Search Results

This paper describes an experimental study on the performance of self-piercing riveted (SPR) joints and adhesively bonded SPR joints connecting steel and aluminum components under both quasi-static and cyclic loading. The joint configurations cover a wide range of material gauges, types and grades. Two and three thickness joints, with and without adhesive are also part of this study. Load versus deflection behavior, load carrying capacity, fatigue life and the failure modes for each type of joint are discussed. This study focuses on the influence of dissimilar material and adhesives to the joint performance.

This paper describes a study on identifying a suitable thickness for finite element modeling a “deformable washer” to simulate bolted joints for vehicle level durability analysis based on experimental results. First, a test matrix table is introduced, which is based on representative vehicle structures for different bolt/nut sizes, bolt grades, sheet gages, and sheet materials etc. Then coupon tests, both static and fatigue, are illustrated. Next, the corresponding finite element model with different thickness of “deformable washers” and results are presented. Following that, the optimal “deformable washer” thickness is recommended based on statistical parameters (mean and standard deviation) of the relative differences between finite element analysis results and physical test results. Lastly, a case study is demonstrated for the proposed strategy.

In this paper, the methodology of finite element analyses of fastened joints in automotive engineering applications is described in detail. The analyses cover a) the possibility of slippage of the spacer with the design/actual clamp load, and under critical operating loads; b) the strength of the fastener and other structural components comprising the joint under the maximum clamp load. The types of fastened joints, the mechanical characteristics of the joints, the relationship of clamp load to torque, the design and maximum clamp loads, the finite element model meshing and assembly, the non-linearity due to contact, the determination of gaps and stack-up, and the nonlinear material simulation and loading procedures are described. An analysis example of a fastened joint on chassis is also illustrated.

In this paper, mechanism of fastened joints is described; numerical analyses and testing calibrations are conducted for the possible simplified finite element simulation approaches of the joints; and the best simplified approach is recommended. The approaches cover variations of element types and different ways that the joints are connected. The element types include rigid elements, deformable bar elements, solid elements, shell elements and combinations of these element types. The different ways that the joints are connected include connections of one row of nodes, two row of nodes and alternate nodes in the first and second rows. These simplified simulation approaches are numerically evaluated on a joint of two plates connected by a single fastener. The fundamental loads, bending with shear, shear and tension are applied in the numerical analyses. A detailed model including contact and clamp load are analyzed simultaneously to provide “accurate results”.

This paper describes a new procedure for more accurate durability predictions of stress along edges of automotive body structures. The current elemental stress based CAE procedures often require iterative mesh refinement to correlate predictions to experimental cracking on the edges of components. The new proposed procedure is based on element nodal stress. It is first studied on a circular hole representing a notch in a rectangular plate with different element sizes and options. Elemental nodal stress demonstrates an improvement over elemental stress methods by correlating with theoretical notch stress result. The proposed procedure is then studied on multiple examples of experimental cracks and successfully predicts issues where the current elemental stress method does not. In addition, it avoids the iterative mesh refinement associated with the current methods.

In this paper, four possible CAE analysis methods for calculating critical buckling load and post-buckling permanent deformation after unloading for geometry imperfection sensitive thin shell structures under uniformly distributed loads have been investigated. The typical application is a vehicle roof panel under snow load. The methods include 1) nonlinear static stress analysis, 2) linear Eigen value buckling analysis 3) nonlinear static stress analysis using Riks method with consideration of imperfections, and 4) implicit quasi-static nonlinear stress analysis with consideration of imperfections. Advantage and disadvantage of each method have been discussed. Correlations between each of the method to a physical test are also conducted. Finally, the implicit quasi-static nonlinear stress analysis with consideration of geometry imperfections that are scaled mode shapes from linear Eigen value buckling analysis is preferred.

This paper discusses CAE simulation methods to predict the thermal induced buckling issues when vehicle body panels are subjected to the elevated temperature in e-coat oven. Both linear buckling analysis and implicit quasi-static analysis are discussed and studied using a quarter cylinder shell as an example. The linear buckling analysis could produce quick but non-conservative buckling temperature. With considering nonlinearity, implicit quasi-static analysis could predict a relative conservative critical temperature. In addition, the permanent deformations could be obtained to judge if the panel remains visible dent due to the buckling. Finally these two approaches have been compared to thermal bucking behavior of a panel on a vehicle going through thermal cycle of e-coat oven with the excellent agreement on its initial design and issue fix design. In conclusion, the linear buckling analysis could be used for quick thermal buckling evaluation and comparison on a series of proposals.

This paper describes a comprehensive methodology for the simulation of vehicle body panel buckling in an electrophoretic coat (electro-coat or e-coat) and/or paint oven environment. The simulation couples computational heat transfer analysis and structural analysis. Heat transfer analysis is used to predict temperature distribution throughout a vehicle body in curing ovens. The vehicle body temperature profile from the heat transfer analysis is applied as an input for a structural analysis to predict buckling. This study is focused on the radiant section of the curing ovens. The radiant section of the oven has the largest temperature gradients within the body structure. This methodology couples a fully transient thermal analysis to simulate the structure through the electro-coat and paint curing environments with a structural, buckling analysis.