Search Results

Recent field data have shown that the occupant protection in vehicle rear seats failed to keep pace with advances in the front seats likely due to the lack of advanced safety technologies. The objective of this study was to optimize advanced restraint systems for protecting rear seat occupants with a range of body sizes under different frontal crash pulses. Three series of sled tests (baseline tests, advanced restraint trial tests, and final tests), MADYMO model validations against a subset of the sled tests, and design optimizations using the validated models were conducted to investigate rear seat occupant protection with 4 Anthropomorphic Test Devices (ATDs) and 2 crash pulses.

Frontal crashes (11-1 o'clock) were reviewed from the National Accident Severity Study file (NASS) for years 1980-87. Adult drivers and front right passengers, with lower extremity injuries of the pelvis, thigh, knee, leg or ankle/foot were reviewed. Analysis of age differences, injury contacts, and effectiveness of the 3-point restraint system were studied. Unrestrained drivers have a higher frequency of knee injuries than passengers, fewer leg injuries than passengers and both have the same frequency of ankle/foot injuries. Older unbelted drivers have more injuries to the pelvis, leg, and ankle/foot region than do young drivers. Passengers have more leg injuries. The instrument panel is the major contact for most of the lower extremity injuries. Lap/shoulder belts significantly reduce lower extremity injury frequency.

The factors that influence airbag-induced upper-extremity injuries sustained by drivers were investigated in this study. Seven unembalmed human cadavers were used in nineteen direct-forearm-interaction static deployments. A single horizontal-tear-seam airbag module and two different inflators were used. Spacing between the instrumented forearm and the airbag module was varied from 10 cm to direct contact in some tests. Forearm-bone instrumentation included triaxial accelerometry, crack detection gages, and film targets. Internal airbag pressure was also measured. The observed injuries were largely transverse, oblique, and wedge fractures of the ulna or radius, or both, similar to those reported in field investigations. Tears of the elbow joint capsule were also found, both with and without fracture of the forearm.

Four unembalmed human cadavers were used in eight direct-forearm-airbag-interaction static deployments to assess the relative aggressivity of two different airbag modules. Instrumentation of the forearm bones included triaxial accelerometry, crack detection gages, and film targets. The forearm-fracture predictors, peak and average distal forearm speed (PDFS and ADFS), were evaluated and compared to the incidence of transverse, oblique, and wedge fractures of the radius and ulna. Internal-airbag pressure and axial column loads were also measured. The results of this study support the use of PDFS or ADFS for the prediction of airbag-induced upper-extremity fractures. The results also suggest that there is no direct relationship between internal-airbag pressure and forearm fracture. The less-aggressive system (LAS) examined in this study produced half the number of forearm fracture as the more-aggressive system (MAS), yet exhibited a more aggressive internal-pressure performance.

This paper describes the design and development of a family of surrogate child restraints that are intended for use in developing and testing occupant sensing and classification systems. Detailed measurements were made of the geometry and mass distribution characteristics of 34 commercial child restraints, including infant restraints, convertibles, combination restraints, and boosters. The restraints were installed in three test seats with appropriately sized crash dummies to obtain data on seat-surface pressure patterns and the position and orientation of the restraint with belt loading. The data were used to construct two surrogates with removable components. The convertible surrogate can be used to represent a rear-facing infant restraint with or without a base, a rear-facing convertible, or a forward-facing convertible. The booster surrogate can represent a high-back belt-positioning booster, a backless booster, or a forward-facing-only restraint with a five-point harness.

Advanced airbag systems use a variety of sensors to classify vehicle occupants so that the airbag deployment can be modulated accordingly. One potential input to such systems is the distribution of pressure applied to the seat surface by the occupant. However, the development of such systems is hindered by the lack of suitable human surrogates. The OCATD program has developed two new surrogates for advanced airbag applications representing a small adult woman and a six-year-old child. This paper describes the development of performance specifications for the OCATDs based on a study of the seat surface pressure distributions produced by vehicle occupants. The pressure distributions of sixty-eight small women and children ranging in body weight between 23 and 48 kg were measured on four seats in up to twelve postures per seat. The data were analyzed to determine the parameters of the pressure distribution that best predict occupant body weight.

As part of the Automotive Seat and Package Evaluation and Comparison Tools (ASPECT) program, UMTRI researchers developed a new H-point manikin that is intended to replace the current SAE J826 manikin. The original manikin is used in many automotive applications, including as a platform for a belt-fit test device (BTD). In the current project, components and procedures were developed to measure belt fit using the ASPECT manikin. Contoured lap and torso forms were constructed using anthropometric data from an earlier UMTRI study. Prototype forms were mounted on the ASPECT manikin for testing in a laboratory fixture and in vehicles. The testing demonstrated that the ASPECT-BTD produces consistent measures of belt fit that vary in expected ways with belt geometry.

The effects of child safety seats have been well documented in the medical literature. Scattered throughout the medical literature are individual case reports of cervical injury to children restrained in child restraint systems. A review of the literature is provided identifying previous documented cases. The authors also provide new case details of children with cervical spine injury without head contact. An overview of the growth of the infant and specific details in the cervical spine that may contribute to significant cervical injury without head impact is presented.

A round-robin center of gravity height measurement study was conducted to assess current practice in the measurement of the vertical position of the center of gravity (c.g.) of light truck-type vehicles. The study was performed by UMTRI for the Motor Vehicle Manufacturers Association. The laboratories participating in the study were those of Chrysler Corporation, Ford Motor Company, General Motors Corporation, and the National Highway Traffic Safety Administration. The primary objectives of this study were (i) to determine to what extent the differing experimental procedures used by the participating laboratories at the time of the study result in significant differences in the measured vertical position of the center of mass of light truck-type vehicles, and (ii) to gain insight into the physical causes of such differences.

Law enforcement officers (LEO) make extensive use of vehicles to perform their jobs, often spending large portions of a shift behind the wheel. Few LEO vehicles are purpose-built; the vast majority are modified civilian vehicles. Data from the field indicate that LEO suffer from relatively high levels musculoskeletal injury that may be due in part to poor accommodation provided by their vehicles. LEO are also exposed to elevated crash injury risk, which may be exacerbated by a compromise in the performance of the occupant restraint systems due to body-borne equipment. A pilot study was conducted to demonstrate the application of three-dimensional anthropometric scanning and measurement technology to address critical concerns related to vehicle design. Detailed posture and belt fit data were gathered from five law enforcement officers as they sat in the patrol vehicles that they regularly used and in a mockup of a mid-sized vehicle.

Tilt-table testing is one means of quantifying the static roll stability of highway vehicles. By this technique, a test vehicle is subjected to a physical situation analogous to that experienced in a steady state turn. Although the analogy is not perfect, the simplicity and fidelity of the method make it an attractive means for estimating static rollover threshold. The NHTSA has suggested the tilt-table method as one means of regulating the roll stability properties of light trucks and utility vehicles. One consideration in evaluating the suitability of any test method for regulatory use is repeatability, both within and among testing facilities. As a first step toward evaluating the repeatability of the tilt-table method, an experimental study examining the sensitivity of tilt-table test results to variables associated with methodology and facility was conducted by UMTRI for the Motor Vehicle Manufacturers Association. This paper reports some of the findings of that study.

Late model passenger cars and light trucks incorporate occupant protection systems with airbags and knee restraints. Knee restraints have been designed principally to meet the unbelted portions of FMVSS 208 that require femur load limits of 10-kN to be met in barrier crashes up to 30 mph, +/- 30 degrees utilizing the 50% male Anthropomorphic Test Device (ATD). In addition, knee restraints provide additional lower-torso restraint for belt-restrained occupants in higher-severity crashes. An analysis of frontal crashes in the University of Michigan Crash Injury Research and Engineering Network (UM CIREN) database was performed to determine the influence of vehicle, crash and occupant parameters on knee, thigh, and hip injuries. The data sample consists of drivers and right front passengers involved in frontal crashes who sustained significant injuries (Abbreviated Injury Scale [AIS] ≥ 3 or two or more AIS ≥ 2) to any body region.

Although driver-side airbag systems provide protection against serious head and chest injuries in frontal impacts, injuries produced by the airbag itself have also been reported. Most of these injuries are relatively minor, and consist primarily of skin abrasions and burns. Previous investigations have addressed the mechanisms of airbag-induced skin abrasion. In the current research, laboratory studies related to the potential for thermal burns due to high-temperature airbag exhaust gas were conducted. A laboratory apparatus was constructed to produce a 10-mm-diameter jet of hot air that was directed onto the leg skin of human volunteers in time-controlled pulses. Skin burns were produced in 70 of 183 exposures conducted using air temperatures ranging from 350 to 550°C, air velocities from 50 to 90 m/s, and exposure durations from 50 to 300 ms.

The objective of this analysis is to evaluate the effectiveness of restraints in preventing injury-producing contacts of specific body regions, such as the head or chest, with specific interior components. In order to make comparisons by restraint use, an injury rate is calculated as the number of injury-producing contacts per hundred involved occupants. Data, including the Occupant Injury Classification (OIC), are from the 1988-92 National Accident Sampling System (NASS) Crashworthiness Data System (CDS). The analysis presented is limited to passenger vehicle drivers in towaway, frontal impacts. Injury-producing contact rates are compared for four restraint configurations: unrestrained, three-point belted, driver airbag alone, and driver airbag plus three-point belt. For each restraint configuration, contact rates are compared by three categories of injury severity, AIS 1, AIS 2, and AIS 3-6, body region injured, and contact area producing the injury.

In a review of 540 crashes in which the steering-wheel airbag deployed, 38% of the drivers sustained some level of upper extremity injury. The majority of these were AIS-1 injuries including abrasions, contusions and small lacerations. In 18 crashes the drivers sustained AIS-2 or-3 level upper extremity injuries, including fractures of the radius and/or ulna, or of the metacarpal bones, all related to airbag deployments. It was determined that six drivers sustained the fracture(s) directly from the deploying airbag or the airbag module cover. The remaining 12 drivers had fractures from the extremity being flung into interior vehicle structures, usually the instrument panel. Most drivers were taller than 170 cm and, of the 18 drivers, 10 were males.

The U.S. currently requires that reai-view mirrors installed as original equipment in the center and driver-side positions be flat. There has recently been interest in using nonplanar mirrors in those positions, including possibly mirrors with large radii (over 2 m). This has provided additional motivation to understand the effects of mirror curvature on drivers' perceptions of distance and speed. This paper addresses this issue by (1) reviewing the concepts from perceptual theory that are most relevant to predicting and understanding how drivers judge distance in nonplanar rearview mirrors, and (2) reviewing the past empirical studies that have manipulated mirror curvature and measured some aspect of distance perception. The effects of mirror curvature on cues for distance perception do not lead to simple predictions. The most obvious model is one based on visual angle, according to which convex mirrors should generally lead to overestimation of distances.

As a result of improved educational opportunities, handicapped children have increased exposure to transportation related risks. Many of these children require specialized orthopedic seating and posture control devices and must remain in them while riding in a vehicle. The lack of impact protection features in these seating devices introduces an unnecessary level of risk. The emphasis of this program was to demonstrate that proven restraint principles could be applied to handicapped seating without compromising the medical requirements of these units. Efforts were concentrated on two such systems: a molded-shell orthotic seat and a stroller-type Travel Chair. Sled impact tests at 30 mph and 20 g's were used to assist in the evaluation of the upgraded restraints. The results have been encouraging and have shown that handicapped seating can supply the same level of crash protection provided by conventional child restraint systems.

Recent research in the ASPECT (Automotive Seat and Package Evaluation and Comparison Tools) program has led to the development of a new method for automobile driver posture prediction, known as the Cascade Model. The Cascade Model uses a sequential series of regression functions and inverse kinematics to predict automobile occupant posture. This paper presents an alternative method for driver posture prediction using data-guided kinematic optimization. The within-subject conditional distributions of joint angles are used to infer the internal cost functions that guide tradeoffs between joints in adapting to different vehicle configurations. The predictions from the two models are compared to in-vehicle driving postures.

Few studies have systematically examined the effects of truck and bus workstation geometry on driver posture and position. This paper presents methods for determining drivers' postural responses and preferred component locations using a reconfigurable vehicle mockup. Body landmark locations recorded using a three-dimensional digitizer are used to compute a skeletal-linkage representation of the drivers' posture. A sequential adjustment procedure is used to determine the preferred positions and orientations of key components, including the seat, steering wheel, and pedals. Data gathered using these methods will be used to create new design tools for trucks and buses, including models of driver-selected seat position, eye location, and needed component adjustment ranges. The results will also be used to create accurate posture-prediction models for use with human modeling software.

Pregnant occupants pose a particular challenge to safety engineers because of their different anthropometry and the additional “occupant within the occupant.” A detailed study of the anthropometry and seated posture of twentytwo pregnant drivers over the course of their pregnancies was conducted. Subjects were tested in an adjustable seating buck that could be configured to different vehicle package geometries with varying belt anchorage locations. Each subject was tested four times over the course of her pregnancy to examine changes in seat positioning, seated anthropometry, and positioning of the lap and shoulder belts with gestational age. Data collected include preferred seating positions of pregnant drivers, proximity of the pregnant occupant to the steering wheel and airbag module, contours of the subjects’ torsos and abdomens relative to seat-belt centerline contours, and subject perceptions of their seated posture and proximity to vehicle components.