Standard
Plastic Hose Fittings
2022-02-03
WIP
J3275
Standardize plastic fitting hose terminations and drop distances for SAE J2044 fittings
Search Results
Standard
Type “F” Clamps for Plumbing Applications
2022-02-02
CURRENT
J1670_202202
This SAE Standard covers complete dimensional and general specifications for worm drive hose clamps for general use in the plumbing industry.
Standard
Type "F" Clamps for Plumbing Applications
2008-12-02
HISTORICAL
J1670_200812
This SAE Standard covers complete dimensional and general specifications for worm drive hose clamps for general use in the plumbing industry.
Standard
Test Method for Evaluating the Electrochemical Resistance of Coolant System Hoses and Materials
2000-06-30
HISTORICAL
J1684_200006
This test method provides a standardized procedure for evaluating the electrochemical resistance of automotive coolant hose and materials. Electrochemical degradation has been determined to be a major cause of EPDM coolant system hose failures. The test method consists of a procedure which induces voltage to a test specimen while it is exposed to a water/coolant solution. Method #1, referred to as a “Brabolyzer” test, is a whole hose test. Method #2, referred to as a “U” tube test, uses cured plate samples or plates prepared from tube material removed from hose (Method No. 2 is intended as a screening test only). Any test parameters other than those specified in this SAE Recommended Practice, are to be agreed to by the tester and the requester.
Standard
Windshield Washer Tubing
2006-03-03
HISTORICAL
J1037_200603
This SAE Standard covers nonreinforced, extruded, flexible tubing intended primarily for use as fluid lines for automotive windshield washer systems which conform to the requirements of SAE J942.
Standard
Windshield Washer Tubing
2001-08-07
HISTORICAL
J1037_200108
This SAE Standard covers nonreinforced, extruded, flexible tubing intended primarily for use as fluid lines for automotive windshield washer systems which conform to the requirements of SAE J942.
Standard
Windshield Washer Tubing
2015-04-21
CURRENT
J1037_201504
This SAE Standard covers nonreinforced, extruded, flexible tubing intended primarily for use as fluid lines for automotive windshield washer systems which conform to the requirements of SAE J942.
Standard
Low-Permeation Fuel Fill and Vent Tube
2021-09-14
CURRENT
J2405_202109
This SAE Standard covers the minimum requirements for a low-permeation tubing (100 g/m2/day or less) for use as a low pressure (14.5 kPa) liquid- or vapor-carrying component for use in gasoline or diesel fuel filler, vent, and vapor systems. The construction shall be designed to be functional over a temperature range of -40 to 100 °C for the T1 designation, or -40 to 125 °C for the T2 designation.
Standard
Recommended Practices for Design and Evaluation of Passenger and Light Truck Coolant Hose Clamped Joints
2013-07-09
CURRENT
J1697_201307
This SAE Recommended Practice covers recommended practices for design and evaluation of hose clamped joints primarily in automotive applications. It is intended to: (a) evaluate current joint designs, (b) compare existing designs, (c) aid in the development of new designs, (d) give objective results once weights are set, (e) rate the overall design and individual sections of design, and (f) encourage future research by industry and the OEM's.
Standard
Test Method for Evaluating the Electrical Resistance of Coolant System Hose Covers
2021-08-12
CURRENT
J2790_202108
This test method provides a standardized procedure for evaluating the electrical resistance of automotive coolant hose covers. It is known that an electrical potential exists between the engine and the radiator. Coolant hose cover conductivity has been determined to be a factor to reduce hose clamp life when vehicle build variations allow possible contact of the hose or the clamp to metal components on the radiator and engine thus completing an electrical circuit. The ensuing electrical current can undercut the clamp protective coating, leaving it vulnerable to the corrosive effects of road salts, moisture, and other environmental contaminants. SAE Recommended Practice J1684 addresses the electrochemical resistance of the tube portion of the coolant hose.
Standard
TRANSMISSION OIL COOLER HOSE
1988-10-01
HISTORICAL
J1532_198810
This specification covers two types of hose, Type A and B, for use with automatic transmission fluid within a temperature range of -40 to +125°C (-40 to +257°F). Recommended maximum operating pressure for Type A hose is 1.73 mPa (250 psi) and 1.03 mPa (150 psi) for Type B hose. The lower pressure Type B hose is specifically for auxiliary cooler applications only.
Standard
TRANSMISSION OIL COOLER HOSE
1993-06-01
HISTORICAL
J1532_199306
This SAE Standard covers four types of hose for use with automatic transmission fluid: A, B, AT, and BT. Type A and Type B are for use within a temperature range of -40 to 125 °C (-40 to 257 °F) while types AT and BT are for use within a temperature range of -40 to 150 °C (-40 to 302 °F). Recommended maximum operating pressure for Type A and Type AT hose is 1.7 MPa (250 psi) while recommended maximum operating pressure for Type B and Type BT hose is 1.0 MPa (150 psi). The lower pressure (Types B and BT) hose is for auxiliary cooler applications only. The reference fluid for tests requiring the use of automatic transmission fluid shall be Dexron-II E/Mercon or equivalent.
Standard
TRANSMISSION OIL COOLER HOSE
1989-04-01
HISTORICAL
J1532_198904
This specification covers two types of hose, Type A and B, for use with automatic transmission fluid within a temperature range of -40 to +125°C (-40 to +257°F). Recommended maximum operating pressure for Type A hose is 1.73 MPa (250 psi) and 1.03 MPa (150 psi) for Type B hose. The lower pressure Type B hose is specifically for auxiliary cooler applications only.
Standard
TRANSMISSION OIL COOLER HOSE
1995-02-01
HISTORICAL
J1532_199502
This SAE Standard covers four types of hose for use with automatic transmission fluid: A, B, AT, and BT. Type A and Type B are for use within a temperature range of –40 °C to 125 °C (–40 °F to 257 °F) while types AT and BT are for use within a temperature range of –40 °C to 150 °C (–40 °F to 302 °F). Recommended maximum operating pressure for Type A and Type AT hose is 1.7 MPa (250 psi) while recommended maximum operating pressure for Type B and Type BT hose is 1.0 MPa (150 psi). The lower pressure (Types B and BT) hose is for auxiliary cooler applications only. The reference fluid for tests requiring the use of automatic transmission fluid shall be Dexron-II E/Mercon or equivalent.
Standard
Transmission Oil Cooler Hose
2005-03-07
HISTORICAL
J1532_200503
This SAE Standard covers hose intended for use with automatic transmission cooling system applications. Type A hoses are intended for original equipment or replacement applications while Type B hoses are intended for aftermarket auxiliary cooler applications only. The reference fluid for tests requiring the use of automatic transmission fluid (ATF) shall be Dexron III / Mercon 5 or equivalent ATF that is agreed to by hose manufacturer and customer.
Standard
Transmission Oil Cooler Hose
2014-06-04
HISTORICAL
J1532_201406
This SAE Standard covers hose intended for use with automatic transmission cooling system applications. Type A hoses are intended for original equipment or replacement applications while Type B hoses are intended for aftermarket auxiliary cooler applications only. The reference fluid for tests requiring the use of automatic transmission fluid (ATF) shall be Dexron III / Mercon 5 or equivalent ATF that is agreed to by hose manufacturer and customer.
Standard
Transmission Oil Cooler Hose
2021-06-10
CURRENT
J1532_202106
This SAE Standard covers hose intended for use with automatic transmission cooling system applications. Type A hoses are intended for original equipment or replacement applications while Type B hoses are intended for aftermarket auxiliary cooler applications only. The reference fluid for tests requiring the use of automatic transmission fluid (ATF) shall be Dexron III / Mercon 5 or equivalent ATF that is agreed to by hose manufacturer and customer.
Standard
Compression Set of Hoses or Solid Discs
2004-11-30
HISTORICAL
J1638_200411
This SAE Recommended Practice is used for establishing the compression set that could be expected to occur with a thermoset elastomeric hose under securing clamps. It seeks to reproduce the type of indentation caused by the clamps in the wall of a hose. An excessive compression set measured by this method may indicate a hose that could eventually allow leakage of fluid or gas past the clamps in service.
Standard
Compression Set of Hoses or Solid Discs
2015-04-21
CURRENT
J1638_201504
This SAE Recommended Practice is used for establishing the compression set that could be expected to occur with a thermoset elastomeric hose under securing clamps. It seeks to reproduce the type of indentation caused by the clamps in the wall of a hose. An excessive compression set measured by this method may indicate a hose that could eventually allow leakage of fluid or gas past the clamps in service.
Standard
COMPRESSION SET OF HOSES OR SOLID DISCS
1993-05-01
HISTORICAL
J1638_199305
This SAE Recommended Practice is used for establishing the compression set that could be expected to occur with engine coolant hoses under securing clamps. It seeks to reproduce the type of indentation caused by the clamps in the wall of the hose. An excessive compression set measured by this method would indicate a hose that could eventually allow leakage of coolant past the clamps in service. This method has been found to give repeatable results in the range of 25% to 50% initial compression.
