Search Results

Abstract The non-pneumatic tire (NPT) has been widely used due to its advantages of no run-flat, no need for air maintenance, low rolling resistance, and improvement of passenger comfort due to its better shock absorption. It has a variety of applications in military vehicles, earthmovers, the lunar rover, stair-climbing vehicles, etc. Recently, the Unique Puncture-Proof Tire System (UPTIS) NPT has been introduced for passenger vehicles. In this study, three different design configurations, viz., Tweel, Honeycomb, and newly developed UPTIS, have been compared. The effect of polyurethane (PU) material nonlinearity has also been introduced by applying five different nonlinear PU material properties in the spokes. The combined analysis of the PU material nonlinearity and spoke design configuration on the overall tire stiffness and spoke damage prediction is done using three-dimensional (3D) finite element modelling (FEM) simulations performed in ANSYS 16.0.

Abstract This article presents a comprehensive investigation for the interaction between vehicle ride vibration control and braking control using two degrees of freedom (2DOF) quarter vehicle model. A typical limited bandwidth active suspension system with nonlinear spring and damping characteristics of practical hydraulic and pneumatic components is controlled to regulate both suspension and tire forces and therefore provide the optimum ride comfort and braking performance of an anti-lock brake system (ABS). In order to design a suitable controller for this nonlinear integrated system, various control techniques are followed including state feedback tuned using Linear Quadratic Regulator (LQR), state feedback tuned using Genetic Algorithm (GA), Proportional Integrated (PI) tuned genetically, and Fuzzy Logic Control (FLC). The ABS control system is designed to limit skid ratio below threshold of 15%.

Abstract In this article, compared with traditional Remote Parameter Control (RPC), the iterative process is improved based on linear transfer function (TF) estimation of the nonlinear dynamic system. In the improved RPC, the iteration coefficient is designed according to the convergence condition of the nonlinear iterative process, so that the convergence level, convergence speed, and iteration stability could be improved. The difference between the traditional and the improved RPC iterative process is discussed, the RPC iterative process of the nonlinear system is analyzed, and channel decoupling for Multi-Input Multi-Output (MIMO) system based on eigen-decomposition of the system TF and linear TF estimation is introduced. It assumes that the eigenvector matrix of the system TF remains the same, and the linear TF in the iterative process is estimated and updated, which is used for iterative calculation.

Abstract Path tracking is an essential stage for vehicle safety control. It is more newsworthy than ever in the automotive context and especially for autonomous vehicle. The study proposes an optimal control method for path tracking problem in inverse vehicle handling dynamics. The proposed method generates an expected trajectory which guarantees minimum clearance to the prescribed path by identifying the optimal steering torque input. Based on this purpose, the path tracking problem, which is treated as an optimal control problem, is then solved by local collocation method and mesh refinement. Finally, a real vehicle test is executed to verify the rationality of the proposed model and methodology. The results show that using control variables as a mesh refinement function can capture the dramatic changes in state variables, and the efficiency improvement is more significant as the number of the grid points increases.

Abstract It is reasonable to use a two-phase heat transfer loop (TPL) in a thermal control system (TCS) of spacecraft with large heat dissipation. One of the key elements of TPL is a heat-controlled accumulator (HCA). The HCA represents a volume which is filled with vapor and liquid of a single working fluid without bellows. The pressure in a HCA is controlled by the heater. The heat and mass transfer processes in the HCA can proceed with a significant nonequilibrium. This has implications on the regulation of TPL. This article presents a mathematical model of nonequilibrium heat and mass transfer processes in an HCA for microgravity conditions. The model uses the equations of mass and energy conservation separately for the vapor and liquid phases. Interfacial heat and mass transfer is also taken into account. It proposes to use the convective component k for the level of nonequilibrium evaluation.

Abstract Commercial vehicles contribute to the majority of freight transportation in the United States. They are also significant fuel consumers, with over 23% of fuel used in transportation in the United States. The gas price volatility and increasingly stringent regulation on greenhouse-gas emissions have driven manufacturers to adopt new fuel-efficient technologies. Among others, an advanced transmission control strategy, which can provide tangible improvement with low incremental cost. In the commercial sector, individual drivers have little or no interest in vehicle fuel economy, contrary to fleet owners. Aggressive driving behavior can greatly increase the real-world vehicle fuel consumption. However, the effectiveness of transmission calibration to match the shift strategy to the driving characteristics is still a challenge.

Abstract In this article, a unique design for Hydro-Pneumatic Energy Harvesting Suspension HPEHS system is introduced. The design includes a hydraulic rectifier to maintain one-way flow direction in order to obtain maximum power generation from the vertical oscillation of the suspension system and achieve handling and comfort car drive. A mathematical model is presented to study the system dynamics and non-linear effects for HPEHS system. A simulation model is created by using Advanced Modeling Environment Simulations software (AMEsim) to analyze system performance. Furthermore, a co-simulation platform model is developed using Matlab-Simulink and AMEsim to optimize the PID controller parameters of the external variable load resistor applied on the generator by using Particle Swarm Optimization (PSO).

Abstract This research developed methods for a virtual operator model (VOM) to learn the optimal control inputs for operation of a virtual excavator. Virtual design, used to model, simulate, and test new features, has often been limited by the fidelity of the virtual model of human operators. Human operator learns, over time, the capability, limits, and control characteristics of new vehicles to develop the best strategy to maximize the efficiency of operation. However, VOMs are developed with fixed strategies and for specific vehicle models (VMs) and require time-consuming re-tuning of the VOM for each new vehicle design. Thus, there typically is no capability to optimize strategies, taking account of variation in vehicle capabilities and limitations. A VOM learning capability was developed to optimize control inputs for the swing-to-pile task of a trenching operation. Different control strategies consisted of varied combinations of speed control, position control, and coast.

Abstract Vehicle cabin air quality depends on various parameters such as number of passengers, fan speed, and vehicle speed. In addition to controlling the temperature inside the vehicle, HVAC control system has evolved to improve cabin air quality as well. However, there is no standard test method to ensure reliable and repeatable comparison among different cars. The current study defined Cabin Air Quality Index (CAQI) and proposed a test method to determine CAQI. CAQIparticles showed dependence on the choice of metrics among particle number (PN), particle surface area (PS), and particle mass (PM). CAQIparticles is less than 1 while CAQICO2 is larger than 1. The proposed test method is promising but needs further improvement for smaller coefficient of variations (COVs).

Abstract On contrast to the qualitative approach used in the majority of researches, an evaluation quantitative approach is introduced not only to depict the plain individual effect of the influence of the high-pressure torsion (HPT) processing conditions on the microstructural and Hv-values of the ultra-hard nanostructured AA6061-15%SiCp composite but also to detect its possible parameters functional interaction and nonlinear trends involved. Experimental data were used to establish many adequate and significant empirical models to detect and to evaluate the mutual functional interrelationships between the Hv-values of the composite, each of HPT processing pressure, and number of revolutions. For each group of interrelated parameters, the preferred selected developed model has been exploited to generate the relevant contours and response surface graphs.

Abstract A key element in an ergonomically designed driver’s seat in a car is the correct identification of driver seating position and posture accommodation. Current practice by the automotive Original Equipment Manufacturer (OEM) is to utilize the Society of Automotive Engineering (SAE) J1517 standard practice as a reference. However, it was found that utilizing such guidelines, which were developed based on the American population, did not fit well with the anthropometry and stature of the Malaysian population. This research seeks to address this issue by comparing the SAE J1517 Model against Malaysian preferred driving position. A total of 62 respondents were involved for the driver seating position and accommodation study in the vehicle driver’s seat buck mockup survey and measurements. The results have shown that the Malaysian drivers prefer to sit forward as compared to the SAE J1517 Model and have shorter posture joint angle.

Abstract Catalytic converters, a primary component in most automotive emissions control systems, do not function well until they are heated substantially above ambient temperature. As the primary energy for catalyst heating comes from engine exhaust gases, plug-in hybrid electric vehicles (PHEVs) that have the potential for short and infrequent use of their onboard engine may have limited energy available for catalytic converter heating. This article presents a comparison of multiple hybrid supervisory control strategies to determine the ability to avoid engine cold starts during a blended charge-depleting propulsion mode. Full vehicle and catalytic converter simulations are performed in parallel with engine dynamometer testing in order to examine catalyst temperature variations during the course of the US06 City drive cycle. Emissions and energy consumption (E&EC) calculations are also performed to determine the effective number of engine starts during the drive cycle.

Abstract During certain driving scenarios, low-speed engine vibrations get propagated to the driveline and affect the drivability of a vehicle. To reduce the impact of these vibrations, a locked torque converter lockup clutch (TCC) is allowed to temporarily slip to increase the damping in the driveline. However, the initial slow dynamics of the fluid path of the torque converter cause the vehicle to feel sluggish. In this article, we design a model predictive controller (MPC) that optimally controls the torque request from the actuator (i.e., engine or e-motor) and the lockup clutch capacity for reducing this sluggishness. The study is conducted for a light-duty vehicle and uses an experimentally validated, detailed full-order model (FOM) for developing and validating a computationally efficient, reduced-order driveline model (ROM).

Abstract A critical component of vehicle dynamic control systems is the accurate and real-time knowledge of the vehicle’s key states and parameters when running on the road. Such knowledge is also essential for vehicle closed-loop feedback control. Vehicle state and parameter estimation has gradually become an important way to soft-sense some variables that are difficult to measure directly using general sensors. In this work, a seven degrees-of-freedom (7-DOF) nonlinear vehicle dynamics model is established, where consideration of the Magic formula tire model allows us to estimate several vehicle key states using a hybrid algorithm containing an unscented Kalman filter (UKF) and a genetic algorithm (GA). An estimator based on the hybrid algorithm is compared with an estimator based on just a UKF. The results show that the proposed estimator has higher accuracy and fewer computation requirements than the UKF estimator.

Abstract The principal issue in choosing an energy management strategy (EMS) for hybrid electric vehicles (HEVs) has been the way of determining the optimal share of electric energy in hybrid drive. In this article, a novel EMS is proposed that, along with maximum engine efficiency in the hybrid drive, can optimize the share of battery energy for the maximum efficiency of vehicle power train expanded with an imaginary power plant that, by delivering the electric energy to a grid, feeds the vehicle battery. It is proved that the expanded power train efficiency has the local maximum for a wide range of wheel power demand. The relation between the wheel power demand in hybrid drive, the share of battery energy, and the maximum efficiency of the expanded power train is conducted offline. Downloaded to the onboard control system, it enables the operation with the instantaneously optimal share of battery energy and the control system to operate with the low computational load.

Abstract Hybrid Electric Vehicles (HEVs) achieve better fuel economy than conventional vehicles by utilizing two different power sources: an internal combustion engine and an electrical motor. The power distribution between these two components must be controlled using some algorithm, be it rule based, optimization based, or reinforcement learning based. In the design of such control algorithms, it is important to evaluate the impact that variations of certain design parameters will have on the system performance, in this case, fuel economy. Traditional methods of sensitivity analysis have been applied to various power flow control algorithms to determine their robustness to the variations of HEV design parameters. This article presents a sensitivity analysis of three power flow control algorithms: twin delayed deep deterministic policy gradient (TD3), deep deterministic policy gradient (DDPG), and adaptive equivalent consumption minimization strategy (A-ECMS).

Abstract The aim of this study is to achieve the target transient posture of a vehicle according to the user’s steering operation. The target behavior was hypothesized to be a roll mode in the diving pitch, even during steering inputs on rough surfaces, in order to improve subjective evaluation. As a result of organizing the issues of feedforward control (FF) and feedback control (FB), we hypothesized that it would be appropriate to follow the ideal posture. The model following damping control (MFDC) was newly proposed by the authors as a solution to a control algorithm based on model-following control. The feature employs skyhook control (SH), which follows the deviation between the behavior of the reference model, which generates a target behavior with no input from the road surface, and the actual behavior of the vehicle. Numerical analyses were performed to verify the followability of the target behavior and the effect of roll damping performance.

Abstract Autonomous vehicles require precise knowledge of their position and orientation in all weather and traffic conditions for path planning, perception, control, and general safe operation. Here we derive these requirements for autonomous vehicles based on first principles. We begin with the safety integrity level, defining the allowable probability of failure per hour of operation based on desired improvements on road safety today. This draws comparisons with the localization integrity levels required in aviation and rail where similar numbers are derived at 10−8 probability of failure per hour of operation. We then define the geometry of the problem where the aim is to maintain knowledge that the vehicle is within its lane and to determine what road level it is on.

Abstract In order to further improve the active safety protection of the vehicle’s active collision avoidance system for vulnerable road users, consider the limitations of on-board sensors, a pedestrian active collision avoidance control strategy based on vehicle-to-vehicle (V2V) communication technology is proposed for the blind-spot dangerous scenario where pedestrians pass through the front of a stationary obstacle vehicle and collide with the host vehicle. Firstly, the relative position relationship model between the host vehicle and the pedestrian is established according to the pedestrian information detected by the obstacle vehicle sensor and the global positioning system (GPS) position information of the obstacle vehicle and the host vehicle so that the host vehicle can obtain the state information of the pedestrian in front of the obstacle vehicle through V2V communication.

Abstract Due to the transition of the driver to a passenger as well as the option of non-driving tasks, automated driving will necessitate adjustments of driving dynamics. In order to face higher comfort requirements and mitigate motion sickness not only horizontal dynamics but also vertical dynamics should be concerned. Therefore, we developed a novel control algorithm for active suspension systems, which takes the requirements of autonomous vehicles into account. Due to safety, cost reasons, and the unavailability of automated test vehicles, the controller was built up, tested, and tuned in simulation before final in-car testing. In this article we introduce a combined simulation and testing process for suspension control systems with focus on comfort measures. We successfully apply the method to the mentioned active suspension control algorithm with good accordance between simulation and measurement for low-frequency excitation.