the 3D finite element model of a vehicle body-in-white (BIW) is optimally decomposed into a set of components considering the stiffness of the assembled structure under given loading conditions, and the manufacturability and assemblability of each component. The stiffness of the assembled structure is evaluated by finite element analyses, where spot-welded joints are modeled as linear torsional springs. In order to allow close examinations of the trade-off among stiffness, manufacturability, and assemblability, the optimal decomposition problem is solved by multi-objective genetic algorithm [2,3], with graph-based crossover [4,5], combined with FEM analyses, generating Pareto optimal solutions. Two software programs are developed to implement the proposed method.

In-cylinder fluid velocity is measured in an optically accessible, fired HSDI engine at idle. The velocity field is also calculated, including the full induction stroke, using multi-dimensional fluid dynamics and combustion simulation models. A detailed comparison between the measured and calculated velocities is performed to validate the computed results and to gain a physical understanding of the flow evolution. Motored measurements are also presented, to clarify the effects of the fuel injection process and combustion on the velocity field evolution. The calculated mean in-cylinder angular momentum (swirl ratio) and mean flow structures prior to injection agree well with the measurements. Modification of the mean flow by fuel injection and combustion is also well captured.

ADAS features development involves multidisciplinary technical fields, as well as extensive variety of different sensors and actuators, therefore the early design process requires much more resources and time to collaborate and implement. This paper will demonstrate an alternative way of developing prototype ADAS concept features by using remote control car with low cost hobby type of controllers, such as Arduino Due and Raspberry Pi. Camera and a one-beam type Lidar are implemented together with Raspberry Pi. OpenCV free open source software is also used for developing lane detection and object recognition. In this paper, we demonstrate that low cost frame work can be used for the high level concept algorithm architecture, development, and potential operation, as well as high level base testing of various features and functionalities. The developed RC vehicle can be used as a prototype of the early design phase as well as a functional safety testing bench.

Digital human models (DHM) are now widely used to assess worker tasks as part of manufacturing simulation. With current DHM software, the simulation engineer or ergonomist usually makes a manual estimate of the likely worker standing location with respect to the work task. In a small number of cases, the worker standing location is determined through physical testing with one or a few workers. Motion capture technology is sometimes used to aid in quantitative analysis of the resulting posture. Previous research has demonstrated the sensitivity of work task assessment using DHM to the accuracy of the posture prediction. This paper expands on that work by demonstrating the need for a method and model to accurately predict worker standing location. The effect of standing location on work task posture and the resulting assessment is documented through three case studies using the Siemens Jack DHM software.