Search Results

The automotive trends of vehicles with lower aerodynamic drag and more powerful drivetrains have caused increasing concern regarding stability issues at high speeds, since more streamlined bodies show greater sensitivity to crosswinds. This is especially pronounced for high vehicles, such as sports utility vehicles. Besides, the competitiveness in the automotive industry requires faster development times and, thus, a need to evaluate the high speed stability performance in an early design phase, preferable using simulation tools. The usefulness of these simulation tools partly relies on realistic boundary conditions for the wind and quantitative measures for assessing stability without the subjective evaluation of experienced drivers. This study employs an on-road experimental measurements setup to define relevant wind conditions and to find an objective methodology to evaluate high speed stability.

Partially-Averaged Navier-Stokes Simulations (PANS) were made of flow around a generic vehicle influenced by side wind at four different yaw angles to investigate the prediction capabilities of PANS. Comparisons with results of LES show clear advantages of PANS in predicting pressure-induced separation resulting in the trailing vortices aligned with the direction of the flow. Poorer agreement was obtained in the near wake when the boundary layer separates at the end of the surface at the rear end. A possible explanation for the lack of accuracy at the rear end of the body was found in the formulation of the switching coefficient fk which produces too low values resulting in too low eddy viscosity in this region.

Semi-active suspension systems for ground vehicles have been the focus of research for several years as they offer improvements in vehicle comfort and handling. This kind of suspension has attracted more interest compared to active suspension systems especially due to lower cost and energy consumption. In this paper the capabilities of a semi-active front axle suspension are investigated for a commercial vehicle. A half-truck model of a 4x2 tractor and semitrailer combination is developed in Matlab/Simulink for this purpose. Also, a 2 DOF roll plane model is considered to capture the roll motion of the vehicle body mass. Employing the above-mentioned models, results from on-off and continuous variable semi-active damping systems are compared to the ones from the passive suspension system according to ride comfort and handling safety characteristics.

The new corner-based architecture of electrified road vehicles requires a redesign of vehicle suspension components. The design protocol must satisfy the target parameters derived from dynamics requirements. The roll stiffness of the anti-roll bar is a crucial parameter for the handling performance of a vehicle. During the development of a new suspension, the design of the anti-roll bar needs to be modified. To this aim, two-dimensional beam theory models can quickly provide a preliminary design of this component. However, the simplified models might be inaccurate due to the three-dimensional and complex shapes of the bars. The present study aims to overcome this limitation. An analytical beam model based on the spline description of the bar has been developed, which is accurate even for complex geometries of the bars. Assuming a hollow and closed circular cross-section, the model returns the average diameter and the radial thickness needed to achieve the stiffness performance.

Under a global impulse for less man-made emissions, the automotive manufacturers search for innovative methods to reduce the fuel consumption and hence the CO2-emissions. Aerodynamics has great potential to aid the emission reduction since aerodynamic drag is an important parameter in the overall driving resistance force. As vehicles are considered bluff bodies, the main drag source is pressure drag, caused by the difference between front and rear pressure. Therefore increasing the base pressure is a key parameter to reduce the aerodynamic drag. From previous research on small-scale and full-scale vehicles, rear-end extensions are known to have a positive effect on the base pressure, enhancing pressure recovery and reducing the wake area. This paper investigates the effect of several parameters of these extensions on the forces, on the surface pressures of an SUV in the Volvo Cars Aerodynamic Wind Tunnel and compares them with numerical results.

Previous research on both small-scale and full-scale vehicles shows that base extensions are an effective method to increase the base pressure, enhancing pressure recovery and reducing the wake size. These extensions decrease drag at zero yaw, but show an even larger improvement at small yaw angles. In this paper, rear extensions are investigated on an SUV in the Volvo Cars Aerodynamic Wind Tunnel with focus on the wake flow and on the unsteady behavior of the surface pressures near the base perimeter. To increase the effect of the extensions on the wake flow, the investigated configurations have a closed upper- and lower grille (closed-cooling) and the underbody has been smoothed with additional panels. This paper aims to analyze differences in flow characteristics on the wake of an SUV at 0° and 2.5° yaw, caused by different sets of extensions attached to the base perimeter. Extensions with several lengths are investigated with and without a kick.

The presented paper is dedicated to the driving comfort evaluation in the case of the electric vehicle architecture with four independent wheel corners equipped with in-wheel motors (IWMs). The analysis of recent design trends for electrified road vehicles indicates that a higher degree of integration between powertrain and chassis and the shift towards a corner-based architecture promises improved energy efficiency and safety performances. However, an in-wheel-mounted electric motor noticeable increases unsprung vehicle mass, leading to some undesirable impact on chassis loads and driving comfort. As a countermeasure, a possible solution lies in integrated active corner systems, which are not limited by traditional active suspension, steer-by-wire and brake-by-wire actuators. However, it can also include actuators influencing the wheel positioning through the active camber and toe angle control.

The emergence of new electric vehicle (EV) corner concepts with in-wheel motors offers numerous opportunities to improve handling, comfort, and stability. This study investigates the potential of controlling the vehicle's corner positioning by changing wheel toe and camber angles. A high-fidelity simulation environment was used to evaluate the proposed solution. The effects of the placement of the corresponding actuators and the actuation point on the force required during cornering were investigated. The results demonstrate that the toe angle, compared to the camber angle, offers more effect for improving the vehicle dynamics. The developed direct yaw rate control with four toe actuators improves stability, has a positive effect on comfort, and contributes to the development of new active corner architectures for electric and automated vehicles.