Search Results

In recent years, engine calibration became a very hard task because of the increasing complexity of systems and the severity of the depollution norms regarding Real Driving Emissions (RDE). In particular, optimal engine control during dynamic phases became crucial for reducing pollutant emissions. Beyond the classical engine calibration method based on steady state experiments, methods that integrate the dynamical response of the engine constitute therefore a promising approach. This work proposes a global approach of engine dynamical model-based calibration (DMBC) and optimization based on a dynamic Design of Experiments (DDoE). After a general description of the architecture of the calibration process, the paper focuses on the methodology for the design of DDoE.

Today turbochargers are used by car manufacturers on Diesel engines and on an increasing number of gasoline engines, especially in the scope of downsizing. This component has to be well understood and modeled as simulation is widely used at every step of the development. Indeed development cost and time have to be reduced to fulfill both customers’ wishes and more stringent emissions standards. Current turbocharger simulation codes are mostly based on look-up tables (air mass flow and efficiency) given by manufacturers. This raises two points. Firstly, the characteristics are known only in the same conditions as manufacturers’ tests. Secondly, the turbine efficiency given by turbochargers manufacturers is the product of the isentropic efficiency and the turbocharger mechanical efficiency. This global efficiency is suitable for the calculation of the power transferred to the compressor.

Energy recovery of internal combustion engines has proved to be of primary interest to increase engine global efficiency. The motivation behind is to meet future fuel economy requirements and more stringent emissions regulations. Among all engine waste, research has shown that exhaust energy is the most promising solution due to its high availability. In this context, this paper deals with the analysis of the potential of exhaust heat recovery, especially by a turbocompound system. Turbo-compounding is already established in heavy-duty engines, in which an additional stage of expansion is made through an exhaust recovery turbine. This technique is now being studied for small displacement engines. In the first part of this document, a short history on turbocompounding is presented. Then we present a simulation study conducted on AMESim software, using a 0D 2L diesel engine model, calibrated to fit real engine test bench results.

A new methodology for modeling engine intake has been presented; it is based on a transfer function relating pressure response and mass flow rate that makes use of the corresponding frequency spectrum obtained on the so-called “dynamic flow bench”. This new approach provides a way to obtain fast and robust results, which take into account all the phenomena inherent to compressible unsteady flows. Recently the potential of this method has been explored by incorporating it in a GT-Power model to produce a coupled frequency - time domain simulation of a naturally aspirated engine. The method exhibited promising results. One strategy utilized to combat the increasingly stringent emissions standards and reduce fuel consumption is to employ downsized turbocharged engines equipped with charge air coolers (CAC). Therefore, research and development must focus not only on naturally aspirated engines but also on turbocharged ones.

In order to reduce greenhouse gases and respect stringent pollutant emission regulations, the modern engine is increasingly required to incorporate energy recovery systems to enhance performance and increase efficiency. This paper deals with the exhaust energy recovery through turbocompounding. Both series and parallel turbocompounds are discussed. In the first part of the document, literature on turbocompounding is introduced. Then a simulation study carried on AMESim software, using a 2L Diesel engine model is presented. The parallel turbocompounding is simulated by expanding a part of the exhaust gases in a converging nozzle instead of the turbocharger turbine. The power produced is evaluated as a function of the pressure drop in case a turbine is mounted instead of the nozzle. A global study over the entire engine map is described, and two steady state points 2000 rpm, 8 bar and 3500 rpm, 7 bar are chosen.

Unsteady flow in the inlet and exhaust systems of Internal Combustion Engines can be simulated with multi-dimensional simulation codes. Due to their computational time, other methods are widely used and give the opportunity of coupling it with a model of the complete engine. This paper reports on an investigation undertaken to compare the accuracy of the method of inertia, the acoustic method and the one-dimensional method for modeling the gas flow in pipe systems. Results of this study give the advantage and disadvantage of each approach. The comparison shows good agreement between one-dimensional and experimental results while the calculation time is kept acceptable.

Unsteady intake wave dynamics have a first order influence on an engine's performance and fuel economy. There is an abundant literature particularly for naturally aspirated SI engines on the subject of intake manifolds and primary runner lengths aimed to achieve a tuned intake air line. A more demanding design for today's engines is to increase efficiency to meet the requirements of lower fuel consumption and CO2 emissions. Today's tendencies are downsizing the engine to meet these demands. And for drivability purposes, the engine is combined with a turbocharger coupled with a charge air cooler. However, when the engine's displacement is reduced, it will be very dependent on its boosting system. A particularly interesting point to address corresponds to the engine's operation in the low speed range and during transients where the engine has large pumping losses and poor boost pressure. This operation point can be optimized using acoustic supercharging techniques.

Emission regulations have become increasingly stringent in recent years. Current regulations need the development of a new worldwide driving cycle which gives greater weight to the pollutants emitted during transient phases or cold starts. Powertrains contain a large number of components such as multistage turbocharger systems; exhaust gas recirculation, after-treatment devices and sometimes an electric motor. In this context, 0D predictive models of heat transfer in the exhaust line, calibrated with experimental data, are particularly interesting. Many investigations are related to the development of precise control laws in order to optimize the light-off of after-treatment elements during the engine starting phase. A better understanding of the thermal phenomena occurring in the exhaust line is necessary. To study the heat transfer in the exhaust line of a Diesel engine during transient conditions, the temperature in the exhaust line must be known precisely.

To comply with the evermore stringent polluting emission regulation, such as Euro 6c and its new homologation WTLP cycle, the use of turbochargers, already high in Diesel engines, is steeply rising in Gasoline ones. Turbochargers come into a large variety of implementations such as single/two stage(s) or even parallel. In the meantime, car manufacturers intend to decrease development cost and time by using more and more simulation over experimental measurements. However, usual turbocharger models have not followed this trend of modernity. While the heating part of the standard driving test cycle becomes a major topic, turbocharger models are still map based, built from turbocharger manufacturer’s data and measured only in hot conditions. To improve their accuracy, new turbocharger models need to take into account the thermal transfers.

Transport sector decarbonization is a key requirement to achieve Green House Gases emissions reduction. Future regulations and the large deployment of Low Emission Zones (LEZ) will lead to deep changes in this sector. The green hydrogen appears as a promising fuel, containing no carbon. H2 Internal combustion engine (H2 ICE) offers the opportunities of quick refueling, known reliability, relative low total cost of ownership. It is based on mature manufacturing processes and tools. Hence this solution can be commercialized in a near future, offering a short term pathway to decarbonization and a H2 market growth accelerator. However, hydrogen combustion in air generates NOx emissions, which should be reduced close to zero to fulfill future requirements. The HyMot project gathers seven public and industrial partners to develop an H2 engine for Light Commercial Vehicle (LCV) application offering the same performances as the replaced Diesel Engine.