Search Results

Measurements of ignition behavior, homogeneous reactor simulations employing detailed kinetics, and quantitative in-cylinder imaging of fuel-air distributions are used to delineate the impact of temperature, dilution, pilot injection mass, and injection pressure on the pilot ignition process. For dilute, low-temperature conditions characterized by a lengthy ignition delay, pilot ignition is impeded by the formation of excessively lean mixture. Under these conditions, smaller pilot mass or higher injection pressures further lengthen the pilot ignition delay. Similarly, excessively rich mixtures formed under relatively short ignition delay conditions typical of conventional diesel combustion will also prolong the ignition delay. In this latter case, smaller pilot mass or higher injection pressures will shorten the ignition delay. The minimum charge temperature required to effect a robust pilot ignition event is strongly dependent on charge O2 concentration.

The influence of fuel composition on sprays was studied in an injection chamber at DISI conditions with late injection timing. Fuels with high, mid and low volatility (n-hexane, n-heptane, n-decane) and a 3-component mixture with similar fuel properties like gasoline were investigated. The injection conditions were chosen to model suppressed or rapid evaporation. Mie scattering imaging and phase Doppler anemometry were used to investigate the liquid spray structure. A spray model was set up applying the CFD-Code OpenFOAM. The atomization was found to be different for n-decane that showed a smaller average droplet size due to viscosity dependence of injected mass. And for evaporating conditions, a stratification of the vapor components in the 3-component fuel spray was observed.

Detailed experimental investigation of fuel sprays are of utmost importance for the development of appropriate injection systems for gasoline direct injection (GDI) engines. A number of laser based techniques have been developed to study the spray formation. The temperature of the gas phase surrounding the fuel droplets was not accessible up to now. In this work for the first time, to the best of our knowledge, gas-phase temperatures were measured within the vaporizing spray of a high pressure GDI injector using pure rotational coherent anti-Stokes Raman spectroscopy (CARS). Results from an isooctane fuel spray of a multi-hole injector in a heated injection chamber are presented with the probe volume located at a distance of 70mm downstream the injector nozzle in the centre of the spray cone.

The optimization of the vaporization and mixture formation process is of great importance for the development of modern gasoline direct injection (GDI) engines, because it influences the subsequent processes of the ignition, combustion and pollutant formation significantly. In consequence, the subject of this work was the development of a measurement technique based on the laser induced exciplex fluorescence (LIF), which allows the two dimensional visualization and quantification of the in-cylinder air/fuel ratio. A tracer concept consisting of benzene and triethylamine dissolved in a non-fluorescent base fuel has been used. The calibration of the equivalence ratio proportional LIF-signal was performed directly inside the engine, at a well known mixture composition, immediately before the direct injection measurements were started.

Multi-hole DI injectors are being adopted in the advanced downsized DISI ICE powertrain in the automotive industry worldwide because of their robustness and cost-performance. Although their injector design and spray resembles those of DI diesel injectors, there are many basic but distinct differences due to different injection pressure and fuel properties, the sac design, lower L/D aspect ratios in the nozzle hole, closer spray-to-spray angle and hense interactions. This paper used Phase-Contrast X ray techniques to visualize the spray near a 3-hole DI gasoline research model injector exit and compared to the visible light visualization and the internal flow predictions using with multi-dimensional multi-phase CFD simulations. The results show that strong interactions of the vortex strings, cavitation, and turbulence in and near the nozzles make the multi-phase turbulent flow very complicated and dominate the near nozzle breakup mechanisms quite unlike those of diesel injections.

Mie-Scattering and laser induced exciplex fluorescence (LIEF) were used to visualize the distribution of liquid fuel and fuel vapor inside an optical accessible one-cylinder research engine with gasoline direct injection (GDI). Using a tracer which was developed especially for the environments of gasoline combustion engines, LIEF enables an extensive separation between liquid and vapor phase and delivers a signal proportional to the equivalence ratio. Simultaneous images of LIEF and Mie scattering proof the high quality of the phase separation using this tracer concept. The mixture formation process will be shown exemplary at one operation point with homogeneous load and another with stratified load. First results of determining the air/fuel ratio by means of linear Raman spectroscopy will be presented and compared with the two-dimensional qualitative distribution of the fuel vapor (LIEF).