Search Results

In this paper, an analytical procedure for prediction of shell radiated noise of air induction systems (AIS) due to engine acoustic excitation, without a prototype and physical measurement, is presented. A set of modeling and simulation techniques are introduced to address the challenges to the analytical radiated noise prediction of AIS products. A filter seal model is developed to simulate the unique nonlinear stiffness and damping properties of air cleaner boxes. A finite element model (FEM) of the AIS assembly is established by incorporating the AIS structure, the proposed filter seal model and its acoustic cavity model. The coupled acoustic-structural FEM of the AIS assembly is then employed to compute the velocity frequency response of the AIS structure with respect to the air-borne acoustic excitations.

This paper describes a front road wheel steer-by-wire system with two actuator motors on the rack and pinion assembly to move the road wheels. Dual actuators are used to provide actuator redundancy and to enhance the fault tolerance capability. When one actuator faults or fails, the other actuator is designed to work independently and maintain full system performance. The paper emphasizes control method to implement the motion control for the front road wheel steer-by-wire system with two actuators on the common load. The proposed dual servo synchronization motion control implements the angle tracking for the road wheel reference input by controlling two actuators synchronously and cooperatively. It includes two servo feedback control loops to track the common reference input. The angular position error between two feedback loops is compensated using a synchronized compensator.

The traditional method of engine knock detection is to compare the knock intensity with a predetermined threshold. The calibration of this threshold is complex and difficult. A statistical knock detection method is proposed in this paper to reduce the effort of calibration. This method dynamically calculates the knock threshold to determine the knock event. Theoretically, this method will not only adapt to different fuels but also cope with engine aging and engine-to-engine variation without re-calibration. This method is demonstrated by modeling and evaluation using real-time engine dynamometer test data.

As global automobile manufacturers prepare for the phase-out of R134a in Europe, they must address the issue of using the new refrigerant for European sales only or launching the product worldwide. Several factors play into this decision, including cost, service, risk, customer satisfaction, capacity, efficiency, etc. This research effort addresses the minimal vehicle-level hardware differences necessary to provide a European solution of R1234yf while continuing to install R134a into vehicles for the rest of the world. It is anticipated that the same compressor, lubricant and condenser; most fluid transport lines; and in most cases the evaporator can be common between the two systems.

This paper describes two studies; each conducted concurrently in North America and Europe to assess subjective impressions and simulated driving task performance using a touch screen interface with different types of auditory and haptic feedback. The first study investigated subjective impressions of four types of touch screen feedback in a static laboratory setting. The second study investigated the influence of the same four touch screen feedback types on simulated driving task performance using the lane change test (LCT). Results of the first study revealed significant similarities and differences in subjective impressions between respondents in each of the two regions studied. Results of the second study revealed differences in task performance that suggest distinct participant strategies in each of the two regions studied.

In Brazil the market for plastic parts molds, in last few years had become very competitive, with several Vehicle Operations and a big number of a different models, and with today total market volume it means low volumes productions for each model. This market demands for good toolshops and at the same time a big pressure to reduce investments, one of the most important. Plastic components usage in the car, is increasing overtime, with new applications for Exterior, interior and powertrain, requiring new technologies for Injection molding processing and making molds to be more complex. The development of plastic parts in Brazil has its own characteristics, strengths and weaknesses. In fact a big and heterogeneous market. This paper intends to present an analysis of development of plastic parts in Brazil, considering the development of mold tooling locally, focusing the automotive market.

In the absence of prototypes, analytical methods such as finite element analysis are very useful in resolving noise and vibration problems, by predicting dynamic behavior of the automotive components and systems. Finite Element Analysis (FEA) is a simulation technique and involves making assumptions that affect analytical results. Acceptance and use of these results is greatly enhanced through test validation. In this paper, dynamic behavior of the automotive propshaft equipped with cardboard liner and torsional damper is investigated. The finite element model is validated at both component and subsystem levels using frequency response functions. Effects of the cardboard liner and torsional damper on the propshaft bending, torsional and breathing frequencies are studied under free-free boundary conditions. Effects of the U-Joint stiffness along with other design variables on the driveshaft dynamic behavior are also studied.

The fundamentals of multi-leaf spring design as determined through beam theory offers a general perspective on how finite element analysis works. Additionally, the fundamentals of combining dissimilar materials require a basic knowledge of how the combined equivalent modulus affects the overall stiffness characteristics of multi-leaf design. By capturing these basic fundamentals into finite element modeling, an analysis of a steel-composite multi-leaf contact model relative to an idealized steel-composite multi-leaf model shows the importance of contact modeling. The results demonstrate the important differences between an idealized non-contact model relative to a complete contact model.

The starter drive clutch is a one way roller clutch and a key component in a starter motor that is used to crank internal combustion engines. The starter drive clutch transmits torque from an electrical motor to a ring gear mounted on a cranking shaft in an engine thus cranks the engine. The clutch also prevents the whole starter from damage caused by extremely high load and/or extremely high speed applied to the starter pinion from the engine. Drive slippage and barrel cracking are two major failure modes for the starter drive[1]. Insufficient torque capacity results in drive slippage while excessive high hoop stress on the clutch barrel ring causes barrel crack. To eliminate drive slippage failure, the clutch should be designed with high torque capacity. High torque capacity, however, is a cause of high hoop stress on the barrel that may result in the cracked barrel failure. Higher torque capacity and lower hoop stress are two completely opposite design directions.

This paper discusses our experiences on the implementation and benefits of using the Hardware-In-the-Loop (HIL) systems for Powertrain control system software verification and validation. The Visteon HIL system integrated with several off-the-shelf diagnostics and calibration tools is briefly explained. Further, discussions on test automation sequence control and failure insertion are outlined The capabilities and advantages of using HIL for unit level software testing, open loop and closed-loop system testing, fault insertion and test automation are described. HIL also facilitates Software and Hardware Interface validation testing with low-level driver and platform software. This paper attempts to show the experiences with and capabilities of these HIL systems.

This paper discusses the development of combination vehicle stability program (CVSP) at Visteon. It will describe why stability control is needed for combination vehicles and how the vehicle stability can be improved. We propose and evaluate controller structures and design methods for CVSP. These include driver's intent identification, combination vehicle status estimation and control, and fault detection / tolerance. In this paper, the braking and steering dynamics of car-trailer and tractor-semitrailer combinations, and the brake systems which should be used extensively to increase the stability of combination vehicles are presented. Also our development platform is introduced and the combination vehicle simulation results are presented. The definition of combination vehicles in this paper includes car-trailer and commercial tractor-semitrailer combinations since their vehicle dynamics are based on the same equations of motion.

This paper presents an unambiguous and intuitive method for identification of steering column resonant (SCR) mode of vibration. One simple but overlooked technique to determine the SCR mode in-vehicle is to provide local stiffnesses of the body locations where the Instrument Panel (IP) attaches, to the IP suppliers to be used in their design and development. This paper describes how this technique is useful in predicting the first few important in-vehicle steering column modes for different classes of vehicles, with examples presented in each class. The results obtained from such analyses are compared against those from direct in-buck simulations. This technique is not limited to its application in developing IP systems, but can easily be extended to include other systems such as seats, fuel tanks, etc. Also it is shown that a design optimization analysis may be performed using these attachment stiffnesses as design variables resulting in a system level solution.

Interior compartment doors are required by Federal Motor Vehicle Safety Standard (FMVSS) 201, to stay closed during physical head impact testing, and when subjected to specific inertia loads. This paper defines interior compartment doors, and shows examples of several different latches designed to keep these doors closed. It also explores the details of the requirements that interior compartment doors and their latches must meet, including differing requirements from automobile manufacturers. It then shows the conventional static method a supplier uses to analyze a latch and door system. And, since static calculations can't always capture the complexities of a dynamic event, this paper also presents a case study of one particular latch and door system showing a way to simulate the forces experienced by a latch. The dynamic simulation is done using Finite Element Analysis and instrumentation of actual hardware in physical tests.

Visteon has developed a CAE procedure to qualify instrument panel (IP) products under the vehicle key life test environments, by employing a set of CAE simulation and durability techniques. The virtual key life test method simulates the same structural configuration and the proving ground road loads as in the physical test. A representative dynamic road load profile model is constructed based on the vehicle proving ground field data. The dynamic stress simulation is realized by employing the finite element transient analysis. The durability evaluation is based on the dynamic stress results and the material fatigue properties of each component. The procedure has helped the IP engineering team to identify and correct potential durability problems at earlier design stage without a prototype. It has shown that the CAE virtual key life test procedure provides a way to speed up IP product development, to minimize prototypes and costs.

Low resolution fractional factorial experimental designs, used in screening, are more popular than ever due to the ever increasing costs of materials and machine time. Experimenters have to be more precise in their analysis, making every degree of freedom count. Resolution III designs are becoming more commonplace for use in screening designs. When running unsaturated resolution III designs there are extra degrees of freedom stemming from unassigned interactions. It is common practice to utilize these extra degrees of freedom to approximate error. In many cases, this common practice can over state the error and lead to erroneous results regarding factor statistical significance. Utilizing saturated resolution III designs and statistically analyzing unassigned interactions while estimating the error with replication is a method for strengthening the DOE strategy and improving the results from screening designs.

There is still much controversy and confusion in industry today regarding the use of process capability indices and analysis. A lack of knowledge regarding the underlying variation assumptions and rationale sampling strategies in indices such as Cp, Cpk, Pp and Ppk have added to the confusion and in many cases has led to misapplication of these widely used metrics. This issue has also promoted inconsistency in the assessment of long-term versus short-term capability and has hampered the true characterization of processes which is a critical step in any continuous improvement effort. Capability indices and analysis, when properly applied can impart a wealth of knowledge regarding process performance as well as provide focus for improvement activity through the proper characterization and enumeration of variation. Being able to properly characterize variation if the first step in reducing it.

Environmental concerns and changes in regulations around the world are turning mass-production electric vehicles (EVs) a reality. While the average driver is very familiar with the instruments available for the current internal combustion engine vehicles (ICEVs), the same does not hold for EVs. They require unique gages and tell-tales (also known as warning lights), tailored to their architecture, operating modes and intended use. This paper makes a comparison of the instruments used in ICEVs and EVs, suggesting a minimum set and standardization of the associated symbols.

Realizing the value of knowledge, corporations are turning to Knowledge Based Engineering (KBE) as a design process. A fuel rail KBE tool was created at Visteon with the purpose of increasing knowledge retention and delivering knowledge based designs to the customer much quicker than with conventional methods. Currently, both engineers and CAD designers are using the Fuel Rail KBE Modeler at Visteon. It has been used on many vehicle programs and has saved the company countless person-hours of development time. The Fuel Rail KBE Modeler is a powerful tool that saves resources through automation of both the design and analysis processes. This paper documents the incorporation of automated FEA capability into the KBE environment.

A new risk management method, the System Integrated Life Cycle Risk Management Methodology (SILC RMM), is based on systems engineering principles and is compatible with current standards. The SILC method, created by automotive engineers, addresses shortcomings with FMEA and other risk management (RM) methods, and integrates the FMEA and risk management functions into day-to-day engineering project activities. The SILC approach accommodates technology, cost, schedule, environmental and safety risks throughout the systems engineering project life cycle - from conception to recycle. It allows direct integration of RM information with system and project information for more efficient and effective utilization of resources and optimal overall risk management.

Composite materials can be used effectively for structural applications where high strength-to-weight and stiffness-to-weight ratios are required. Although the design and analysis techniques for static, buckling and vibration loadings are fairly well established, methodologies for analysis of composite structures under impact loading are still a major research activity. This paper presents a nonlinear finite-element analysis method to analyze a composite structure subjected to axial impact load. The analysis was performed using MSC/DYTRAN FE code while pre and post processing were done using MSC/PATRAN program. In addition, a steel tube of the same geometry was analyzed for comparison purpose.