Search Results

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

Ride is considered to be one of the crucial criterion for evaluating the performance of a vehicle. Automobile industry is striving for improvement in designs to provide superior passenger comfort in Commercial vehicles segment. In Industry, Quarter-car model has been used for years to study the vehicle’s ride dynamics. But due to lower DOF involved in quarter car, the output accuracy is somewhat compromised. This paper aims in development of a 7 DOF full-car Model to perform the ride- comfort analysis for Light Duty 4*2 Commercial Bus using MATLAB Simulink which can be used to tune the suspension design to meet the required ride-comfort criteria. Firstly, experimental data and Physical Parameters are collected by performing Practical Test on commercial Bus on different road profiles. Secondly, a Full Car Mathematical Model with 7 DOF has been developed for a bus using MATLAB Simulink R2018a.

Electric vehicles have a limitation of limited range and long charging time. Energy optimization plays a very crucial role in determining the range of an electric vehicle. The innovative system proposed here gives the opportunity to reduce energy wastage and efficiently direct the electrical energy to improve the driving range of a 9 meter AC electric bus. The high voltage air conditioner unit alone consumes more than 40% of the electrical energy stored in the traction battery which reduces the driving range of the electric bus drastically. The proposed system optimizes the air conditioner utilization to direct cool air only in areas where passengers are present. Buses do not always run on full capacity, when there are less number of people in the bus the system detects the locations of the passengers using sensors and occupant detection algorithm, this enables the controller to identify the areas where cooling has to be focused and where cooling can be reduced or stopped.

Euro 6 emission norms are getting implemented in India from April 2020 and it is being viewed as one of the greatest challenges ever faced by the Indian automotive industry. In order to achieve such stringent emission norms along with top performance for vehicle, a good strategy should be incorporated to control system out NOx emissions and soot regeneration. Extruded Vanadium catalyst is deployed for this passive regeneration system with DOC (Diesel Oxidation Catalyst), DPF (Diesel Particulate Filter) and SCR (Selective Catalyst Reduction), where the amount of catalyst loading in DOC plays an apex role in deciding conversion efficiency of SCR and passive regeneration capabilities. This study mainly focuses on the impact of catalyst loading of DOC over SCR efficiency. NO2 to NOx ratio should be close to 0.5 for optimum conversion efficiency of SCR. Catalyst loading in DOC decides the amount of NO2 coming upstream to SCR.

With implementation of stringent BSVI emission norms and regulations like OBD-II on vehicle, it is essential to define the life of exhaust after treatment along with the vehicle. Diesel after treatment generally consists of DOC, DPF and SCR. Lubricating oil contains phosphorus and zinc which adversely affect the DOC. Unburned hydrocarbons (UNHBC) and SOF in tail pipe get accumulated in the DPF. This requires regeneration process where in, high temperatures in exhaust after treatment (EATS) burn the adsorbed Sulphur or phosphorus, thereby improving the conversion efficiencies. Repeated regenerations lead to ash accumulation in DPF and this reduces its capability for soot accumulation. Sulphur in the exhaust impacts SCR through NOx conversion. The present study analyzes the effect of (1) Chemical aging (2) Thermal aging on 3.77 liter diesel engine after treatment. A test cycle was prepared to run the durability for EATS.

The intensifying demand of cleaner fuelled vehicles considering current norms of BSIV and upcoming stringent norms of BSVI with low cost solutions has promoted the development of CNG and dual fuel vehicles. CNG vehicle is anticipated to discover its extensive use for environment fortification and effective deployment of energy capitals. Thus, CNG vehicles can be pretty effective in averting environment deterioration. CNG has low carbon to hydrogen ratio, this leads to very low CO2 emissions compared to gasoline and diesel vehicles. CNG engines have the potential of low NOx and particulate emissions. Natural gas vehicle development has been directed on the way to current use of direct injection and port injection with S.I. engines. Generally for low cost development, all OEMs prefer optimization of existing engines. Similarly for this project, a diesel engine was converted to S.I. engine for development of low emission CNG engine.

Diesel engines have always been popular for their low end torque and lugging abilities. With their higher thermal efficiencies through technical advancements, diesel engines are preferred powertrains in mass transportation of goods as well as people [14] [15]. A diesel engine always banks on excess air, which is subjected to higher compression ratios so as to achieve temperatures, enough to facilitate auto-ignition of diesel. With the advent of turbocharging and intercooling, the air availability is further enhanced, ensuring better combustion efficiency, lesser HC, CO and particulate matter (PM) emissions together with improved fuel efficiencies [2] [15]. Higher air availability also has its own shortcomings in the form of higher NOx (Nitrogen oxides) emissions. With stringent emission norms in place, reduction of NOx as well as PM, without sacrificing performance and fuel economy, is of utmost importance.

With the improvement of standard of living, air conditioning has widely been applied in buses. However, in air conditioning buses air distribution is still needs to be improved, One of the main reasons for this sub-quality comfort is two air flow louvers arrangement for 3x2 layout air conditioner buses. Air conditioning buses hatrack louvers are an integral part in providing comfort to passengers. General trend of the numbers of louvers provided to passengers is two louvers for three seats. Disadvantage of having conventional two louvers is that, there is always one passenger left with no option of directing air towards that person. This lead to an opportunity to design three louvers type hatrack instated of conventional two louvers hatrack, for 3x2 seating layout of buses. This way all three passengers can control the louvers for their own comfort and mass of air flow is sufficient for third passenger as well.

The air purifier industry has seen a growth in terms of demand and sales lately. All credit goes to massive Industrialization in developing countries such as India. The most harmful of the pollutants are PM 2.5 articulates and NOx Emissions. This leads to the new trend of customers become health and comfort conscious and willing to pay more for better and improved transportation. To satisfy these demands, COEM’s are developing more numbers of Air conditioning buses. Although the OEM’s are meeting this demand of quantity, the quality of air from air conditioner is still suffer. One of the main reasons for this poor air quality is because of the ineffectiveness of conventional air conditioner air filters to control particulate materials i.e. PM2.5, biological pollutants i.e. microbes, bacteria, viruses, and gaseous pollutants i.e. CO, CO2, SO2, NOX, O3 & VOCs in air. As per various researches, health problems associated with bus occupant compartment air quality appear more frequently.

Highway transportation using truck is an important transport mode of goods and product to their destination. Commercial vehicle is expensive mode of transportation so it will be protected from failure. For Heavy duty truck they are fully loaded at one side of transportation and other side empty transportation. In such case lift axle grounded when truck is loaded and when truck is empty it is in lift condition. Lift axle is play important role while loading so it is important that it should not fail. Many times lift axle fails at weld location due several load come on the axle. In this paper study of weld failure to vertical, braking and lateral load come on lift axle when truck is in loading condition. Weld failure check in CAE analysis with various load cases and compare with actual physical vehicle failure. Weld failure correlation well correlate when actual loading are consider in analysis. For analysis loading data is measure from RLDA data that will be used for analysis.

This paper focuses on partial encapsulation technique for reducing air-borne noise from the rocker cover of a commercial vehicle diesel engine. Due to increasing awareness, customers demand for improvised NVH (Noise Vibration and Harshness) performance in modern day vehicles. Better NVH performance implies better comfort for passengers as well as vehicle operator. This further increases the driver up time due to reduced driver fatigue. In order to improve NVH performance of existing vehicle and observe different noise and vibration zones, detailed noise and vibration mapping was carried out on one of our vehicle platform. It is observed that engine noise is one of the major contributors for interior noise, apart from road inputs etc.

In today’s automobile industry refined NVH performance is a key feature and of high importance governing occupant comfort and overall quality impression of vehicle. In this paper interior noise and vibration measurement is done on one of the light truck and few dominant low frequency noise booms were observed in operation range. Modal analysis was done for the cabin at virtual as well as experimental level and few modes were found close to these noise booms. Vibrations were measured across the cabin mounts and it was found that the isolation of front mounts is not effective at lower frequencies. Taking this as an input, the mount design was modified to shift the natural frequency and hence improve the isolation behavior at the lowest dominant frequency. This was followed by static and dynamic measurement of the mounts at test rig level to characterize the dynamic performance and stiffness conclusion.

Downsizing and Light weighting is the latest trend in the automotive industry to achieve more fuel efficient, compact and cost effective design of vehicles. Powertrain components compromise of more than 45% of the total vehicle weight. Automakers are putting significant efforts to reduce the weight of power train components. Integrated design of aluminum Engine Head and Intake manifold has been successfully implemented. Now currently we have identified the gear box housings for downsizing in light duty trucks i.e. Existing light duty trucks Cast Iron transmission. This design has been successfully modified with integrated clutch housing and transmission housing, using lightweight aluminum as the new material, using simulation tools. This lead to weight savings of up to 30% and cost savings of 20-25% as compared to existing cast iron designs. Using an integrated design reduces the assembly cost, makes the design more compact and gives better weight balance.

In order to stand apart from the competition, there is an ever growing demand in Indian commercial vehicle segments to reach higher fuel economy while achieving the emission goals set by the BS-VI norms. With emissions standard set by BS-VI, novel techniques to improve fuel efficiency have to be considered that have least impact with respect to NOx and soot emissions. The optimization of exhaust and intake valve lifts with respect to engine speed, technology commonly known as Variable Valve Lift and Timing (VVT/VVL), has been implemented in many passenger vehicles propelled by gasoline engine. The aim of this work is do initial assessment of utilizing the VVL method on a LMD commercial vehicle diesel engine. A 3.8 litre BS-VI turbocharged EGR engine is used for this study. Valve lift and timing optimization for better fuel efficiency at rated power engine speed is carried out by using one-dimensional thermodynamic simulation software AVL BOOST.

BSIV implementation for commercial vehicle in pans India effectively from April 2017. It’s very challenging job for performance and emission engineer to meet engine performance & fuel economy with stringent emission norms for high power and torque density HD diesel engine. In Altitude, lack of air availability & combustion energy passes by mechanical waste gate, lead to lower boost at partial load in waste gate region; which in turn leads to poor engine performance & fuel efficiency and higher turbo speed. To control the turbocharger design speed limit various methodologies adopted like engine derating or optimizing the combustion parameters leads to poor vehicle performance. Combustion parameter optimsation is having limited scope for turbocharger speed control.

With rising concerns on internal combustion engine noise levels in commercial vehicles, it is necessary to attenuate noises present in specific frequency bands. This can be achieved with the implementation of a quarter wave tube on the present exhaust system. Historically such passive attenuators have been efficient only at specific engine speeds and exhaust gas temperatures. A new folded adaptive quarter wave tube design is proposed here which can give significant noise attenuation at various engine operating conditions. The proposed design eliminates the requirement of complex electronic actuating mechanisms for the adaptive quarter wave tubes and replaces the same by perforated diaphragms and adjustable end plates, which are more robust and effective. The module can replace the turbo S-flow single chambered muffler which is installed on most of the commercial vehicles. A design is conceptualized and developed using CAD tools.

Present day truck cab suspension comprises fully floating linkage type cab suspension to facilitate ride comfort. Fully floating cab has certain limitations in terms of stability of cab in dynamic articulations during vehicle running especially in off-road terrain applications. Presence on linkages leads to more wear and tear of joints and bushes which will in turn provide detrimental effect on vibration levels of cab that affects ride comfort for occupants. There is a dire need to develop a system that provides improvement in lateral and vertical stability of cab without compromising ride comfort of occupants. Durability of the product also to be met till life of vehicle. Anti-Vibration Stability Cab Mount is an unsymmetrical mount designed by compounding of elastomeric(rubber) metal bonded outer sleeves sandwiched between multistage inner mount bonded on aluminum casing. Cabin front supports are hinged to mount along with housing providing proper alignment to cab after assembly.

Overall cycle time and prototype testing are significantly decreased by assessment of cooling module performance in the design stage itself. Hence, Front End Cooling and Thermal Management are essential components of the vehicle design process. Performance of the cooling module depends upon a variety of factors like frontal opening, air flow, under-hood sub-systems, module positioning, front grill design, fan operation. Effects of design modifications on the engine cooling performance are quantified by utilizing computational fluid dynamics (CFD) tool FluentTM. Vehicle frontal configuration is captured in the FE model considering cabin, cargo and underbody components. Heat Exchanger module is modelled as a porous medium to simulate the fluid flow. Performance data for the Heat Exchanger module is generated using the 1D KuliTM software. In this paper, CFD simulation of Front End Cooling is performed for maximum torque and maximum power operating conditions.

Vehicle life and performance is affected by many factors when in use. The most influential being the vibrations generated especially when the vehicle is in motion. These vibrations are directly experienced by the driver, whose performance goes down, if under continuous influence of these vibrations. This increases the fatigue and greatly reduces the return on investment done by the customer. There are two major sources of vibrations, the engine and the road on which the vehicle moves. To prevent such issues engine mounts are used in vehicles, which may seem simple but perform a critical role, of providing comfort to the driver. Therefore, it becomes important that thoroughly designed and examined mounts are being used in the vehicle. This paper focuses on the methodology to be followed for design and validation of an engine mount used in heavy duty vehicles.

Seats are one of the critical component of school bus for children’s comfort & safety. Seat foam thickness, its shape, cushion width & seat height will play a vital role in comfort. Fatigue is the common cause due to uncomfortable seating and it is due to only one type of seat available in school buses to accommodate different height children. (here different height means; schools have children from class nursery to senior secondary). Fatigue will cause impact on children’s health & overall development. The topic was chosen because of increasing concerns in children’s comfort & safety in school buses. In existing design, standard seat with cushion height from bus floor is 450mm. In this case, it’s only suitable for children height of 4.5 feet to 5.5 feet. Ergonomically, it is very difficult to climb on the seat for range of children height from 3 feet to 4feet.