Search Results

The objective of this research is to investigate the effect of the blast load on the vehicle and occupant and identify the sensitivity of the vehicle parameters to the blast load, therefore figure out the design solution to protect the vehicle and occupant. CAE explicit commercial code, LSDYNA, is applied in this research with adopting CONWEP method for the blast load. The LSDYNA 95th percentile Hybrid III dummy model is used for occupant simulation. Seat, seat belt, and underbody and underbody armor are interested areas in the design to meet the survivability and weight target. The results show the protection can be effectively achieved through employing the new design method in three areas mentioned above.

The feasibility of using ultra low sulfur diesel (ULSD), synthetic paraffinic kerosene (S-8), military grade jet fuel (JP-8) and commercial B20 blend (20% v biodiesel in ULSD) in a power generator equipped with a compression ignition (CI) engine was investigated according to the MIL-STD-705C military specifications for engine-driven generator sets. Several properties of these fuels such as cetane number, lubricity, viscosity, cold flow properties, heat of combustion, distillation temperatures, and flash point, were evaluated. All fuels were tested for 240 hours at a stationary load of 30 kW (60% of full load) with no alteration to the engine calibrations. The brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), frequency, and power of the generator using S-8, JP-8 and B20 were compared with the baseline fuel ULSD.

This paper aims to develop some enhanced identification algorithms for real time characterization of battery dynamics. The core of such a system is advanced system identification techniques that provide fast tracking capability to update battery cell's individual models in real-time operation. Due to inevitable measurement noises on voltage and current observations, the identification algorithms must perform under both input and output noises, leading to more challenging issues than standard identification problems. It is shown that typical battery models may not be identifiable, unique battery model features require modified input/output expressions, and standard least-squares identification methods will encounter identification bias. This paper devises modified model structure and algorithms to resolve these issues. System identifiabihty, algorithm convergence, identification bias, and bias correction mechanisms are established.

The Ultrasonic Collision Avoidance System is designed to eliminate collisions when cars, trucks, and other vehicles are backing up. Many backup collisions result when objects are not in view or when a driver underestimates the distance to the object. The Ultrasonic Proximity System warns the driver of objects in the path and displays the distance to the object. The distance to an object is represented by a 10 segment light emitting diode (LED) bar graph. If all LED's are off, the object is more than 10 feet away. The first LED will illuminate at approximately 10 feet, and as the vehicle moves closer to the obstruction more LED's illuminate, about 1 LED per foot. If the object is closer than 1′-6″, the last LED will illuminate and an audible alarm will sound.

Injuries to the thorax and abdomen comprise a significant percentage of all occupant injuries in motor vehicle accidents. While the percentage of internal chest injuries is reduced for restrained front-seat occupants in frontal crashes, serious skeletal chest injuries and abdominal injuries can still result from interaction with steering wheels and restraint systems. This paper describes the design and performance of prototype components for the chest, abdomen, spine, and shoulders of the Hybrid III dummy that are under development to improve the capability of the Hybrid III frontal crash dummy with regard to restraint-system interaction and injury-sensing capability.

There are many mechanisms for ankle injury to front seat occupants involved in automotive impacts. This study addresses injuries to the ankle joint involving inversion or eversion, in particular at high rates of loading such as might occur in automotive accidents. Injuries included unilateral malleolar fractures and ligament tears, and talus and calcaneous avulsions. Twenty tests have been performed so far, two of them using Hybrid III lower leg and the rest using cadaveric specimens. The specimens were loaded dynamically on the bottom of the foot via a pneumatic cylinder in either an inversion or eversion direction at fixed dorsiflexion and plantarflexion angles. The applied force and accelerations have been measured as well as all the reaction forces and moments. High-speed film was used to obtain the inversiordeversion angle of the foot relative to the tibia and for following ligament stretch.

An experimental study was carried out to characterize the spray atomization process of automotive port fuel injectors retrofitted to a novel pressure modulation piezoelectric driver, which generates a pressure perturbation inside the fuel line. Unlike many other piezoelectric atomizers, this unit does not drive the nozzle directly. It has a small size and can be installed easily between regular port injector and fuel lines. There is no extra control difficulty with this system since the fuel injection rate and injection timing are controlled by the original fuel-metering valve. The global spray structures were characterized using the planar laser Mie scattering (PLMS) technique and the spray atomization processes were quantified using phase Doppler anemometry (PDA) technique.

A humerus provisional reference value (PRV) based on human surrogate data was developed to help evaluate upper arm injury potential. The proposed PRV is based on humerus bone bending moments generated by testing pairs of cadaver arms to fracture in three-point bending on an Instron testing machine in either lateral-medial (L-M) or anterior-posterior (A-P) loading, at 218 mm/s and 0.635 mm/s loading rates. The results were then normalized and scaled to 50th and 5th percentile sized occupants. The normalized average L-M bending moment at failure test result was 6 percent more than the normalized average A-P bending moment. The normalized average L-M shear force at failure was 23 percent higher than the normalized average A-P shear force. The faster rate of loading resulted in a higher average bending moment overall - 8 percent in the L-M and 14 percent in the A-P loading directions.

Drivers' eye location data was collected in three vehicle (Vega, 1973 Buick, and Chevrolet Van) and in three environments (laboratory buck, static and on-the-road) for each vehicle type. In each environment data was collected for 50 subjects who were stratified by height and sex. A specially constructed remote coordinate system in connection with T.V. cameras was used for data collection. Drivers' eye locations were found to vary as a function of vehicle type. For the Buick and Van there were differences between data collected in the laboratory buck and on-the-road. There were no differences in data collected in the static environment and on-the-road for any vehicle type.

Reduced basis techniques and the method of mode-acceleration are applied to transient analysis of simple beam and truss structures. It is noted that the method of mode-acceleration effectively recovers the first Ritz vector used in Ritz procedures. The theoretical basis for Lanczos algorithms that generate Ritz vectors is explained. Both mode-acceleration and Ritz procedures are found, generally, to be more accurate than mode-displacement in calculation of transient shear stresses, moments and normal stresses. Reanalysis using Ritz vectors is discussed following Kitis and Pilkey [9] and Noor and Lowder [10].

This paper focuses on the role and significance of linear momentum and kinetic energy in controlling air bags aboard vehicles. Among the results of the study are analytic and geometric models that characterize crash behavior and control algorithms that quantify crash severity and identify crash configurations. These results constitute an effective basis for crash-data design and air-bag control.

The Indicated Mean Effective Pressure (IMEP) is a very important engine parameter, giving significant information about the quality of the cycle that transforms heat into mechanical work. For this reason, modern data acquisition systems display, on line, the cylinder pressure variation together with the corresponding IMEP. The paper presents a very simple algorithm for the calculation of IMEP, based on the correlation between IMEP and the gas pressure torque. It was found that that the IMEP may be calculated by a very simple formula involving only two harmonic components of the cylinder pressure variation. The computation of the two harmonic components is very easily performed because it does not involve the calculation of an average pressure and the cylinder volume variation. The method was experimentally validated showing differences less than 0.2% with respect to the IMEP calculated by the traditional method.

Numerical analyses of head and neck response during side impact are presented in this paper. A mathematical human model for side impact simulation was developed based on previous studies of other researchers. The effects of muscular activities during severe side impact were analyzed with the use of this model. This study shows that the effect of muscular activities is significant especially if the occupant is prepared to resist the impact. This result suggests that the modeling of muscles is important for the simulation of real accident situation.

A high carbon, high silicon and high manganese steel containing about 1% carbon, 3.0% silicon and 2.0% manganese has been developed. This steel has been synthesized using the concepts from Austempered Ductile Cast Iron (ADI) technology. The influence of austempering process on the microstructure and the room temperature mechanical properties of this steel was investigated. The influence of microstructure on the plain strain fracture toughness of this new steel was also examined. Four batches of compact tension and cylindrical tensile samples were prepared from this steel as per ASTM standards E-399 and E-8 respectively. Two batches of specimens were processed by traditional quenching and tempering process while other two batches were austempered. The microstructures were characterized by X-ray diffraction and optical metallography.

Seventeen Heidelberg type cadaveric side impact sled tests, two sled-to-sled tests, and forty-four pendulum tests have been conducted at Wayne State University, to determine human responses and tolerances in lateral collisions. This paper describes the development of a simplified finite element model of a human occupant in a side impact configuration to simulate those cadaveric experiments. The twelve ribs were modeled by shell elements. The visceral contents were modeled as an elastic solid accompanied by an array of discrete dampers. Bone condition factors were obtained after autopsy to provide material properties for the model. The major parameters used for comparison are contact forces at the level of shoulder, thorax, abdomen and pelvis, lateral accelerations of ribs 4 and 8 and of T12, thoracic compression and injury functions V*C, TTI and ASA.

As early as the 1950's, Gurdjian and colleagues (Gurdjian et al., 1955) observed that brain injuries could occur by direct pressure loading without any global head accelerations. This pressure-induced injury mechanism was "forgotten" for some time and is being rekindled due to the many mild traumatic brain injuries attributed to blast overpressure. The aim of the current study was to develop a finite element (FE) model to predict the biomechanical response of rat brain under a shock tube environment. The rat head model, including more than 530,000 hexahedral elements with a typical element size of 100 to 300 microns was developed based on a previous rat brain model for simulating a blunt controlled cortical impact. An FE model, which represents gas flow in a 0.305-m diameter shock tube, was formulated to provide input (incident) blast overpressures to the rat model. It used an Eulerian approach and the predicted pressures were verified with experimental data.