Search Results

The non-conventional diesel nozzles have attracted more and more attention for their ability to promote jet breakup. In the present study, the internal nozzle flow and jet breakup relying on the convergent-divergent nozzle are investigated by combining the cavitation model and LES model with Multi-Fluid-Quasi-VOF model based on the OpenFOAM code. This is a novel method for which the interphase forces caused by the relative velocity of gas and liquid can be taken into account while sharpening the gas-liquid interface, which is able to accurately present the evolution processes of cavitation and jet breakup. Primarily, the numerical model was verified by the mass flow rate, spray momentum flux, discharge coefficient and effective jet velocity of the prototype Spray D nozzle from the literature.

Flash boiling spray is effective in improving the atomization and evaporation characteristics for gasoline direct injection engines. However, for a multi-hole injector the morphology structure of spray has an obvious change with the fuel temperature increasing or the ambient pressure decreasing, which influences the process of mixture formation and flame propagation. Specially, the spray collapses with both long penetration and a narrow spray angle above certain high superheat degree, which deteriorates air/fuel mixing and hence increases emissions. It is not desired for engine applications while the mechanism of spray structure transformation for multi-hole injector still remains unclear. In the present study, a systematic flash boiling spray model for multi-hole injector is built to investigate the flash boiling spray of multi-hole injector.

Multiple-injection strategy for Premixed Charge Compression Ignition (PCCI) combustion was investigated in a four-valve, direct-injection diesel engine by CFD simulation using KIVA-3V code [ 1 ] coupled with detailed chemistry. The effects of fuel splitting proportion, injection timing, included spray angles, injecting velocity, and the combined effects of injection parameters and EGR rate and boost pressure were examined. The mixing process and formations of soot emission and NO x were investigated as the main concern of the research. The results show that the fuel splitting proportion and the injection timing significantly impacted the combustion and emissions due to the considerable changes of the mixing process and fuel distribution in cylinder. The soot emission and unburned HC (UHC) were affected by included spray angles since the massive influences of the fuel distribution resulted from the change in spray targeting point on piston bowl.

The chemical kinetic mechanism determines the ignition timing of homogeneous charge compression ignition (HCCI) engines. The correlation of the ignition delay in shock tubes and HCCI engines under different operating conditions was studied with a reduced mechanism of the primary reference fuel (PRF) composing of n-heptane and iso-octane. According to the similarity analysis of the sensitivity coefficient, the operating conditions which affect the similarity factor are recognized. The results indicate that, under the negative temperature coefficient (NTC) region of the ignition delay in shock tubes, the weight of each reaction on the ignition delay in shock tubes is similar to that in HCCI engines. The ignition delay time in HCCI engines is defined as the period from the time of start of heat release (SHR) with the HRR greater than zero to CA10. At the high equivalence ratios in shock tubes, the similarity factor at the low ambient temperatures is small.

Early injection timing is an effective measure of pre-mixture formation for diesel low-temperature combustion. Three algebraic subgrid models (Smagorinsky model, dynamic Smagorinsky model and WALE model) and one-equation kinetic energy turbulent model using modified TAB breakup model (MTAB model) have been implemented into KIVA3V code to make a detailed large eddy simulation of the atomization and evaporation processes of early injection timing in a constant volume chamber and a Ford high-speed direct-injection diesel engine. The results show that the predictive vapor mass fraction and liquid penetration using LES is in good agreement with the experiment results. In combustion chamber, the sub-grid turbulent kinetic energy and viscosity using LES are less than with the RANS models, and following the increasing time, the sub-grid turbulent kinetic energy and viscosity also increase and are concentrated on the spray area.

Focusing on the dual-mode dual-fuel (DMDF) combustion concept, a combined optimization of the piston bowl geometry with the fuel injection strategy was conducted at low, mid, and high loads. By coupling the KIVA-3V code with the enhanced genetic algorithm (GA), a total of 14 parameters including the piston bowl geometric parameters and the injection parameters were optimized with the objective of meeting Euro VI regulations while improving the fuel efficiency. The optimal piston bowl shape coupled with the corresponding injection strategy was summarized and integrated at various loads. Furthermore, the effects of the key geometric parameters were investigated in terms of organizing the in-cylinder flow, influencing the energy distribution, and affecting the emissions. The results indicate that the behavior of the DMDF combustion mode is further enhanced in the aspects of improving the fuel economy and controlling the emissions after the bowl geometry optimization.

Syngas is considered to be a promising alternative fuel for the dual-fuel reactivity controlled compression ignition (RCCI) engine to reduce the fuel consumption and emissions. However, the optimal syngas compositions and fuel supply strategies in RCCI combustion are significantly affected by engine configurations, which have not been investigated yet. In this study, by integrating the KIVA-3V code and the non-dominated sort genetic algorithm II (NSGA-II), the optimizations for a 0.477 L single-cylinder engine with shallow/wide piston bowl (Engine A) and a 1.325 L single-cylinder engine with conventional omega-type piston (Engine B) under the syngas/diesel RCCI combustion were performed. The optimized operating parameters include the fuel-supply strategies, syngas compositions, and intake conditions. The results indicate that the fuel-supply strategy is flexible in Engine A due to the shallow/wide piston bowl and the relatively small cylinder bore.