Search Results

The post-flame oxidation of unburned hydrocarbons released from the ring-pack crevice was investigated for a small, air-cooled, spark-ignition utility engine. Spark timing sweeps were performed at 50, 75 and 100% load and speeds of 1800, 2400 and 3060 RPM while operating at a 12:1 air-fuel ratio, which is typical for these engines. A global HC consumption rate (GCR) was introduced based on the temporal profile of the mass released from the ring pack; the mass release after CA90 and up to the point where the remainder of the ring pack HC mass is equal to the exhaust HC level was taken as the mass oxidized, and a rate was defined based on this mass and the corresponding crank angle period over which this took place. For all conditions tested, the GCR varied with the spark timing; advanced spark timing gave higher GCR.

High resolution planar laser-induced fluorescence (PLIF) measurements were performed in an optically accessible internal combustion (IC) engine to investigate the behavior of scalar dissipation and the fine-scale structures of the turbulent scalar field. The fluorescent tracer fluorobenzene was doped into one of the two intake streams and nitrogen was used as the carrier gas to permit high signal-to-noise ratio fluorescence measurements without oxygen quenching effects. The resulting two-dimensional images allowed for an analysis of the structural detail of the scalar and scalar dissipation fields defined by the mixing of the two adjacent intake streams. High levels of scalar dissipation were found to be located within convoluted, sheet-like structures in accordance with previous studies. The fluorescence data, which were acquired during the intake stroke, were also used to examine the scalar energy and dissipation spectra.

The effects of augmented mixing through the use of an auxiliary gas injection (AGI) were investigated in a direct-injection gasoline engine operated at a 22:1 overall air-fuel ratio, but with retarded injection timing such that the combustion was occurring in a locally rich mixture as evident by the elevated CO emissions. Two AGI gas compositions, nitrogen and air, were utilized, the gas supply temperature was ambient, and a wide range of AGI timings were investigated. The injected mass was less than 10% of the total chamber mass. The injection of nitrogen during the latter portion of the heat release phase resulted in a 25% reduction in the CO emissions. This reduction is considered to be the result of the increased mixing rate of the rich combustion products with the available excess air during a time when the temperatures are high enough to promote rapid oxidation.

Cycle-to-cycle variation in combustion phasing and combustion rate cause knock to occur differently in every cycle. This is found to be true even if the end gas thermo-chemical time history is the same. Three cycles are shown that have matched combustion phasing, combustion rate, and time of knock onset, but have knock intensity that differs by a factor of six. Thus, the prediction of knock intensity must include a stochastic component. It is shown that there is a relationship between the maximum possible knock intensity and the unburned fuel energy at the time of knock onset. Further, for a small window of unburned energy at knock onset, the probability density function of knock intensity is self similar when scaled by the 95th percentile of the cumulative distribution, and log-normal in shape.

Fuel film temperature and thickness were measured on the piston crown of a DISI engine under both motored and fired conditions using the fiber-based laser-induced fluorescence method wherein a single fiber delivers the excitation light and collects the fluorescence. The fibers were installed in the piston crown of a Bowditch-type optical engine and exited via the mirror passage. The fuel used for the fuel film temperature measurement was a 2×10-6 M solution of BTBP in isooctane. The ratio of the fluorescence intensity at 515 to that at 532 nm was found to be directly, but not linearly, related to temperature when excited at 488 nm. Effects related to the solvent, solution aging and bleaching were investigated. The measured fuel film temperature was found to closely follow the piston crown metal temperature, which was measured with a thermocouple.

High-resolution planar laser-induced fluorescence (PLIF) measurements were performed on the scalar field in an optical engine. The measurements were of sufficient resolution to fully resolve all of the length scales of the flow field through the full cycle. The scalar dissipation spectrum was calculated, and by fitting the results to a model turbulent spectrum the Batchelor scale of the turbulent flow was estimated. The scalar inhomogeneity was introduced by a low-momentum gas jet injection. A consistent trend was observed in all data; the Batchelor scale showed a minimum value at top dead center (TDC) and was nearly symmetric about TDC. Increasing the engine speed resulted in a decrease of the Batchelor scale, and the presence of a shroud on the intake valve, which increased the turbulence intensity, also reduced the Batchelor scale. The effect of the shrouded valve was less significant compared to the effect of engine speed.

Valve deactivation followed by multiple compression-expansion strokes was employed to remove intake-generated turbulence from the bulk gas in an internal combustion engine. The result was a nearly quiescent flowfield that retains the same time-varying geometry and, to a first approximation, thermodynamic conditions as a standard engine. Mass loss, and more significantly heat loss were found to contribute to a reduction in the peak cylinder pressure in the cycle following two compression-expansion strokes. The reduction of the turbulence was verified both computationally and by performing premixed combustion studies. Mixing studies of both liquid spray jets and gaseous jets were performed. Laser-induced fluorescence images of high spatial resolution and signal-to-noise ratio were acquired, allowing the calculation of the two in-plane components of the scalar dissipation rate.

In-cylinder thermal barrier coatings (TBCs) have the capability to reduce fuel consumption by reducing wall heat transfer and to increase exhaust enthalpy. Low thermal conductivity, low volumetric heat capacity thermal barrier coatings tend to reduce the gas-wall temperature difference, the driving potential for heat transfer from the gas to the combustion chamber surfaces. This paper presents a coupling between an analytical methodology for multi-layer coated wall surface temperature prediction with a fully calibrated production model in a commercial system-level simulation software package (GT-Power). The wall surface temperature at each time step was calculated efficiently by convolving the engine wall response function with the time-varying surface boundary condition, i. e., in-cylinder heat flux and coolant temperature. This tool allows the wall to be treated either as spatially uniform with one set of properties, or with independent head/piston/liner components.

Bulk gas temperature in an HCCI engine was measured using a novel optical sensing technique. A wavelength-agile absorption sensor using a fiber-coupled LED was used to measure the in-cylinder gas temperature. H2O absorption spectra spanning 1380-1420nm were recorded once every 63 μs using this sensor. The gas temperature was inferred from a least-squares fit of the integrated absorbance areas of H2O absorption features in this spectral region to those from simulated spectra. The primary source of the H2O was the humidity in the intake air. Measurements were made during the compression and early portion of the combustion phase of an n-heptane fueled HCCI engine. The measured pressure-temperature history was compared to kinetic calculations of the ignition delay, and showed the traversal of the negative temperature coefficient regime.

Thermal swing coatings that have low volumetric heat capacity and low thermal conductivity are attractive because they have the potential to significantly reduce heat transfer to the combustion chamber walls. This paper presents an analytical method for determining the exact solution of the time-resolved wall temperature during the engine cycle for any number of coating layers and properties using the Laplace transformed heat diffusion equation. The method relies only on material properties and the past heat flux history, and represents the exact solution of the heat diffusion equation. The analytical nature of the solution enables fast computation and, therefore, application to system-level optimization calculations. The model relies on an assumption of one-dimensional heat flow, and constant material properties.