Search Results

The introduction of real driving emissions cycles and increasingly restrictive emissions regulations force the automotive industry to develop new and more efficient solutions for emission reductions. In particular, the cold start and catalyst heating conditions are crucial for modern cars because is when most of the emissions are produced. One interesting strategy to reduce the time required for catalyst heating is post-oxidation. It consists in operating the engine with a rich in-cylinder mixture and completing the oxidation of fuel inside the exhaust manifold. The result is an increase in temperature and enthalpy of the gases in the exhaust, therefore heating the three-way-catalyst. The following investigation focuses on the implementation of post-oxidation by means of scavenging in a four-cylinder, turbocharged, direct injection spark ignition engine. The investigation is based on detailed measurements that are carried out at the test-bench.

Intensified emission regulations as well as consumption demands lead to an increasing significance of unburned hydrocarbon (UHC) emissions for diesel engines. On the one hand, the quantity of hydrocarbon (HC) raw emissions is important for emission predictions as well as for the exhaust after treatment. On the other hand, HC emissions are also important for predicting combustion efficiency and thus fuel consumption, since a part of unreleased chemical energy of the fuel is still bound in the HC molecules. Due to these reasons, a simulation model for predicting HC raw emissions was developed for diesel engines based on a phenomenological two-zone model. The HC model takes three main sources of HC emissions of diesel engines into account: Firstly, it contains a sub-model that describes the fuel dribble out of the injector after the end of injection. Secondly, HC emissions from cold peripheral zones near cylinder walls are determined in another sub-model.

In order to meet increasingly stringent exhaust emission regulations, new engine concepts need to be developed. Lean combustion systems for stationary running large gas engines can reduce raw NOx-emissions to a very low level and enable the compliance with the exhaust emission standards without using a cost-intensive SCR-aftertreatment system. Experimental investigations in the past have already confirmed that a strong reduction of the charge air temperature even below ambient conditions by using an absorption chiller can significantly reduce NOx emissions. However, test bench operation of large gas engines is costly and time-consuming. To increase the efficiency of the engine development process, the possibility to use 0D/1D engine simulation prior to test bench studies of new concepts is investigated using the example of low temperature charge air cooling. In this context, a reliable prediction of engine efficiency and NOx-emissions is important.

The Institute for Polymer Testing and Polymer Science of the University of Stuttgart has been investigating automotive parts, structures and cars during their life cycle in plenty cooperation with the European automobile producers and their suppliers for the last 9 years. Therefore a holistic approach has been developed to combine tasks from technique, economic and environment in a methodology called Life Cycle Engineering (LCE). The goal is to find a way to support designer and engineers as well as police makers and public with this three-dimensional interrelated information to have the possibility to manufacture future products in a more sustainable way without loosing contact two the traditional parameters technique and costs.

Automotive electric and electronic devices are commonly tested with standard pulses at the battery lines according to ISO 7637-Part 1 and 2. As these pulses do not cover all disturbances that occur in modern passenger cars, each OEM defines its own additional test-pulses which makes it difficult for component suppliers to satisfy all existing requirements. The paper shows a comparison between measurement and simulation such as slow “ignition on” pulses of a modern passenger car. Additionally, the ability of the computing model to calculate the propagation of fast transients and characteristic pulses of currently used electric and electronic devices is demonstrated. This data can be used for the definition of new test-pulses.

The aim of this article is to show a method, how the buyer's and supplier's cost management programs can be linked via Target Costing to find ways to reduce product cost and development time through intense interaction within the whole supply chain.

The Institute for Polymer Testing and Polymer Science (IKP) is an independent institute of the University of Stuttgart. For approximately 8 years work is done on the field of Life Cycle Engineering. The first couple of years knowledge about the production of materials was collected within plenty industrial cooperation. Parallel to this a methodology for the Life Cycle Engineering approach and a software system (GaBi 1.0-2.0) were developed. Based on these information, projects for balancing single parts like bumpers, fender, air intake manifolds and oil filters followed by projects handling more complex parts or processes like several body in white, headlights, fuel tanks, green tire or coating processes were done to establish the methodology of Life Cycle Engineering as a tool for decision makers and weak point analysis. Parallel to this a methodology for an Life Cycle Inventory (LCI) for the system automobile was developed in cooperation with the Volkswagen AG in 1993.

Intensified emission regulations as well as consumption demands lead to an increasing significance of carbon monoxide (CO) emissions for diesel engines. On the one hand, the quantity of CO raw emissions is important for emission predictions as well as for the exhaust gas after treatment. On the other hand, CO emissions are also important for predicting combustion efficiency and thus fuel consumption, since a part of unreleased chemical energy of the fuel is still bound in the CO molecules. Due to these reasons, a simulation model for predicting CO raw emissions was developed for diesel engines based on a phenomenological two-zone model. The CO model takes three main sources of CO emissions of diesel engines into account: Firstly, it contains a sub model that describes CO from local understoichiometric areas. Secondly, CO emissions from overmixed regions are considered.

To meet the requirements of strict CO2 emission regulations in the future, internal combustion engines must have excellent efficiencies for a wide operating range. In order to achieve this goal, various technologies must be applied. Additionally, fuels other than gasoline should also be considered. In order to investigate the potential of the efficiency improvement, a SI engine was designed and optimized using 0D/1D methods. Some of the advanced features of this engine model include: High stroke-to-bore-ratio, variable valve timings with Miller cycle, EGR, cylinder deactivation, high turbulence concept, variable compression ratio and extreme downsizing. The fuel of choice was gasoline. With the proper application of technologies, the fuel consumption at the most relevant operating window could be decreased by approximately 10% in comparison to a state-of-the-art spark-ignited direct-injection four-cylinder passenger car engine.

There is a growing need for low-emissions concepts due to stricter emission regulations, more stringent homologation cycles, and the possibility of a ban on new engines by 2035. Of particular concern are the conditions during a cold start, when the Three-Way Catalyst is not yet heated to its light-off temperature. During this period, the catalyst remains inactive, thereby failing to convert pollutants. Reducing the time needed to reach this temperature is crucial to comply with the more stringent emissions standards. The post oxidation by means of secondary air injection, illustrated in this work, is a possible solution to reduce the time needed to reach the above-mentioned temperature. The strategy consists of injecting air into the exhaust manifold via secondary air injectors to oxidize unburned fuel that comes from a rich combustion within the cylinder.

Due to increasingly strict emission regulations, lean combustion concept has become an essential direction of internal combustion engine development to reduce engine emissions. However, lean combustion will lead high combustion instability and unpredictive engine emissions. The combustion instability is represented as the high cycle-to-cycle variation. Therefore, understanding the mechanism of cycle-to-cycle variation is crucial for the internal combustion engine design. This paper investigates the cause-and-effect chain of cycle-to-cycle variation of spark ignition engines using 3D CFD simulations with CONVERGE v3.0. The cyclic variations were simulated through Large Eddy Simulations, and the simulations based on Reynolds-averaged Navier–Stokes were used as supplements. The analysis focuses on two key factors that determine the combustion process: the turbulent intensity and the homogeneity of the air/fuel mixture.