Search Results

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

In today’s automobile industry refined NVH performance is a key feature and of high importance governing occupant comfort and overall quality impression of vehicle. In this paper interior noise and vibration measurement is done on one of the light truck and few dominant low frequency noise booms were observed in operation range. Modal analysis was done for the cabin at virtual as well as experimental level and few modes were found close to these noise booms. Vibrations were measured across the cabin mounts and it was found that the isolation of front mounts is not effective at lower frequencies. Taking this as an input, the mount design was modified to shift the natural frequency and hence improve the isolation behavior at the lowest dominant frequency. This was followed by static and dynamic measurement of the mounts at test rig level to characterize the dynamic performance and stiffness conclusion.

BSIV implementation for commercial vehicle in pans India effectively from April 2017. It’s very challenging job for performance and emission engineer to meet engine performance & fuel economy with stringent emission norms for high power and torque density HD diesel engine. In Altitude, lack of air availability & combustion energy passes by mechanical waste gate, lead to lower boost at partial load in waste gate region; which in turn leads to poor engine performance & fuel efficiency and higher turbo speed. To control the turbocharger design speed limit various methodologies adopted like engine derating or optimizing the combustion parameters leads to poor vehicle performance. Combustion parameter optimsation is having limited scope for turbocharger speed control.

Present day truck cab suspension comprises fully floating linkage type cab suspension to facilitate ride comfort. Fully floating cab has certain limitations in terms of stability of cab in dynamic articulations during vehicle running especially in off-road terrain applications. Presence on linkages leads to more wear and tear of joints and bushes which will in turn provide detrimental effect on vibration levels of cab that affects ride comfort for occupants. There is a dire need to develop a system that provides improvement in lateral and vertical stability of cab without compromising ride comfort of occupants. Durability of the product also to be met till life of vehicle. Anti-Vibration Stability Cab Mount is an unsymmetrical mount designed by compounding of elastomeric(rubber) metal bonded outer sleeves sandwiched between multistage inner mount bonded on aluminum casing. Cabin front supports are hinged to mount along with housing providing proper alignment to cab after assembly.

In the modern era of commercial vehicle industry, passenger and driver comfort is one of the major parameters that improves vehicle running time which leads to fleet owner’s profitability. Air conditioning system is one such system whose primary function is to provide the required cooling inside the cabin in hot weather conditions. An Air-conditioned truck cabin creates a comfortable environment for the driver which increases his efficiency and reduces fatigue. An AC compressor consumes power directly from the engine affecting fuel economy and vehicle performance. With ever increasing demand for energy efficient systems and thermal comfort in automobiles, AC systems should be able to deliver the required cooling performance with minimum power consumption. Therefore, reducing AC power consumption in vehicles is one of the key challenges faced by climate control engineers.

Ever-increasing operational cost, reducing profit margins & increase in competition, it is of upmost significance for fleet owners & drivers to opt for a vehicle having maximum uptime. OEM's are under immense pressure to design & develop vehicles/subsystems which are reliable enough to minimize downtime & withstand heavy overloading plus extreme operating conditions especially tippers. Vehicle systems like Wheel end (hub, bearing, and grease) which are designed & packaged according to a very stringent envelop & operate as a closed system facing all the extremities of operating conditions. This undoubtly make them prone to no. of failure modes which are resulting in vehicle unplanned stoppages, so any failure mode related to the same must be taken care with utmost importance. In commercial vehicles the bearing outer cup is in interference fit with the hub. These bearings of wheel hub have to be maintained at the wheel end play of few microns.

In the view of an eco-friendly environmental future, the major automotive manufacturers are making a move towards electric mobility. The electric vehicle helps to achieve Zero-emission. However, there are some limitations too. The zero-emission Battery electric vehicle (BEV) can provide a limited range only; the market penetration is getting difficult because of an energy storage capability. The addition of an electric vehicle with a fuel cell unit and a hydrogen supply unit can increase the range and the energy capacity of the system. Fuel cell electric vehicle (FCEV) system is faster to refill compared to plug-in Battery electric vehicle (BEV). This study deals with a behavioral analysis of Polymer Electrolyte Membrane (PEM) Fuel cell; with different drive cycles. In this, a fuel cell model developed and simulated in the SIMULINK environment with different drive cycle and results were obtained. The fuel cell controls also were analyzed for the city start/stop cycle.

With the enforcement of ever stringent emission norms, vehicular subsystems are witnessing a substantial transition from electro-mechanical to electronic control-based systems. With the inclusion of incremental modifications to be suitable for future applications, the electrical system has reached a point where it is undergoing a major transition. Further catalyzing this reform is the demand for mass passenger safety, bringing about its own set of uncompromising norms. While the implications of the regulations enforce cleaner and safer mobility, there also arises a conflict between vehicular functionality and safety. This paper enumerates on the first-hand experience of how the direct transfer of the elementary vehicle battery isolator from the prior euro-4 electrical system to the present euro-6 system resulted in a disharmonized vehicle operation when made to comply with both functionality and passenger safety norms.

Turbocharging has become an important method for increasing the power output of diesel engines. A perfectly matched turbocharger can increase the engine efficiency and decrease the BSFC. For turbocharger matching, engine manufacturers are dependent on the turbocharger manufacturers. In this paper, an analytical model is presented which could help engine manufacturers to analyze the performance of turbocharger for different load and ambient condition using compressor and turbine map provided by turbo manufacturers. The analytical model calculates the required pressure at inlet and exhaust manifold for fixed vane turbocharger with waste gate using inputs like BSFC, lambda, volumetric efficiency, turbocharger efficiency and heat loss, that are available with the engine manufacturer.

The need to develop products faster and to have designs which are first time right have put enormous pressure on the product development timelines, thus making computer aided optimization one of the most important tool in achieving these targets. In this paper, a design of experiments (DOE) study is used, to gain an insight as to, how changes to different parameters of front suspension and steering of a passenger bus affect its kinematic properties and thus to obtain an optimized design in terms of handling parameters such as bump steer, percent ackermann error and lock to lock rotation angle of steering wheel. The conventional hit and trial method is time consuming and monotonous and still is an approximate method, whereas in design of experiments (DOE), a model is repeatedly run through simulations in a single setup, for various combinations of parameter settings.